一种通过梯形PPMgLN波导倍频实现带宽可调谐光源的理论研究

本文设计了一种梯形的周期极化掺镁铌酸锂(PPMgLN)波导,并通过在传播方向上引入温度梯度来拓宽其倍频(SHG)过程的泵浦光源可接收带宽。通过有限差分的光束传输法,计算波导的有效折射率,并进行波导尺寸的设计。结果表明,通过改变梯形波导不同位置的温度,使其形成一个温度梯度,可拓宽泵浦光源的波长可接收带宽。本文所设计的PPMgLN波导最大泵浦光源可接收带宽为C波段,即1 530~1 565 nm,该波导可倍频C波段,得到输出波段带宽为765~782.5 nm,温度调谐范围为30~150 ℃。     

以磷化铁为添加剂沿(111)面生长磷掺杂金刚石大单晶

掺杂是调控金刚石性能的一种重要手段。本文采用温度梯度法,在5.6 GPa、1 312 ℃的条件下,选用Fe₃P作为磷源进行磷掺杂金刚石大单晶的合成。金刚石样品的显微光学照片表明,随着Fe₃P添加比例的增加,金刚石晶体的颜色逐渐变深,包裹体数量逐渐增加,晶形由板状转变为塔状直至骸晶。金刚石晶形的变化表明Fe₃P的添加使生长金刚石的V形区向右偏移,这是Fe₃P改变触媒特性的缘故。红外光谱分析表明,Fe₃P的添加使金刚石晶体中氮含量上升,这说明磷的进入诱使氮原子更容易进入金刚石晶格中。激光拉曼光谱测试表明,随着Fe₃P添加比例的增加,所合成的掺磷金刚石的拉曼峰位变化不大,其半峰全宽(FWHM)值变大,这说明磷的进入使得金刚石晶格畸变增加。XPS测试结果显示,随着Fe₃P添加比例的增加,金刚石晶体中磷相对碳的原子百分含量也会增加,这意味着添加Fe₃P所合成的金刚石晶体中有磷存在。     

Nonlinear elastic constitutive relations of residually stressed composites with stiff curved fibres

Applied Mathematics and Mechanics - Mechanical models of residually stressed fibre-reinforced solids, which do not resist bending, have been developed in the literature. However, in some residually...     

Euler Characteristics on virtually free products

We define Euler characteristics on classes of residually finite and virtually torsion free groups and we show that they satisfy certain formulas in the case of amalgamated free products and HNN extensions over finite subgroups. These formulas are obtained from a general result which applies to the rank gradient and the first L²?Betti number of a finitely generated group.     

Distribution dependent stochastic differential equations

Due to their intrinsic link with nonlinear Fokker-Planck equations and many other applications, distribution dependent stochastic differential equations (DDSDEs) have been intensively investigated. In this paper, we summarize some recent progresses in the study of DDSDEs, which include the correspondence of weak solutions and nonlinear Fokker-Planck equations, the well-posedness, regularity estimates, exponential ergodicity, long time large deviations, and comparison theorems.     

基于视觉辐条图案识别方法的蓝宝石引晶机制研究

工业生产蓝宝石晶体过程中,引晶步骤有着至关重要的地位。引晶必须在温度梯度较小,温度分布趋于稳定的条件下进行。目前,工业生产蓝宝石主要依靠人工经验操控籽晶杆实现引晶操作,但是人工引晶操作的准确性不高会导致成品品质不佳、资源浪费。为此,本文提出一种基于蓝宝石视觉辐条图案识别方法来检测蓝宝石熔体状态自由液面状态,从而实现一种高效率引晶的机制。此方法利用经典骨架化算法细化辐条图案,Harris算子实现特征信息的提取,提取的特征信息放入运动轨迹模型中判断熔体稳定性,分析液面温度分布稳定性从而实现引晶。结果表明,此算法具有有效性,蓝宝石晶体引晶效率大大提高,生产出的成品良率也有提升,可有效指导蓝宝石的工业生产。     

SIMS of organic layers with unknown matrix parameters: Locating the interface in dual beam argon gas cluster depth profiles

