基于改进粒子群的薄壁变截面刚架临界载荷优化算法

针对大型变截面薄壁结构的稳定问题，以一类任意约束对称结构受非对称载荷的单跨刚架为研究对象，结构拆分为相关铁木辛柯（Timoshenko）梁，结合差分原理和最优化方法，以每段刚架的每个离散点挠度、临界载荷、轴力、剪力和梁端弯矩为设计变量，建立求解满足边界条件的非线性差分方程模型，提出基于优胜劣汰粒子更新的粒子群（IPSO）临界载荷优化算法。运用JAVA编程语言编制对应优化程序，分析典型算例并核实ABAQUS仿真结果。研究表明，本文提出的优化算法获得了有效的变形位型和高精度的临界载荷计算，能更好地描述刚架受力下位型和载荷的力学关系，进一步为工程设计与分析提供支持。     

Dynamic and buckling analysis of polymer hybrid composite beam with variable thickness

This work deals with a study of the dynamic and buckling analysis of polymer hybrid composite(PHC) beam. The beam has variable thickness and is reinforced by carbon nanotubes(CNTs) and nanoclay(NC) simultaneously. The governing equations are derived based on the first shear deformation theory(FSDT). A three-phase HalpinTsai approach is used to predict the mechanical properties of the PHC. We focus our attention on the effect of the simultaneous addition of NC and CNT on the vibration and buckling analysis of the PHC beam with variable thickness. Also a comparison study is done on the sensation of three impressive parameters including CNT, NC weight fractions, and the shape factor of fillers on the mechanical properties of PHC beams,as well as fundamental frequencies of free vibrations and critical buckling load. The results show that the increase of shape factor value, NC, and CNT weight fractions leads to considerable reinforcement in mechanical properties as well as increase of the dimensionless fundamental frequency and buckling load. The variation of CNT weight fraction on elastic modulus is more sensitive rather than shear modulus but the effect of NC weight fraction on elastic and shear moduli is fairly the same. The shape factor values more than the medium level do not affect the mechanical properties.     

The Application of Fractal Transform and Entropy for Improving Fault Tolerance and Load Balancing in Grid Computing Environments

This paper applies the entropy-based fractal indexing scheme that enables the grid environment for fast indexing and querying. It addresses the issue of fault tolerance and load balancing-based fractal management to make computational grids more effective and reliable. A fractal dimension of a cloud of points gives an estimate of the intrinsic dimensionality of the data in that space. The main drawback of this technique is the long computing time. The main contribution of the suggested work is to investigate the effect of fractal transform by adding R-tree index structure-based entropy to existing grid computing models to obtain a balanced infrastructure with minimal fault. In this regard, the presented work is going to extend the commonly scheduling algorithms that are built based on the physical grid structure to a reduced logical network. The objective of this logical network is to reduce the searching in the grid paths according to arrival time rate and path’s bandwidth with respect to load balance and fault tolerance, respectively. Furthermore, an optimization searching technique is utilized to enhance the grid performance by investigating the optimum number of nodes extracted from the logical grid. The experimental results indicated that the proposed model has better execution time, throughput, makespan, latency, load balancing, and success rate.     

基于SWT方法的钢绞线索微动疲劳特性分析

为得到钢绞线索丝间接触区的应力场分布并预测微动疲劳裂纹萌生位置和微动疲劳寿命，本文利用参数化方法建立了精细化的钢绞线拉索有限元模型，包括整索模型和不同层丝间接触区域的局部精细化子模型．分析了钢绞线索在两种交变荷载工况下的应力场变化情况，并基于多轴疲劳SWT(Smith-Watson-Topper)临界平面法进行了疲劳特性分析和疲劳寿命预测．主要结论如下：钢绞线索内接触区边缘处的微动幅值较大，中心处几乎没有相对滑动，微动疲劳的初始裂纹萌生点位于接触区域边缘；经不同区域子模型分析比较，在轴向循环荷载作用下，外层钢丝的接触区域比内层钢丝更易发生微动疲劳损伤；在横向位移循环荷载作用下，同层钢丝因位置角度不同而产生了较大的疲劳特性差异，且相比轴向循环拉伸，该工况下最不利单丝的微动疲劳寿命更低；与非接触区域相比，接触区的疲劳寿命大幅降低，微动现象对钢绞线索的抗疲劳性能有明显降低作用．     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

