化学类拔尖学生培养与高校青年教师成长协同发展实践*

在高等教育大众化的背景下,通过教学改革培养高素质的拔尖人才已显得非常重要。介绍一种以新入职的青年教师为实施主体的“理论课助教+实验课教学+科研训练”相结合的教学形式。通过连续、跟踪式的教学,不但可以选拔、培养出拔尖的化学类本科生,而且能够促进新入职的青年教师快速成长进步,起到“教学相长”的作用。     

线上线下混合式实验教学模式的改革与探索

大学化学实验课程是培养材料、化学、化工等专业人才应用基本操作和理论解决实际问题的综合性实践训练环节。文章探讨了当前大学化学实验发展由于受到仪器设备大型化、专业化、成本大、更新快等因素限制出现瓶颈,设计了线上线下混合实验教学模式,进行相应的软硬件建设,并开展线上线下混合式实验教学模式的改革与探索。该教学模式具有良好的教学效果,并且可复制可推广,为创新人才的培养和实验教学的创新提供了有益的借鉴。     

Coupling characteristics of laterally coupled gratings with slots

Laterally-coupled ridge-waveguide distributed feedback lasers fabricated without epitaxial regrowth steps have the advantages of process simplification and low cost. We present a laterally coupled grating with slots. The slots etched between the ridge and grating area are designed to suppress the lateral diffusion of carriers and to reduce the influence of the aspect-ratio-dependent-etching effect on the grating morphology in the etching process. Moreover, the grating height in this structure can be decreased to lower the aspect ratio significantly, which is advantageous over the conventional laterally coupled ridge waveguide gratings. The effects of five main structural parameters on the coupling characteristics of gratings are studied by MODE Solutions. It is found that varying the lateral width of the grating can be used as an effective way to tune the coupling strength; narrow slots (100 nm and 300 nm) and wide ridge (2 μm-4 μm) promote the stability of grating coupling coefficient and device performance. It is important to note that the grating bottom should be fabricated precisely. The comparative study of carrier distribution and mode field distribution shows that the introduction of narrow slots can strengthen the competitive advantage and stability of the fundamental mode.     

Asymmetric nonlinear-mode-conversion in an optical waveguide withPT symmetry

Asymmetric mode transformation in waveguide is of great significance for on-chip integrated devices with one-way effect, while it is challenging to achieve asymmetric nonlinear-mode-conversion (NMC) due to the limitations imposed by phase-matching. In this work, we theoretically proposed a new scheme for realizing asymmetric NMC by combining frequency-doubling process and periodic PT symmetric modulation in an optical waveguide. By engineering the one-way momentum from PT symmetric modulation, we have demonstrated the unidirectional conversion from pump to second harmonic with desired guided modes. Our findings offer new opportunities for manipulating nonlinear optical fields with PT symmetry, which could further boost more exploration on on-chip nonlinear devices assisted by non-Hermitian optics.     

Relationship between the spatial position of the seed and growth mode for single-crystal diamond grown with an enclosed-type holder

The relationship between the spatial position of the diamond seed and growth mode is investigated with an enclosed-type holder for single-crystal diamond growth using the microwave plasma chemical vapor deposition epitaxial method. The results demonstrate that there are three main regions by varying the spatial position of the seed. Due to the plasma concentration occurring at the seed edge, a larger depth is beneficial to transfer the plasma to the holder surface and suppress the polycrystalline diamond rim around the seed edge. However, the plasma density at the edge decreases drastically when the depth is too large, resulting in the growth of a vicinal grain plane and the reduction of surface area. By adopting an appropriate spatial location, the size of single-crystal diamond can be increased from 7 mm × 7 mm × 0.35 mm to 8.6 mm × 8.6 mm × 2.8 mm without the polycrystalline diamond rim.     