Four simple methods are evaluated to determine their accuracies for establishing the interface location in secondary ion mass spectrometry intensity depth profiles of organic layers where matrix effects have not been measured. Accurate location requires the separate measurement of each ion's matrix factor. This is often not possible, and so estimates using matrix-less methods are required. Six pure organic material interfaces are measured using many secondary ions to compare their locations from the four methods with those from full evaluation with matrix terms. For different secondary ions, matrix effects cause the apparent interface positions to vary over 20 nm. The shifts in the intensity profiles on going from a layer of P into a layer of Q are in the opposite direction to that for going from Q into P, so doubling layer thickness errors. The four methods are as follows: M1, use of the median interface position in the intensity profiles for the five lightest ions for 15 ≤ m/z ≤ 150; M2, extrapolation of the position for each ion to m/z = 0 for ions with m/z ≤ 150; M3, as M2 but for m/z ≤ 300; and M4, the extreme positions for all m/z ≤ 100. Comparison with the location using matrix terms shows their ranking, from best to worst, to be M4, M3, M1, and M2 with average errors of 10%, 12%, 14%, and 17%, respectively, of the profile interface full widths at half maximum. Use of pseudo-molecular ions is very much poorer, exceeding 50%, and should be avoided.     

多元统计分析中一类矩阵迹函数最小化问题的有效算法

研究来源于多元统计分析中的一类矩阵迹函数最小化问题$\min c+ tr(AX)+\sum\limits_{j=1}^{m}tr(B_j X C_jX^{T}),\ \ {\rm s. t.} \ X^TX=I_p,$其中$c$为常数, $A\in R^{p\times n}\ (n\geq p)$, $B_j\in R^{n\times n}, C_j\in R^{p\times p}$为给定系数矩阵. 数值实验表明已有的Majorization算法虽可行, 但收敛速度缓慢且精度不高. 本文从黎曼流形的角度重新研究该问题, 基于Stiefel流形的几何性质, 构造一类黎曼非单调共轭梯度迭代求解算法, 并给出算法收敛性分析.数值实验和数值比较验证所提出的算法对于问题模型是高效可行的.     

三维位势问题的梯度边界积分方程的新解法

三维位势问题的边界元分析中,关于坐标变量的边界位势梯度的计算是一个困难的问题. 已有一些方法着手解决这个问题,然而,这些方法需要复杂的理论推导和大量的数值计算. 本文提出求解一般边界位势梯度边界积分方程的辅助边值问题法. 该方法构造了与原边界值问题具有相同解域的辅助边值问题,该辅助边值问题具有已知解,因此通过求解此辅助边值问题,可获得梯度边界积分方程对应的系统矩阵,然后将此系统矩阵应用于求解原边值问题,求解过程非常简单,只需求解一个线性系统即可获得原边值问题的解. 值得注意的是,在求解原边值问题时,不再需要重新计算系统矩阵,因此辅助边值问题法的效率并不很差. 辅助边值问题法避免了强奇异积分的计算,具有数学理论简单、程序设计容易、计算精度高等优点,为坐标变量梯度边界积分方程的求解提供了一个新的途径. 3个标准的数值算例验证了方法的有效性.      

“Grafting through” polymerization involving surface-bound monomers

“Grafting through” polymerization represents copolymerization of free monomers in solution and polymerizable units bound to a substrate. Free polymer chains are formed initially in solution and can incorporate the surface-bound monomers, and thereby, get covalently bonded to the surface during the polymerization process. As more growing chains attach to the surface-bound monomers, an immobilized polymer layer is formed on the surface. We use a combination of computer simulation and experiments to comprehend this process for monomers bound to a flat impenetrable substrate. We concentrate specifically on addressing the effect of spatial density of the surface-bound monomers on the formation of the surface-attached polymers. We employ a lattice-based Monte Carlo model utilizing the bond fluctuation model scheme to provide molecular-level insight into the grafting process. For experimental validation, we create gradients of density of bound methacrylate units on flat silicon wafers using organosilane chemistry and carry out “grafting through” free radical polymerization initiated in bulk. We report that the proximity of the surface-bound polymerizable units promotes the “grafting through” process but prevents more free growing chains to “graft through'' the polymerizable units. The “grafting through” process is self-limiting in nature and does not affect the overall density of the surface-bound polymer layer, except in case of the highest theoretical packing density of surface-bound monomers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016, 54, 263–274