Experimental investigation of hydrodynamic loads and pressure distribution during a pyramid water entry

In the maritime environment slamming is a phenomenon known as short duration impact of water on a floating or sailing structure. Slamming loads are local and could induce very high local stresses. This paper reports a series of impact test results and investigate the slamming loads and pressures acting on a square based pyramid. In this study the slamming tests have been conducted at constant velocity impact with a hydraulic high speed shock machine. This specific experimental equipment avoids the deceleration of the structure observed usually during water entry with drop tests. Three velocities of the rigid pyramid have been used (10, 13 and 15 m s⁻¹). Time-histories of local pressures, accelerations and slamming loads were successfully measured. The relationship between the pressure magnitude and the impact velocity is obtained and the spatial distribution of pressures on pyramid sides is characterized. The impact velocity was found to have a negligible influence in predicting the maximum pressure coefficient.     

RV减速器主支撑角接触球轴承混合润滑分析

针对RV减速器角接触球轴承承受预紧力、轴向力和径向力等联合外载荷作用的工况,分析得出了内、外圈滚道接触界面的接触区几何参数和接触载荷.在此基础上,综合考虑了角接触球轴承的接触区宏观几何、接触载荷、真实表面粗糙度、瞬态效应等因素,建立了角接触球轴承混合润滑数学模型,分析了在不同工况下角接触轴承的润滑状况及表面以下应力分布.结果表明:随着载荷的不断增加,钢球与内圈沟道之间的油膜厚度会不断减少,导致干接触面积迅速扩大,接触点表面以下最大应力增大;转速的增加会使油膜变厚,干接触面积缩小.该结果对角接触球轴承的实际工程应用具有重要借鉴意义.     

地下工程爆破对危岩稳定性的影响

根据爆破峰值速度衰减规律及危岩体主控结构面的假定，通过欧拉方程确定作用于危岩体峰值爆破荷载，并对峰值荷载进行修正得到时程爆破惯性力，建立了3类危岩体动力物理模型及计算模型，结合极限平衡方法得到3类危岩体动力稳定系数计算方法，选取最小的稳定性系数作为整个危岩体的动力稳定性系数，最终给出了3类危岩动力稳定性评价方法。以重庆市万州区太白危岩体为例，选取5个代表性危岩体进行动力稳定性计算，结果表明，3类危岩体动力稳定系数计算方法能较好地评价和反映危岩体的动力性态。     

冲角工况下列车车轮损伤机理研究

曲线通过和蛇行运动时将会在轮轨间产生一定的冲角,为探究列车车轮在冲角工况下的损伤机理,利用JD-1轮轨模拟试验机对列车车轮进行滚动接触疲劳试验.结果表明:在冲角工况下车轮试件磨痕的不同区域存在不同的损伤机理,按损伤机理的不同可以将其分为塑性堆积区、疲劳损伤区和磨损区三个区域.在应力发生剧烈变化且应力方向由高应力区指向低应力区的区域将会出现材料的塑性堆积,并且在堆积处产生疲劳裂纹.滚动接触下的疲劳裂纹可以萌生于表面和亚表面,在较强应力作用下,车轮材料的晶粒发生了明显的细化,在横截面上呈现出纤维状组织.     

一种轿车车轮应力状态测量与分析方法

基于台架应变测试试验方法,研究轿车车轮在疲劳试验中的应力状态。结果表明:车轮的径向疲劳试验时,轮胎会对车轮的载荷产生较大的影响,轮胎与转鼓的挤压变形以及正反转动都会对车轮的应力状态产生影响;车轮径向疲劳试验时,最大应变出现在轮辋与轮胎接触位置沿车轮圆周方向,而在靠近轮心位置的应变较小;车轮弯曲疲劳试验时,最大应变出现在轮辐靠近轮心的位置,最大应变出现在轮辐的长度方向;不同的载荷对车轮应变的变化规律并没有影响,但是会对最大和最小峰值产生影响。