基于应变梯度理论的微尺度蜂窝等效模量计算方法

本文提出了一种新的能够计及尺度效应的微纳米蜂窝等效模量的计算方法。将一种单参数应变梯度理论引入到本构方程当中,并基于能量等效原理推导了蜂窝面内等效模量地计算公式。算例分析表明,本文方法能够有效地计及尺度效应对蜂窝等效模量的影响。尺度效应与胞壁厚度和长度的值都有关,当胞壁厚度较小时,尺度效应显著,本文方法预测的模量会明显高于传统方法;而当胞壁厚度较大时,尺度效应变得微弱乃至可以忽略不计。但如果胞壁的长度/厚度比很大,则面内等效模量会趋近于0,此时是否考虑尺度效应意义不大。     

硫化丁苯橡胶纳观界面耐磨机理及参数影响分析

硫化橡胶因其良好的力学和物理化学性能而被广泛作为摩擦副的基础材料. 本文提出了一种硫化交联算法, 实现了C—C键的硫化互交联和自交联, 构建了硫化丁苯橡胶的分子动力学磨损模型, 从微观摩擦学的角度阐明了硫化交联结构对改善丁苯橡胶磨损性能的机理, 研究了不同界面参数对硫化橡胶微观磨损性能的影响. 结果发现 硫化使丁苯橡胶分子链的界面黏附能力和活动能力更弱, 拉伸和解缠能力更低, 磨损过程中界面累积能量更低, 更不容易脱离橡胶基体, 因此可以表现出更好的摩擦学性能, 更强的抗磨损性能; 随着速度的增大, 硫化橡胶的磨损率降低, 与宏观实验结果一致, 原因是硫化橡胶的原子分布函数和相互作用能随着速度增大而降低, 说明橡胶分子链的黏附能力和活动能力随着速度增加趋弱, 温升更低, 导致较低的磨损率; 压入深度对磨损率的影响规律则呈现相反的结果和趋势.     

砂岩方梁断裂过程区范围的实验确定方法

裂纹前端的断裂过程区是引起岩石非线性断裂及尺寸效应的主要原因。利用数字图像相关技术对砂岩开展了三点弯曲梁实验,获得观测区域高精度的全场位移和应变数据,根据断裂韧带区域水平位移和水平应变的分布特征,结合裂尖岩石颗粒变化的微观分析,提出采用裂纹尖端水平位移波动性和水平应变突变性所得到的波动系数和水平应变突变值,确定断裂过程区形状和临界尺寸的方法。结果表明:砂岩断裂过程区的形状为不规则的狭长带状区域,断裂过程区的临界长度为11~13mm,临界宽度为1.58~2.36mm。断裂过程区区域内形变在趋向裂尖时呈指数增加,但其单位区域内的形变增量呈波动状态。该方法能够更加准确判断岩石断裂过程区的范围,有助于分析岩石的非线性断裂特性。     

基于串联两阶段网络DEA模型的供应链规模收益分析

数据包络分析(DEA)是评价供应链系统(Supply chain system)间相对有效性的一种重要的工具,但是传统的DEA不考虑供应链的内部结构,对系统效率评价偏高;而本文所研究两阶段串联供应链系统,考虑把部分中间产品作为最终产品输出,增加额外中间投入的情形.基于所提出的供应链系统结构,本文建立相应的串联结构下的网络DEA模型,并针对所建立模型进行相关理论的研究,给出了串联结构下的生产可能集和规模收益情况判定方法.最后,进行数值实验,以验证我们提出的结论.     

水力劈裂问题的态型近场动力学建模

将态型近场动力学理论引入水力劈裂问题的模拟。构建了能反映岩土类材料准脆性断裂特征的态型近场动力学本构模型,并在物质点间相互作用力模型中加入等效水压力项,以实现在新生裂纹面上跟踪施加水压力。同时,考虑裂纹面间的接触,引入物质点间的短程排斥力作用,并设计了相应的接触算法。通过自编程序将模型和算法应用于含初始裂纹、不含初始裂纹以及含坝基软弱结构面的混凝土重力坝在高水头作用下的水力劈裂过程模拟,并与扩展有限元等模拟结果对比,验证了本文模型和算法的可行性和准确性。     

