石英晶体板非线性高频振动的拓展伽辽金法分析

针对考虑几何和材料非线性的石英晶体板厚度剪切振动和弯曲振动的方程组,利用扩展伽辽金法对该方程组进行转化和求解,分别获得了强烈耦合的厚度剪切振动模态和弯曲振动模态的频率响应关系,绘制了不同振幅比和不同驱动电压影响下的频率响应曲线图。数值计算结果表明可以选取石英晶片的最佳长厚比尺寸来避免两种模态的强烈耦合。驱动电压的变化将引起石英晶体谐振器厚度剪切振动频率的明显改变,必须将振动频率的漂移值控制在常用压电声波器件的允许值之内。扩展伽辽金法对石英晶体板非线性振动方程组的求解为非线性有限元分析和偏场效应分析奠定了基础。     

Effect of oxygen on regulation of properties of moderately boron-doped diamond films

Regulation of oxygen on properties of moderately boron-doped diamond films is fully investigated. Results show that, with adding a small amount of oxygen (oxygen-to-carbon ratio < 5.0%), the crystal quality of diamond is improved, and a suppression effect of residual nitrogen is observed. With increasing ratio of O/C from 2.5% to 20.0%, the hole concentration is firstly increased then reduced. This change of hole concentration is also explained. Moreover, the results of Hall effect measurement with temperatures from 300 K to 825 K show that, with adding a small amount of oxygen, boron and oxygen complex structures (especially B₃O and B₄O) are formed and exhibit as shallow donor in diamond, which results in increase of donor concentration. With further increase of ratio of O/C, the inhibitory behaviors of oxygen on boron leads to decrease of acceptor concentration (the optical emission spectroscopy has shown that it is decreased with ratio of O/C more than 10.0%). This work demonstrates that oxygen-doping induced increasement of the crystalline and surface quality could be restored by the co-doping with oxygen. The technique could achieve boron-doped diamond films with both high quality and acceptable hole concentration, which is applicable to electronic level of usage.     

Dynamic Modeling of the Feed Drive System of a CNC Metal Cutting Machine

Studying the vibrational behavior of feed drive systems is important for enhancing the structural performance of computer numerical control (CNC) machines. The preload on the screw and nut position have a great influence on the vibration characteristics of the feed drive as two very important operational conditions. Rotational acceleration of the screw also affects the performance of the CNC feed drive when machining small parts. This paper investigates the influence of preload and nut position on the vibration characteristics of the feed drive system of a CNC metal cutting machine in order to be able to eliminate an observed resonance occurred at high rotational speeds of the screw, corresponding to high feed rates. Additionally, rational structural parameters of the feed drive system are selected in order to increase the rotational acceleration for improving the performance of the CNC machine. Experiments and analyses showed that by selecting specific parameters of feed drive system and simultaneously applying a certain value of preload, a 97% increase in rotational acceleration and 30% time reduction considering the vibration resistance at high rotational speeds can be achieved.     

碳纳米管增强型复合材料功能梯度板的自由振动模型与尺度效应

基于一种新的各向异性修正偶应力理论，建立了碳纳米管增强复合材料功能梯度板的自由振动模型。该模型能够描述尺度效应，且仅包含一个尺度参数。基于一阶剪切变形理论和哈密顿原理推演了板的运动微分方程，并以四边简支板为例给出了自振频率的解析解。讨论了板的几何尺寸、碳纳米管体分比含量和分布方式等因素对板的自振频率的影响。结果表明，本文模型所预测的板的自振基频总是高于经典弹性理论的Mindlin板模型的预测结果，两者间的差异在板的几何尺寸接近尺度参数的值时非常明显，且会随着板的几何尺寸的增大而逐渐消失。     

REBOUNDING OF GALILEAN CANNON FROM A RIGID WALL1)

研究了Galilean炮——即若干个直径递增的弹性球组成的球链---撞击刚性壁回弹的问题。采用三种力学模型：分离刚体的多次"弹性"碰撞、多刚体的接触碰撞、以及有限元模拟，对球链撞击问题进行了分析，旨在给出碰撞结束后末端小球的飞离速度与入射速度的比值。研究表明：球链碰撞反弹后将会散开，末端小球的飞离速度明显大于球链入射速度；当入射球链间存在间隙时，末端小球的速度增幅更加明显。通过实验展现了这种末端小球回弹速度增加的现象。     

