具有弹性支座杆件的动力稳定性研究

研究了杆件具有弹性支座时直杆的动力稳定性问题，推导出了杆件的临界频率和动力不稳定边界，分析了弹簧刚度和阻尼对杆件动力稳定性的影响，研究表明杆件的侧向刚度愈大其结构的动力稳定性愈好，阻尼对杆的振动起有利作用，并提出了在实际工程中减小杆件振动的一些措施．     

Laminar flow and heat transfer in confined channel flow past square bars arranged side by side

A numerical investigation was conducted to analyze the unsteady laminar flow field and heat transfer characteristics in a plane channel with two square bars mounted side by side to the approaching flow. A finite volume technique is applied with a fine grid and time resolution. The transverse separation distance between the bars (G/d) is varied from 0 to 5, whereas the bar height to channel height is d/H=1/8, and the channel length is L=5H. Different flow regimes develop in the channel due the interaction between the two mounted square bars, steady flow, flow with vortex shedding synchronization either in phase or in anti-phase, or biased flow with low frequency modulation of vortex shedding are found. Results show that the pressure drop increase and heat transfer enhancement are strongly dependent of the transverse separation distance of the bars and the channel Reynolds number.     

Forced Nonstationary Vibrations of a Sandwich Cylindrical Shell with Cross-Ribbed Core

The equations of nonaxisymmetric vibrations of sandwich cylindrical shells with discrete core under nonstationary loading are presented. The components of the elastic structure are analyzed using a refined Timoshenko theory of shells and rods. The numerical method used to solve the dynamic equations is based on the integro-interpolation method of constructing finite-difference schemes for equations with discontinuous coefficients. The dynamic problem for a sandwich cylindrical shell under distributed nonstationary loading is solved with regard for the discreteness of the core__________Translated from Prikladnaya Mekhanika, Vol. 41, No. 2, pp. 60–67, February 2005.     

On the stability of elastic curved bars

A general discussion about the stability of arbitrary elastic curved bars in space under combined actions of bending and twisting is given in this paper. A system of Eqs. (28)–(36) for perturbation functions near some equilibrium state is presented. With appropriate boundary conditions, the nontrivial solution corresponds to the critical state. Five examples are analysed in this paper. Some of them are new results and others are old problems treated using the new method.     

百瓦级高亮度光纤耦合半导体激光模块的研制

用3只976 nm半导体激光短列阵作为子模块,研制出连续工作的百瓦级高亮度光纤耦合模块。首先,利用光束转换器将每个半导体激光短列阵进行光束整形;然后采用空间复用技术将3个半导体激光短列阵在光参数积小的方向上叠加,并利用倒置伽利略望远镜作为扩束器进一步压缩发散角;最后利用优化结构的透镜组将激光聚焦到芯径200 μm,数值孔径为0.22的光纤中。测量结果显示:聚焦后激光的发散角为24.8°,焦平面的光斑尺寸为175.2 μm;耦合后测量光纤出光功率可达107 W,对应亮度为2.23 MW/(cm²·sr),达到了国内利用列阵进行光纤耦合的领先水平;在工作电流为52.5 A时,电光转换效率为43.1%,远高于全固态等激光器;最后测量本模块在不同驱动电流时的光谱,并以此计算出模块的热阻为1.29 K/W,说明它的散热性能良好。结果表明,本光纤耦合模块适合应用于泵浦光纤激光器、医疗和激光加工等领域。     

半圆形粗糙元壁面颗粒沉积数值模拟研究

为研究半圆形粗糙元壁面对颗粒沉积的影响,分别采用雷诺应力模型（RSM）和离散相模型（DPM）求解流场与颗粒运动轨迹,并结合临界速度判别颗粒沉积的方法。通过构建不同半圆形粗糙元参数（e/D,p/e）的通风管道计算域,研究了1~10 μm颗粒沉积速度变化及沿气流方向颗粒的沉积趋势,分析了流场所引起的湍流变化对颗粒沉积的影响,与相同参数下的方形粗糙元壁面颗粒沉积特性进行了对比。同时,分析了粗糙元参数对颗粒沉积速度的影响。结果发现,半圆形壁面颗粒沉积速度小于同参数下的方形壁面颗粒沉积速度,这是由于半圆形壁面的回流区相对方形粗糙元更小,捕捉颗粒能力差,半圆形粗糙元流体附壁效应导致半圆形粗糙元拦截效率较低。当e/D=0.02,p/e=3时,颗粒沉积速度变化较大,但在其余参数下变化并不大。半圆形粗糙元壁面的迎风面是颗粒沉积的主要区域。     

线弹性幂强化材料平面杆系弹塑性分析的数值解

各杆任意铰接在一个刚体上的平面杆系是一种比较复杂的杆系结构,某些其它类型的平面杆系常常可以看作是它的特例。本文将材料的本构关系描述为线性幂强化形式,推导出了该类平面杆系结构弹塑性分析的普遍表达式,编制了通用程序,使这一类问题有了一个通用的解题方法。     

Numerical and Experimental Comparative Study on Nanofluids Flow and Heat Transfer in a Ribbed Triangular Duct

Numerical and experimental investigation is carried out to study the effect of combined vortex generator and nanofluids on turbulent heat transfer and fluid flow characteristics in an equilateral triangular duct. A triangular duct provides a lower heat transfer rate and lower pressure drop compared to other duct configurations. The improvement of heat transfer of these ducts increases their importance for providing higher heat transfer and lower pressure drop. Two different types of nanoparticles, namely Al₂O₃ and SiO₂, suspended in distilled water with two particle concentrations are successfully prepared and experimentally tested. The numerical and experimental results show dramatic heat transfer enhancement by using a vortex generator and nanofluids, simultaneously accomplished with a moderate increase in the friction factor. A low deviation has been seen between the present numerical and experimental results.     

2 kW半导体激光加工光源

针对激光加工在金属材料焊接、熔覆、表面硬化等工业领域的应用,考虑到半导体激光器体积和重量小、效率高、免维护、成本低以及波长较短等特点,设计了功率达2 kW的半导体激光加工光源。在大通道工业水冷条件下,采用48只出射波长分别为808,880,938,976 nm的传导冷却半导体激光阵列作为发光单元,最终研制出了2 218 W高亮度光纤耦合模块。此高亮度模块可以实现柔性加工,直接应用于金属材料焊接、熔覆、表面合金化等工业领域,对于半导体激光器在工业领域的应用具有重要意义。