发动机机油滤清器虑层强度分析及优化

针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa.     

移动加热器法生长碲锌镉晶体的组分输运与界面形貌研究

移动加热器法(THM)生长碲锌镉晶体时,界面稳定性对晶体生长的质量有很大影响。本文基于多物理场有限元仿真软件Comsol建立了THM生长碲锌镉晶体的数值模拟模型,讨论了Te边界层与组分过冷区之间的关系,对不同生长阶段的物理场、Te边界层与组分过冷区进行仿真研究,最后讨论了微重力对物理场分布的影响,并对比了微重力与正常重力下的生长界面形貌。模拟结果表明,Te边界层与组分过冷区的分布趋势是一致的,在不同生长阶段,流场中次生涡旋的位置会发生移动,从而导致生长界面的形貌随着生长的进行发生变化,同时微重力条件下形成的生长界面形貌最有利于单晶生长。因此,在晶体生长的中前期,对次生涡旋位置的控制和对组分过冷的削弱,是THM生长高质量晶体的有效方案。     

阳离子交换皂石黏土在基质辅助激光解吸电离飞行时间质谱分析中的应用

将一种人工合成的无机聚合物——蒙脱石皂石黏土（smectite，Sm）应用于基质辅助激光解吸电离飞行时间质谱分析（matrix-assisted laser desorption/ionization time of flight mass spectrometry, MALDI-TOF-MS），以检测糖类化合物。 将传统的有机基质2，4，6-三羟基苯乙酮（trihydroxyacetophenone, THAP）与阳离子交换后的皂石黏土混合制备成新型复合基质，应用于糖类化合物的检测。通过比较不同的制样方法，测定不同分子直径的糖类化合物，发现由于受复合基质晶面间距的限制，只有小分子糖类化合物能进入晶面间隙充分接触有机基质并被离子化，从而实现对小分子糖类化合物的选择性检测。     

A Stable Porphyrin Functionalized Graphite Electrode Used at the Oxygen Evolution Reaction Potential

Many researches have been devoted to rechargeable power generators that can store (but also release) energy. This availability is ensured through (e. g.) the oxygen evolution reaction (OER). However, (i) large values of the overpotentials and (ii) a progressive detriment of the anode (graphite) electrode limit the ultimate device. In view of enhancing the electrode performances, graphite was protected by following different strategies, which oblige to follow precise preparation protocols. Here, we prove that a thin layer of free-base porphyrin molecules is able to protect the underneath graphite electrode from detriment even if many (about 100) electrochemical cycles are performed.     

Metamorphic InAs(Sb)/InGaAs/InAlAs nanoheterostructures grown on GaAs for efficient mid-IR emitters

High-efficiency semiconductor lasers and light-emitting diodes operating in the 3–5?μm mid-infrared (mid-IR) spectral range are currently of great demand for a wide variety of applications, in particular, gas sensing, noninvasive medical tests, IR spectroscopy etc. III-V compounds with a lattice constant of about 6.1?Å are traditionally used for this spectral range. The attractive idea to fabricate such emitters on GaAs substrates by using In(Ga,Al)As compounds is restricted by either the minimum operating wavelength of ～8?μm in case of pseudomorphic AlGaAs-based quantum cascade lasers or requires utilization of thick metamorphic In_xAl_1-xAs buffer layers (MBLs) playing a key role in reducing the density of threading dislocations (TDs) in an active region, which otherwise result in a strong decay of the quantum efficiency of such mid-IR emitters. In this review we present the results of careful investigations of employing the convex-graded In_xAl_1-xAs MBLs for fabrication by molecular beam epitaxy on GaAs (001) substrates of In(Ga,Al)As heterostructures with a combined type-II/type-I InSb/InAs/InGaAs quantum well (QW) for efficient mid-IR emitters (3–3.6?μm). The issues of strain relaxation, elastic stress balance, efficiency of radiative and non-radiative recombination at T?=?10–300?K are discussed in relation to molecular beam epitaxy (MBE) growth conditions and designs of the structures. A wide complex of techniques including in-situ reflection high-energy electron diffraction, atomic force microscopy (AFM), scanning and transmission electron microscopies, X-ray diffractometry, reciprocal space mapping, selective area electron diffraction, as well as photoluminescence (PL) and Fourier-transformed infrared spectroscopy was used to study in detail structural and optical properties of the metamorphic QW structures. Optimization of the growth conditions (the substrate temperature, the As₄/III ratio) and elastic strain profiles governed by variation of an inverse step in the In content profile between the MBL and the InAlAs virtual substrate results in decrease in the TD density (down to 3?×?10⁷ cm^?2), increase of the thickness of the low-TD-density near-surface MBL region to 250–300?nm, the extremely low surface roughness with the RMS value of 1.6–2.4?nm, measured by AFM, as well as rather high 3.5?μm-PL intensity at temperatures up to 300?K in such structures. The obtained results indicate that the metamorphic InSb/In(Ga,Al)As QW heterostructures of proper design, grown under the optimum MBE conditions, are very promising for fabricating the efficient mid-IR emitters on a GaAs platform.     