基于SPH/FEM方法的浅水冲击喷溅及其抑制结构研究

物体浅水冲击会造成结构响应和自由液面的剧烈喷溅,以往的研究多集中在物体受水的冲击响应方面,而对浅水层受物体冲击引起的剧烈喷溅问题及其喷溅抑制结构的相关研究很少。本文基于SPH/FEM耦合方法对浅水冲击的液体喷溅特性开展研究。首先,计算了刚性长方体结构的冲击喷溅,与文献中准二维溅水试验结果进行了比较,将浅水喷溅分为初始喷溅、二次喷溅和底部射流三部分。分别研究了各部分喷溅的形成机理,指出二次喷溅由结构对水层的挤压和底部射流的能量传递共同引起,并分析了水深对二次喷溅的影响规律。其次,对喷溅抑制结构的机理做了数值研究,发现拱形翻边构型可以抑制初始喷溅,但不能有效降低二次喷溅。最后,提出了一种带凹槽和阻水边条的新型翻边构型,对二次喷溅具有更好的抑制效果。     

多层复合壳体三维振动分析的谱——微分求积混合法

对于较厚的多层复合壳体,其振动位移沿厚度方向呈锯齿形变化且层间剪切和拉、压应力呈三维耦合状态,采用传统的等效单层理论分析已不能满足精度要求. 建立不受结构厚度、铺层材料性质和铺层方式限制的三维分析方法具有重要的研究价值. 本文以独立铺层为建模对象,结合广义谱方法与微分求积技术建立了一种适用一般边界条件和铺层方式的多层复合壳体三维分析新方法——谱--微分求积混合法. 该方法应用三维弹性理论对独立铺层进行精确建模,有效克服了二维简化理论对横向变形以及层间应力估计不确切的缺点;引入微分求积技术对铺层进行数值离散,将三维偏微分问题转化为二维偏微分问题,降低了求解维度和难度;应用广义谱方法近似地表述离散计算面上的场变量,将获取的二维偏微分方程转化为以场变量谱展开系数为未知量的线性代数方程组,避免了对超越方程的求解. 数值验证结果表明该方法收敛性好,计算精度高.      

INFLUENCE OF FRICTION ON THE MOTION OF BASE WITH AN ECCENTRIC ROTOR

偏心转子惯性力引起的底座运动受到地面摩擦的影响，与光滑情形的理论结果存在定性差异。转子逆时针匀速旋转的惯性力若小于构件总重，则底座随摩擦因子增加而出现连续、一次停顿和两次停顿的振动及完全静止的4种状态。因惯性力对正压力及摩擦力的影响，底座在连续及一次停顿的振动时右向位移较大；而底座跳起时如``蛤蟆夯'则整体向左移动。     

Biological and catalytic evaluation of Ru(II)‐p‐cymene complexes of Schiff base ligands: Impact of ligand appended moiety on photo‐induced DNA and protein cleavage,cytotoxicity and C‐H activation

Two organometallic Ru(II)‐p‐cymene complexes of the type [Ru(η⁶‐p‐cymene)(L)Cl]PF₆ 1 and 2 , where L is N,N‐bis(4‐isopropylbenzylidene)ethane‐1,2‐diamine (bien, L1 ) or N,N‐bis (pyren‐2‐ylmethylene)ethane‐1,2‐diamine (bpen, L2 ) have been prepared and characterized well. Because of appended pyrenyl groups in coordinated bpen ligand, the complex 2 exhibits higher DNA and protein binding than complex 1 in which isopropylbenzyl groups are incorporated. Interestingly, the luminescent characteristic complex 2 is unique in displaying DNA cleavage after light activation by UVA light at 365 nm through oxygen dependent mechanism. AFM analysis attests the photo‐induced DNA fragmentation ability of complex 2 . Also, the complex 2 cleaves the protein after light exposure in a non‐specific manner suggesting that it can act as a protein photo cleaving agent. In contrast to the trend of DNA and protein interaction of complexes, the complex 1 exhibits cytotoxic activity against human breast carcinoma ( MCF‐7 ) and liver carcinoma ( HepG2 ) with potency higher than that of complex 2 due to enhanced hydrophobicity of isopropyl groups present in p‐cymene and bien ligands. Indeed, complex 2 is inactive against MCF‐7 and HepG2 cancer cell lines even up to 200 μM concentration. The AO/EB staining assay reveals that the complex 1 is able to induce late apoptotic mode of cell death in breast cancer cells, which is further confirmed by inter‐nucleosomal DNA cleavage. Furthermore, the complexes 1 and 2 are evaluated for their catalytic activities and found to be working well for the β‐carboline directed C–H arylation to afford the desired products in good yield (40–47%).     

Enhanced interfacial adhesion between PMMA and carbon fiber by graphene oxide coating

The purpose of this study is to increase the interfacial properties in PMMA/carbon fiber (PMMA/CF) composites Graphene oxide (GO) and brached polyethyleneimine were coated onto the surface of carbon fiber by layer-by-layer assembly in this work. Compared with the origin PMMA/CF composite, the composites reinforced by PMMA/CF–GO showed significant enhancement in interFacial shear strength (IFSS). The improved fiber–matrix adhesion was proved by fracture morphology observation of scanning electron microscopy and almost unaffected mechanical properties of the fiber itself during the coating process. The optimal assembly time was found to be 10 for enhancing the overall composite mechanical performance.