Preparation of a monolithic column with a mixed‐mode stationary phase of reversed‐phase/hydrophilic interaction for capillary liquid chromatography

A monolithic capillary column with a mixed‐mode stationary phase of reversed‐phase/hydrophilic interaction chromatography was prepared for capillary liquid chromatography. The monolith was created by an in‐situ copolymerization of a homemade monomer N,N‐dimethyl‐N‐acryloxyundecyl‐N‐(3‐sulfopropyl) ammonium betaine and a crosslinker pentaerythritol triacrylate in a binary porogen agent consisting of methanol and isopropanol. The functional monomer was designed to have a highly polar zwitterionic sulfobetaine terminal group and a hydrophobic long alkyl chain moiety. The composition of the polymerization solution was systematically optimized to permit the best column performance. The columns were evaluated by using acidic, basic, polar neutral analytes, as well as a set of alkylbenzenes and Triton X100. Very good separations were obtained on the column with the mixed‐mode stationary phase. It was demonstrated that the mixed‐mode stationary phase displayed typic dual retention mechanisms of reversed‐phase/hydrophilic interaction liquid chromatography depending on the content of acetonitrile in the mobile phase. The method for column preparation is reproducible.     

基于改进粒子群的薄壁变截面刚架临界载荷优化算法

针对大型变截面薄壁结构的稳定问题，以一类任意约束对称结构受非对称载荷的单跨刚架为研究对象，结构拆分为相关铁木辛柯（Timoshenko）梁，结合差分原理和最优化方法，以每段刚架的每个离散点挠度、临界载荷、轴力、剪力和梁端弯矩为设计变量，建立求解满足边界条件的非线性差分方程模型，提出基于优胜劣汰粒子更新的粒子群（IPSO）临界载荷优化算法。运用JAVA编程语言编制对应优化程序，分析典型算例并核实ABAQUS仿真结果。研究表明，本文提出的优化算法获得了有效的变形位型和高精度的临界载荷计算，能更好地描述刚架受力下位型和载荷的力学关系，进一步为工程设计与分析提供支持。     

Sliding mode control for a diffuse interface tumor growth model coupling a Cahn–Hilliard equation with a reaction–diffusion equation

We consider the sliding mode control (SMC) problem for a diffuse interface tumor growth model coupling a Cahn–Hilliard equation with a reaction–diffusion equation perturbed by a maximal monotone nonlinearity. We prove existence and regularity of strong solutions and, under further assumptions, a uniqueness result. Then, we show that the chosen SMC law forces the system to reach within finite time a sliding manifold that we chose in order that the tumor phase remains constant in time.     

Dynamic and buckling analysis of polymer hybrid composite beam with variable thickness

This work deals with a study of the dynamic and buckling analysis of polymer hybrid composite(PHC) beam. The beam has variable thickness and is reinforced by carbon nanotubes(CNTs) and nanoclay(NC) simultaneously. The governing equations are derived based on the first shear deformation theory(FSDT). A three-phase HalpinTsai approach is used to predict the mechanical properties of the PHC. We focus our attention on the effect of the simultaneous addition of NC and CNT on the vibration and buckling analysis of the PHC beam with variable thickness. Also a comparison study is done on the sensation of three impressive parameters including CNT, NC weight fractions, and the shape factor of fillers on the mechanical properties of PHC beams,as well as fundamental frequencies of free vibrations and critical buckling load. The results show that the increase of shape factor value, NC, and CNT weight fractions leads to considerable reinforcement in mechanical properties as well as increase of the dimensionless fundamental frequency and buckling load. The variation of CNT weight fraction on elastic modulus is more sensitive rather than shear modulus but the effect of NC weight fraction on elastic and shear moduli is fairly the same. The shape factor values more than the medium level do not affect the mechanical properties.     

The Application of Fractal Transform and Entropy for Improving Fault Tolerance and Load Balancing in Grid Computing Environments

This paper applies the entropy-based fractal indexing scheme that enables the grid environment for fast indexing and querying. It addresses the issue of fault tolerance and load balancing-based fractal management to make computational grids more effective and reliable. A fractal dimension of a cloud of points gives an estimate of the intrinsic dimensionality of the data in that space. The main drawback of this technique is the long computing time. The main contribution of the suggested work is to investigate the effect of fractal transform by adding R-tree index structure-based entropy to existing grid computing models to obtain a balanced infrastructure with minimal fault. In this regard, the presented work is going to extend the commonly scheduling algorithms that are built based on the physical grid structure to a reduced logical network. The objective of this logical network is to reduce the searching in the grid paths according to arrival time rate and path’s bandwidth with respect to load balance and fault tolerance, respectively. Furthermore, an optimization searching technique is utilized to enhance the grid performance by investigating the optimum number of nodes extracted from the logical grid. The experimental results indicated that the proposed model has better execution time, throughput, makespan, latency, load balancing, and success rate.