三维非连续变形分析方法碰撞分析及其应用

将具有完备动力学理论的非连续变形分析(DDA)方法应用于块体碰撞研究。基于三维DDA(3D DDA)方法,按时步输出块体碰撞过程速度变化和接触嵌入量,进而得到块体碰撞恢复系数、冲量、冲击力。以此为参考指标,采用斜抛、面-面对心等碰撞模型,验证3D DDA方法模拟块体碰撞的有效性,并将3D DDA方法应用于多米诺骨牌倾倒、滚石边坡成灾及防护等算例分析,探讨了多米诺骨牌倾倒机制、滚石启动及运动行为、滚石灾害防护方案。结果表明:多米诺骨牌间距越大,同一块体被碰撞时间越迟,其最终稳定时间也越迟,与下一块体碰撞的动能越大;滚石运动呈侧向平动及转动三维运动特征,每一次碰撞,均引起动能、轨迹或状态的显著变化;滚石拦挡设施弹簧刚度越大,越先达到最大冲击力,最大冲击力随弹簧刚度的增加而减小;可结合树木阻挡效应,耗散滚石动能,降低滚石飞跃高度,使滚石灾害减轻或控制在防护范围以内。     

水流损失和热补偿共同作用对增强型地热系统(EGS)产能影响的研究

基于青海共和盆地-3705m地热田实测数据,结合流固耦合传热理论并运用Comsol软件,建立了离散型裂隙岩体流体传热模型。考虑水流损失和热补偿共同作用,模拟得到了开采过程中上、下岩层(盖层和垫层)为绝热不渗透、传热不渗透、渗透传热时,储层(上、下岩层和压裂层)温度场的变化特征,分析了产出流量、水流损失、产出温度、产热速率的变化规律。研究结果表明:采热过程中产出流量始终小于注入流量;产出流量增幅速率先增大后减小,最后趋于稳定,前3a产出流量增幅超过总增幅量的3/4;忽略水流损失,将高估产热速率,采热初期甚至达到考虑水流损失时产热速率的3倍以上;考虑水流损失,产热速率呈先快速上升再趋于稳定后逐渐下降的趋势,最优开采时间为3a^11a;研究上、下岩层对产出温度的影响,仅考虑传热,采热寿命延长5.43%,同时考虑渗流传热时,采热寿命延长2.71%;采热前9a,水流损失占主导作用,即流入上、下岩层水流损失对产热速率的影响高于热补偿效应,开采10a后,热补偿效应占主导作用;同时考虑水流损失和热补偿效应得到的产热速率变化规律与实际工程更为符合,建议选择低渗透能力的上、下岩层延长增强型地热系统(EGS)运行时间。     

离子浓度及表面结构对岩石孔隙内水流动特性的影响

酸性环境引发的岩石孔隙表面溶解增加了孔隙内水溶液的盐离子浓度,破坏了孔隙的表面结构.本文采用分子动力学模拟的方法研究了纳米级岩石孔隙内水溶液的流动特性,分析了盐离子浓度和孔隙表面结构对水流速度分布的影响及原因.研究结果表明:纳米级岩石孔隙内的水溶液流动符合泊肃叶流动特性,流速呈"抛物线"分布;随盐离子浓度增加,水溶液内部氢键网络变得更为致密,水黏度随其呈线性增长;水溶液中离子浓度越大,孔隙表面对水流动的阻力越大,最大流速越小,速度分布的"抛物线"曲率半径越大;岩石孔隙表面结构的破坏改变了流动表面的粗糙程度,增加了孔隙表面对H2O分子的吸引力.随表面结构破坏程度的增大,水溶液在近壁区域的密度增大,流速降低;当表面破坏程度达到50%时,水溶液在近壁区域出现了明显的负边界滑移现象.     

Triphilic pentablock copolymers with perfluoroalkyl segment in central position

Adding perfluoroalkyl (PF) segments to amphiphilic copolymers yields triphilic copolymers with new application profiles. Usually, PF segments are attached as terminal blocks via Cu(I) catalyzed azide-alkyne cycloaddition (CuAAC). The purpose of the current study is to design new triphilic architectures with a PF segment in central position. The PF segment bearing bifunctional atom transfer radical polymerization (ATRP) initiator is employed for the fabrication of triphilic poly(propylene oxide)-b-poly(glycerol monomethacrylate)-b-PF-b-poly(glycerol monomethacrylate)-b-poly(propylene oxide) PPO-b-PGMA-b-PF-b-PGMA-b-PPO pentablock copolymers by a combined ATRP and CuAAC reaction approach. Differential scanning calorimetry indicates the PF-initiator to undergo a solid–solid phase transition at 63°C before the final crystal melting at 95°C. This is further corroborated by polarized optical microscopy and X-ray diffraction studies. The PF-initiator could successfully polymerize solketal methacrylate (SMA) under typical ATRP conditions producing well-defined Br-PSMA-b-PF-b-PSMA-Br triblock copolymers that are then converted into PPO-b-PSMA-b-PF-b-PSMA-b-PPO pentablock copolymer via CuAAC reaction. Subsequently, acid hydrolysis of the PSMA blocks afforded water soluble well-defined triphilic pentablock copolymers PPO-b-PGMA-b-PF-b-PGMA-b-PPO with fluorophilic central segment, hydrophilic middle blocks, and lipophilic outer blocks. The triphilic block copolymers could self-assemble, depending upon the preparatory protocol, into spherical and filament-like phase-separated nanostructures as revealed by transmission electron microscopy.     

