基于Rietveld精修方法解析Bi2O3的原子热振动

三氧化二铋(Bi₂O₃)是氧离子导电体,为了获得它的原子热振动各向同性温度因子,对该粉末晶体进行X射线衍射实验,建立了晶体结构模型,利用Rietveld 精修方法的RIETAN-2000 程序对所得实验结果进行了晶体结构精修,通过最大熵方法(MEM)解析得到了粉末晶体的等高电子密度分布三维(3D) 和二维(2D)可视化图谱。结果表明,各原子Bi₍₁₎、Bi₍₂₎、O₍₁₎、O₍₂₎和O₍₃₎的原子热振动各向同性温度因子分别为0.004 938 nm²、0.004 174 nm²、0.007 344 nm²、0.007 462 nm²、和0.007 857 nm²,等高电子密度分布的可视化,进一步验证了晶体结构模型和原子位置的准确性,这些参数对研究晶体材料的热性质具有一定参考意义。     

单面柱局域共振声子晶体低频带隙特性分析及结构改进研究

基于有限元法对单面柱局域共振声子晶体进行带隙特性分析,研究了结构参数对该类型声子晶体的影响。结果表明:随着散射体高度的增加,单面柱声子晶体的第一完全带隙的起始频率逐渐降低,带宽逐渐增大;随着基板厚度的增大,单面柱声子晶体的起始频率逐渐升高,截止频率先增大后减小。并且在经典单面柱声子晶体的基础上,组合了两种新型的三组元单面柱声子晶体结构:嵌入式单面柱声子晶体(以下简称结构Ⅰ)和粘接式单面柱声子晶体(以下简称结构Ⅱ)。通过对其带隙特性的分析得出:这两种新结构与经典的单面柱声子晶体相比,都具有更低频的带隙,这对于低频减振降噪是非常有利的。本文的结果将对实际的工程应用提供一定的理论指导。     

一种通过梯形PPMgLN波导倍频实现带宽可调谐光源的理论研究

本文设计了一种梯形的周期极化掺镁铌酸锂(PPMgLN)波导,并通过在传播方向上引入温度梯度来拓宽其倍频(SHG)过程的泵浦光源可接收带宽。通过有限差分的光束传输法,计算波导的有效折射率,并进行波导尺寸的设计。结果表明,通过改变梯形波导不同位置的温度,使其形成一个温度梯度,可拓宽泵浦光源的波长可接收带宽。本文所设计的PPMgLN波导最大泵浦光源可接收带宽为C波段,即1 530~1 565 nm,该波导可倍频C波段,得到输出波段带宽为765~782.5 nm,温度调谐范围为30~150 ℃。     

Effect of thickness variations of lithium niobate on insulator waveguide on the frequency spectrum of spontaneous parametric down-conversion

We study the effect of waveguide thickness variations on the frequency spectrum of spontaneous parametric down-conversion in the periodically-poled lithium niobate on insulator (LNOI) waveguide. We analyze several variation models and our simulation results show that thickness variations in several nanometers can induce distinct effects on the central peak of the spectrum, such as narrowing, broadening, and splitting. We also prove that the effects of positive and negative variations can be canceled and thus lead to a variation-robust feature and an ultra-broad bandwidth. Our study may promote the development of on-chip photon sources in the LNOI platform, as well as opens up a way to engineer photon frequency state.     

Highly stable dielectric frequency response of chemically synthesized Mn-substituted ZnFe2O4

The tenacity of the present study was to develop a material using an economical chemical route, having balance between magnetic and dielectric order parameters for maximum transmittance of electromagnetic waves in order to use them in shielding materials. In this context, Mn-Zn ferrites were prepared using a wet chemical based sol-gel auto-combustion technique. X-ray diffraction confirmed the pure phase formation of samples, while some impurity peaks were also present for the higher value of Mn substitution. Field emission scanning electron microscopy revealed a decrease in grain size with increasing Mn substitution. While energy dispersive X-ray spectroscopy confirmed the elemental composition of pure and Mn substituted samples, the dielectric constant, dielectric loss and tangent loss were decreased with increasing frequency and increasing Mn substitution. The complex electric modulus was found to be a function of frequency and values of complex electric modulus were increased with increasing frequency and Mn substitution. The complex impedance of RC series circuit and RC parallel circuit was also decreased with increasing both the parameters while AC conductivity was increased in the series. Dielectric frequency response was also studied for the prepared samples and the best match was found with expected results. The Nyquist and Cole-Cole plots revealed the semi-conductive behavior at higher frequency and Mn substitution also yielded the same results. The relative stability of the samples to be used as dielectric materials was also studied using Bode and Nichols plots, and a comparatively high gain margin was observed, well suitable for potential applications in electromagnetic shielding.     

不同浓度的尾砂胶结充填体破坏过程 声发射特性试验研究*

制备了3种不同质量浓度的充填体试件，进行了单轴压缩声发射试验，分析了不同浓度的充填体力学特性，重点研究了试件破坏过程中的声发射振铃计数、声发射累计撞击数与声发射累计能量的比值(r值)、主频及其相对高频信号激增响应系数特征。研究表明：随着浓度的增加，充填体的峰值强度与弹性模量呈增大趋势，充填体中出现的声发射累计振铃计数越多；r值先升高再持续减小到一个较低值，随着外载荷的增加，进入缓慢升高阶段，峰值前均保持在该阶段。充填体破裂前兆信息在声发射信号主频分布中呈现主频段增多现象，表现为由加载初期的1~2个主频段，在临界主破裂时增多到3~5个主频段；且随着浓度的增加，声发射信号主频频段分布越宽，声发射相对高频信号(160~180 kHz)的激增响应系数呈递减趋势。以上特征可为不同浓度的尾砂胶结充填体稳定性监测、预测提供依据。     

Dynamic and buckling analysis of polymer hybrid composite beam with variable thickness

This work deals with a study of the dynamic and buckling analysis of polymer hybrid composite(PHC) beam. The beam has variable thickness and is reinforced by carbon nanotubes(CNTs) and nanoclay(NC) simultaneously. The governing equations are derived based on the first shear deformation theory(FSDT). A three-phase HalpinTsai approach is used to predict the mechanical properties of the PHC. We focus our attention on the effect of the simultaneous addition of NC and CNT on the vibration and buckling analysis of the PHC beam with variable thickness. Also a comparison study is done on the sensation of three impressive parameters including CNT, NC weight fractions, and the shape factor of fillers on the mechanical properties of PHC beams,as well as fundamental frequencies of free vibrations and critical buckling load. The results show that the increase of shape factor value, NC, and CNT weight fractions leads to considerable reinforcement in mechanical properties as well as increase of the dimensionless fundamental frequency and buckling load. The variation of CNT weight fraction on elastic modulus is more sensitive rather than shear modulus but the effect of NC weight fraction on elastic and shear moduli is fairly the same. The shape factor values more than the medium level do not affect the mechanical properties.