Sensitivity improvement of aluminum-based far-ultraviolet nearly guided-wave surface plasmon resonance sensor

An aluminum (Al) based nearly guided-wave surface plasmon resonance (NGWSPR) sensor is investigated in the far-ultraviolet (FUV) region. By simultaneously optimizing the thickness of Al and dielectric films, the sensitivity of the optimized Al-based FUV-NGWSPR sensor increases from 183°/RIU to 309°/RIU, and its figure of merit rises from 26.47 RIU^-1 to 32.59 RIU^-1 when the refractive index of dielectric increases from 2 to 5. Compared with a traditional FUV-SPR sensor without dielectric, the optimized FUV-NGWSPR sensor can realize simultaneous improvement of sensitivity and figure of merit. In addition, the FUV-NGWSPR sensor with realistic materials (diamond, Ta₂O₅, and GaN) is also investigated, and 137.84%, 52.70%, and 41.89% sensitivity improvements are achieved respectively. This work proposes a method for performance improvement of FUV-SPR sensors by exciting nearly guided-wave, and could be helpful for the high-performance SPR sensor in the short-wavelength region.     

一种非正交对称条带束流位置监测器设计

介绍了一种条带束流位置监测器(BPM)的设计与仿真方法。在国家同步辐射实验室"太赫兹近场高通量材料物性测试系统"工程项目中,针对波荡器出口处真空室非正交对称性的问题,设计了矩形真空室和跑道形真空室下的两种非正交对称性条带BPM,并与传统的圆形真空室下条带BPM进行对比。基于边界元法,利用MATLAB软件分别对三种真空室下的条带BPM进行建模和仿真。仿真结果表明:相对于传统的圆形真空室下条带BPM,矩形和跑道形真空室下条带BPM灵敏度提高了30%,阻抗匹配误差相对降低了20%,束流位置拟合误差降低了80%。考虑加工精度,矩形真空室下的条带BPM更适用于该工程。     

光寻址电位传感器的正交相位检波检测方法

光寻址电位传感器的幅度检测方法易受噪声干扰,灵敏度差,信噪比和精度低,且受调制光源的影响较大,影响检测结果的准确性.为此提出了一种基于正交相位检波的光寻址电位传感器检测方法.该方法是将光寻址电位传感器的输出光电流信号分别与两路正交信号相乘,通过低通滤波提取直流分量并相除,即可得到光寻址电位传感器的输出信号相位信息.与已有的光寻址电位传感器相位检测方法相比,该方法具有算法复杂度低、实时性高的优点.实验研究了调制光源光强对光寻址电位传感器幅度检测和相位检测的影响,对比分析了光寻址电位传感器的传统幅度检测方法与正交相位检波检测方法对pH检测的灵敏度、线性度及信噪比.结果表明,相比于幅度检测方法,调制光源光强对光寻址电位传感器的相位检测影响更小,在频率为10 kHz,pH的范围为1.68~10.01的情况下,相位检测方法比幅度检测方法测得的灵敏度增加了7 mV/pH,精度提高了14.9 mpH,非线性误差减小了0.003%,均方差减少了0.1051×10^-5,信噪比增加了8.2827 dB.该方法特别适用于弱光下的光寻址电位传感器检测.     

消光式核壳二聚体传感器的设计与光谱特性分析

根据ITO/Au纳米核壳二聚体粒子在生物医学领域的应用合理性,设计了一种实时检测生物液体的核壳二聚体探针消光式传感器;由偶极子理论推导出输出波长与外界环境折射率关系;利用MATLAB设计ITO/Au纳米核壳二聚体粒子结构;采用软件DDSCAT7.3结合离散偶极近似法,利用二聚体有效半径模拟计算了300~950nm可见光到红外光波段不同核壳比、二聚体间距、以及不同介质折射率的消光光谱;根据传感芯片折射率与偶极共振、耦合八级共振的响应关系得出ITO/Au二聚体的折射率灵敏特性。与传统Ag/Au核壳纳米粒子相比,ITO/Au纳米核壳二聚体结构引入了可作为传感芯片灵敏性自参考参数的耦合八级共振峰,同时ITO/Au二聚体结构的折射率灵敏度可达到419nm/RIU。这些工作及其结果对制作消光式传感器具有重要的意义。     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

Rate sensitivity and deformation mechanism of semi-crystalline polymers during instrumented indentation

Instrumented indentation tests using both constant loading rate (CLR) and continuous stiffness measurement (CSM) operation modes were performed to investigate the deformation mechanism and their sensitivity to the deformation rate in semi-crystalline polymers through the quantitative analysis of load-depth loading and unloading curves. The strain rate was constant during the CSM tests, while the strain rate decreased with the increasing of loading time in CLR tests. The mechanical response mechanism of the semi-crystalline polymers to these tests was very complicated because of the combined effects of strain-hardening in the crystal phase and strain-softening in the amorphous phase. Results show that the loading index m reflects the strain-hardening or strain-softening response during indentation. When m > 2, the mechanical response was due to the strain-hardening, and when m < 2, the response was due to strain-softening. A method based on the measured contact hardness was proposed to obtain the unloading stiffness, and the other mechanical parameters could then be determined according to the unloading stiffness.     