A unified theory for brittle and ductile shear mode fracture

A unified theory captures both brittle and ductile fracture. The fracture toughness is proportional to the applied stress squared and the length of the crack. For purely brittle solids, this criterion is equivalent to Griffith's theory. In other cases, it provides a theoretical basis for the Irwin-Orowan formula. For purely ductile solids, the theory makes direct contact with the Bilby-Cottrell-Swinden model. The toughness is highest in ductile materials because the shielding dislocations in the plastic zone provide additional resistance to crack growth. This resistance is the force opposing dislocation motion, and the Peach-Koehler force overcomes it. A dislocation-free zone separates the plastic zone from and the tip of the crack. The dislocation-free zone is finite because molecular forces responsible for the cohesion of the surfaces near the crack tip are not negligible. At the point of crack growth, the length of the dislocation-free zone is constant and the shielding dislocations advance in concert. As in Griffith's theory, the crack is in unstable equilibrium. The theory shows that a dimensionless variable controls the elastoplastic behaviour. A relationship for the size of the dislocation-free zone is derived in terms of the macroscopic and microscopic parameters that govern the fracture.     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

不同声音偏好的游客声景观主观评价差异——以丽江大研古镇为例*

古镇作为集自然景观与人文景观一体的景区，具有丰富的声音类型。本研究以大研古镇为例，通过实地调研探究不同声音偏好的游客对古镇声景观的主观评价差异。基于游客的声音偏好，将游客分为偏爱自然声和偏爱人工声两大类。通过因子分析提取游客声景观主观评价的5个主因子：大小、音质、效价、偏好和唤醒。进一步分析发现，这5个因子具有一定的层级性，其中从大小到唤醒代表声景观评价从声音的物理属性向声音的联想评价逐级提升。其中在低层级评价(大小、音质)中，偏好自然声的游客和偏好人工声的游客无显著差异，低层级评价具有稳定性；而在高层级评价(效价、偏好和唤醒)中，偏好人工声的游客更关注古镇声景观的淳朴性和遗产性。因此，游客对声景观的主观评价可视为一种指标，判断景区声景所处的评价阶段，从而为景区声景观改善提供更有针对性的建议。     

稳定分层湍流中逆梯度输运的关联分析研究

本文采用关联分析方法研究了稳定温度分层湍流中的结构特性、输运特性，以及热量、动量逆梯度输运现象的尺度效应及其参数演化．首先采用大涡模拟方法对稳定分层湍流中的结构特性和输运特性进行了分析，将逆梯度输运发生的时间尺度作为已知条件，结合关联量分析方法在波数空间中的解析解，对逆梯度输运现象的尺度效应进行了分析研究．结果发现，稳定分层强度较大的流动中发生垂向热量及动量逆梯度输运现象，发生的结构尺度与关联分析所发现垂向热量、动量逆梯度输运的波数形成了呼应．随着分层强度增加，热量、动量的输运强度均受抑制，与逆梯度输运关联的流场结构尺度减小，同样的效应也发生在流场结构向下游演化的过程中．     

Chemorheology investigation of a glassy epoxy thermoset on tensile plastic flow and fracture morphology

Reproducible and uncharacteristic tensile stress–strain behavior of cured glassy epoxy‐amine networks produces distinctive fracture surfaces. Test specimens exhibiting plastic flow result in mirror‐like fracture surfaces, whereas samples that fail during yield or strain softening regions possess nominal mirror‐mist‐hackle topography. Atomic force microscopy and scanning electron microscopy reveal branched nodule morphologies in the 50‐nm size scale that may be responsible for the unusual tensile properties. Current hypothesis is that plastic flow of the glassy thermoset occurs through the existence and deformation of these nodular nanostructures. The thermal cure profile of the epoxy‐amine thermoset affects the size and formation of the nodular nanostructure. Eliminating vitrification during thermoset polymerization forms a more continuous phase, reduction in size of the nodules, and eliminates the capacity of the material to yield in plastic flow. This maximizes nanostructure connectivity of the glassy epoxy‐amine thermoset and reduces strain to failure significantly. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1333–1344.