XPS study of silicon spheres as a density standard

As density is one of the basic physical properties of materials, an accurate density standard is absolutely essential. To determine density with high accuracy and precision, two 1-kg single-crystal silicon spheres (NMIJ-S4 and NMIJ-S5) are used as the primary standard at the National Metrology Institute of Japan. For the accurate measurement of the mass and volume of the silicon spheres, the effects of the surface layer must be carefully considered. In this work, a surface layer model of NMIJ-S4 and NMIJ-S5 was proposed and the thicknesses of each surface layer were determined using X-ray photoelectron spectroscopy. A detailed uncertainty budget is presented to aid use of the density standard.     

A simple method for extracting both active oily and water soluble extract (WSE) from Nigella sativa (L.) seeds using a single solvent system

The current study provides a way of extraction for both active NSO and WSE from Nigella sativa seeds using 98% methanol. About 1?kg of ground seeds was macerated by 1:2.5 w/v (g/mL) for 72?hours. After rotary evaporation and 7 days of continuous drying and chilling at 50 and 4?°C, NSO and WSE were obtained at the same instant. Solubility tests of 24 solvents and 11 thin layer chromatographic analyses while 2, 2-diphenyl-1-picrylhydrazyl free radical scavenging assay of NSO (73.66) , WSE (33.32) and NSO?+?WSE (78.22) against ascorbic acid (IC50?=?4.28?mg/mL) was performed. WSE was found to be highly soluble in water and 5% NaOH exhibiting the same Rf value of 0.95 for EtOH:DMSO (9:1) against the honey. WSE has revealed more than twofold higher anti-oxidant activity than others. Formulation of WSE with Tualang honey may provide better targeted hydrophilic drug delivery systems.     

A general stability result for the semilinear viscoelastic wave model under localized effects

Our main goal in the present work is to address an integro-differential model under localized viscoelastic and frictional effects arising in the Boltzmann theory of viscoelasticity. More precisely, we consider a general version in the history context of the pioneer localized viscoelastic problem approached by Cavalcanti and Oquendo (2003) in the null history scenario, and more recently by Cavalcanti et al. (2018) in the history framework. By means of a new observability inequality, we prove a general stability result to the model under a weaker assumption on the localized frictional damping and a slower condition on the decreasing memory kernel (of polynomial type) than the previously mentioned works. To achieve such stability results, we still work in a general setting by removing the assumption on complementary damping mechanisms and show, in some reasonable situations concerning the density coefficient, that the localized viscoelastic effect is enough to ensure the general stability (of polynomial type) to the problem.     

Scattering of Tollmien-Schlichting waves by localized roughness in transonic boundary layers

The laminar-turbulent transition in boundary-layer flows is often affected by wall imperfections, because the latter may interact with either the freestream perturbations or the oncoming boundary-layer instability modes, leading to a modification of the accumulation of the normal modes. The present paper particularly focuses on the latter mechanism in a transonic boundary layer, namely, the effect of a two-dimensional(2 D) roughness element on the oncoming Tollmien-Schlichting(T-S) modes when they propagate through the region of the rapid mean-flow distortion induced by the roughness. The wave scattering is analyzed by adapting the local scattering theory developed for subsonic boundary layers(WU, X. S. and DONG, M. A local scattering theory for the effects of isolated roughness on boundary-layer instability and transition: transmission coefficient as an eigenvalue. Journal of Fluid Mechanics, 794, 68–108(2006)) to the transonic regime, and a transmission coefficient is introduced to characterize the effect of the roughness. In the sub-transonic regime, in which the Mach number is close to, but less than, 1, the scattering system reduces to an eigenvalue problem with the transmission coefficient being the eigenvalue; while in the super-transonic regime, in which the Mach number is slightly greater than 1, the scattering system becomes a high-dimensional group of linear equations with the transmission coefficient being solved afterward. In the largeReynolds-number asymptotic theory, the K′arm′an-Guderley parameter is introduced to quantify the effect of the Mach number. A systematical parametric study is carried out,and the dependence of the transmission coefficient on the roughness shape, the frequency of the oncoming mode, and the K′arm′an-Guderley parameter is provided.     

超声速流动中非线性EASM湍流模式应用研究

针对超声速复杂流动区域精确模拟的需要，发展了基于k-ω可压缩修正形式的非线性显式代数雷诺应力模式（EASM），提高了该模式对超声速复杂流动的数值模拟精度。通过对二维超声速凹槽和三维双椭球的数值计算表明，与SA和SST常规线性涡黏性湍流模式比较，非线性的EASM模式对大分离以及剪切层流动结构的刻画能力更精细，对剪切层再附区的压力及摩擦系数分布模拟更加精确；EASM模式能够准确地模拟二次激波引起的压强和热流分布情况。