Amphiphilic pentablock copolymers and their blends with PDMS for antibiofouling coatings

Well‐defined amphiphilic pentablock copolymers Siy‐(EGx‐FAz)₂ composed of polysiloxane (Si), polyethylene glycol (EG), and perfluorohexylethyl polyacrylate (FA) blocks are synthesized by ATRP of FA monomer starting from a difunctional bromo‐terminated macroinitiator. Diblock copolymers EGx‐FAz are also synthesized as model systems. The block copolymers are used, either alone or blended with a PDMS matrix in varied loadings, to prepare antibiofouling coatings. Angle‐resolved XPS and contact angle measurements show that the coating surface is highly enriched in fluorine content but undergoes reconstruction after contact with water. Protein adsorption experiments with human serum albumin and calf serum highlight that diblock copolymers resist protein adhesion better than do pentablock copolymers. Blending of the pentablock copolymer with PDMS results in increased protein adsorption. By contrast, the PDMS‐matrix coatings show high removal percentages of sporelings of the green fouling alga Ulva linza. © 2015 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 2015 , 53, 1213–1225     

Amphiphilic block copolymer self‐assemblies of poly(NVP)‐b‐poly(MDO‐co‐vinyl esters): Tunable dimensions and functionalities

Functional, degradable polymers were synthesized via the copolymerization of vinyl acetate (VAc) and 2‐methylene‐1,3‐dioxepane (MDO) using a macro‐xanthate CTA, poly(N‐vinylpyrrolidone), resulting in the formation of amphiphilic block copolymers of poly(NVP)‐b‐poly(MDO‐co‐VAc). The behavior of the block copolymers in water was investigated and resulted in the formation of self‐assembled nanoparticles containing a hydrophobic core and a hydrophilic corona. The size of the resultant nanoparticles was able to be tuned with variation of the hydrophilic and hydrophobic segments of the core and corona by changing the incorporation of the macro‐CTA as well as the monomer composition in the copolymers, as observed by Dynamic Light Scattering, Static Light Scattering, and Transmission Electron Microscopy analyses. The concept was further applied to a VAc derivative monomer, vinyl bromobutanoate, to incorporate further functionalities such as fluorescent dithiomaleimide groups throughout the polymer backbone using azidation and “click” chemistry as postpolymerization tools to create fluorescently labeled nanoparticles. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2699–2710     

Synthesis of tertiary amine‐based pH‐responsive polymers by RAFT Polymerization

Well‐defined tertiary amine‐based pH‐responsive homopolymers and block copolymers were synthesized via reversible addition‐fragmentation chain transfer (RAFT) polymerization using 4‐cyanopentanoic acid dithiobenzoate (CPAD) as the RAFT agent for homopolymers and a poly(ethylene glycol) (PEG) macro‐RAFT agent for the block copolymers. ¹H NMR and gel permeation chromatography results confirmed the successful synthesis of these homopolymers and block copolymers. Kinetics studies indicated that the formation of both the homopolymers and the block copolymers were well defined. The pKa titration experiments suggested that the homopolymers and the related block copolymers have a similar pKa. The dynamic light scattering investigation showed that all of the block copolymers underwent a sharp transition from unimers to micelles around their pKa and the hydrodynamic diameter (D_h) was not only dependent on the molecular weight but also on the composition of the block copolymers. The polymer solution of PEG‐b‐PPPDEMA formed the largest micelle compare to the PEG‐b‐PDPAEMA and PEG‐b‐PDBAEMA with a similar molecular weight. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1010–1022     

End group polarity and block symmetry effects on cloud point and hydrodynamic diameter of thermoresponsive block copolymers

Thermoresponsive block copolymers are of interest for delivery vehicles in the body. Often an interior domain is designed for the active agent and the exterior domain provides stability in the bloodstream, and may carry a targeting ligand. There is still much to learn about how block sequence and chain end identity affect micelle structure, size, and cloud points. Here, hydrophilic oligo(ethylene glycol) methyl ether acrylate and more hydrophobic di(ethylene glycol) methyl ether methacrylate monomers were polymerized to give amphiphilic block copolymers with amphiphilic chain ends. The block sequence and chain end identity were both controlled by appropriate choice of RAFT chain transfer agents to study the effect of ‘matched’ and ‘mismatched’ chain end polarity with amphiphilic block sequence. The affect of matching or mismatching chain end polarity and block sequence was studied on the hydrodynamic diameter, cloud point, and temperature range of the chain collapse on linear di‐ and triblock copolymers and star diblock polymers. The affects of matching or mismatching chain end polarity were significant with linear diblock copolymers but more complex with triblock and star copolymers. Explanations of these results may help guide others in designing thermoresponsive block copolymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2838–2848     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

Synthesis and Self-Assembly of Mixed-Graft Block Copolymers

Mixed-graft block copolymers (mGBCPs) consist of two or more types of polymeric side chains grafted on a linear backbone in a random, alternating, or pseudo-alternating sequence. They can phase-separate with the backbone serving as the interface of the blocks, and the side chains dominate their self-assembly behavior. mGBCPs are an accessible polymer architecture for exploring the idea of encoding polymer properties through the macromolecular architecture, as there are two distinct structural components that can be tuned: the backbone and the side chains. In this Concept article, the current literature on the synthesis of mGBCPs is reviewed, and the advantages and disadvantages of each synthetic method are noted. The self-assembly of mGBCPs is also discussed where possible. Finally, directions for future research on mGBCP synthesis and self-assembly are suggested.