一种基于自适应单元删除率的BESO方法

在ESO中采用动态删除率能有效地提高优化效率和稳定性，但现有的动态删除率策略都含有经验参数，确定删除率的过程较为复杂。本文提出了一种用于BESO的无经验参数自适应单元删除率确定方法。通过分析单元删除率对优化稳定性的影响，得到了结构优化过程中单元删除率的理想变化规律和单元灵敏度均匀化信息对删除率的影响情况，并据此分析了经验参数引入的原因，从而构造了评价单迭代步的单元灵敏度均匀化程度指标。然后，基于单迭代步的单元灵敏度均匀化程度指标，构造了全部迭代步信息下的单元灵敏度均匀化程度相对指标，结合单元删除率的推荐范围值，给出了一种自适应于结构优化进程的单元删除率自适应函数。最后，给出了基于自适应单元删除率的BESO方法实现流程。经典算例的结果对比说明，本文方法在保证优化质量相近的情况下，具有更好的优化效率和稳定性。     

Tunable and highly sensitive temperature sensor based on graphene photonic crystal fiber

Optical fiber temperature sensors have been widely employed in enormous areas ranging from electric power industry, medical treatment, ocean dynamics to aerospace. Recently, graphene optical fiber temperature sensors attract tremendous attention for their merits of simple structure and direct power detecting ability. However, these sensors based on transfer techniques still have limitations in the relatively low sensitivity or distortion of the transmission characteristics, due to the unsuitable Fermi level of graphene and the destruction of fiber structure, respectively. Here, we propose a tunable and highly sensitive temperature sensor based on graphene photonic crystal fiber (Gr-PCF) with the non-destructive integration of graphene into the holes of PCF. This hybrid structure promises the intact fiber structure and transmission mode, which efficiently enhances the temperature detection ability of graphene. From our simulation, we find that the temperature sensitivity can be electrically tuned over four orders of magnitude and achieve up to ～ 3.34×10^-3 dB/(cm·℃) when the graphene Fermi level is ～ 35 meV higher than half the incident photon energy. Additionally, this sensitivity can be further improved by ～ 10 times through optimizing the PCF structure (such as the fiber hole diameter) to enhance the light-matter interaction. Our results provide a new way for the design of the highly sensitive temperature sensors and broaden applications in all-fiber optoelectronic devices.     

A New Fluorescence Turn-On Probe for Aluminum(III) with High Selectivity and Sensitivity,and its Application to Bioimaging

The development of novel selective probes with high sensitivity for the detection of Al³⁺ is widely considered an important research goal due to the importance of such probes in medicine, living systems and the environment. Here, we describe a new fluorescent probe, N′-(4-diethylamino-2-hydroxybenzylidene)-2-hydroxybenzohydrazide (1), for Al³⁺. Probe 1 was evaluated in a solution of acetonitrile/water (1:1 v/v). Compared with previously reported probes for Al³⁺, probe 1 can be synthesized easily and in high yield. A Job plot confirmed that probe 1 is able to complex Al³⁺ in a 1:1 ratio, and the binding constant was determined to be 4.25×10⁸ m⁻¹. Moreover, the detection limit was as low as 6.7×10⁻⁹ m, suggesting that probe 1 has a high sensitivity. Common coexistent metal ions, such as K⁺, Co²⁺, Ca²⁺, Ba²⁺, Ni²⁺, Pb²⁺, Hg²⁺, Ce²⁺, Zn²⁺, Cd²⁺, Fe³⁺, showed little or no interference in the detection of Al³⁺ in solution, demonstrating the high selectivity of the probe. Finally, the ability of probe 1 to act as a fluorescent probe for Al³⁺ in living systems was evaluated in Gram-negative bacteria, Escherichia coli, and confocal laser scanning microscopy confirmed its utility. The results of this study suggest that 1 has appropriate properties to be developed for application as a fluorescent probe of Al³⁺ for use in biological studies.     

双靶向CdTe量子点的制备及其在细胞标记中的应用

以巯基乙酸和巯基乙酰肼为稳定剂,制备了酸度敏感型CdTe量子点。经与抗体链接,该量子点具备酸度敏感、免疫识别双重靶向功能。经荧光光谱分析、透射电镜图像及细胞免疫成像证明,抗体已成功链接于量子点表面,且该量子点具有酸度敏感及抗体识别的双重靶向功能,可以实现对肿瘤细胞的特异性标记。