FeCoCrCuNi高熵合金裂纹及孔洞结构力学与微观构象演化机理的分子动力学模拟研究

本文采用分子动力学方法研究了FeCoCrCuNi高熵合金裂纹及孔洞模型结构在不同轴向拉伸应变速率下的力学与微观结构演化机理. 结果表明：应变速率越高FeCoCrCuNi裂纹结构对应更高的过冲应变和过冲应力，其主要原因是高拉伸速率会导致高强度的BCC结构及孪晶结构的生成，而BCC结构及孪晶结构的产生进而会抑制应力的下降，通过应力-应变曲线，可知FeCoCrCuNi裂纹模型在轴向应力作用下表现为塑性形变. 对于不同尺寸的孔洞FeCoCrCuNi裂纹模型的应力模拟与结构分析，可以得出：孔洞尺寸越大, FeCoCrCuNi裂纹结构对应的过冲应变和过冲应力越小，其主要原因是大尺寸的孔洞造成孔洞之间产生裂纹的，进而会影响这个材料的屈服应变和屈服强度.     

ICP-AES法测定高温合金中5种非金属元素

本文研究了快速测定高温合金中5种非金属元素(As、B、P、Se、Si)的分析方法,以满足高温合金行业对非金属元素检测的需求。利用王水和高氯酸对高温合金进行酸溶解,并系统研究了基体元素和共存元素对分析元素谱线的光谱干扰情况,同时进行了分析谱线的选择。5种非金属元素的检出限在5.5 ～ 11.9 ug/ml,5次数据的相对标准偏差(RSD,n=5)为0.9 % ～ 7 %,各元素的回收率在96 % ～ 102 %之间,该方法适用于高温合金中非金属元素的测定。     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

Ultrafine PtRu Dilute Alloy Nanodendrites for Enhanced Electrocatalytic Methanol Oxidation

Dilute alloy nanostructures have been demonstrated to possess distinct catalytic properties. Noble-metal-induced reduction is one effective synthesis strategy to construct dilute alloys and modify the catalytic performance of the host metal. Herein, we report the synthesis of ultrafine PtRu dilute alloy nanodendrites (PtRu NDs, molar ratio Ru/Pt is 1:199) by the reduction of Ru^III ions induced by Pt metal. For the methanol oxidation reaction, PtRu NDs showed the highest forward peak current density (2.66 mA cm⁻², 1.14 A/mg_Pt) and the best stability compared to those of pure-Pt nanodendrites (pure-Pt NDs), commercial PtRu/C and commercial Pt/C catalysts.     

FeNi Alloy Nanoparticles Encapsulated in Carbon Shells Supported on N-Doped Graphene-Like Carbon as Efficient and Stable Bifunctional Oxygen Electrocatalysts

The development of cost-effective and durable oxygen electrocatalysts remains highly critical but challenging for energy conversion and storage devices. Herein, a novel FeNi alloy nanoparticle core encapsulated in carbon shells supported on a N-enriched graphene-like carbon matrix (denoted as FeNi@C/NG) was constructed by facile pyrolyzing the mixture of metal salts, glucose, and dicyandiamide. The in situ pyrolysis of dicyandiamide in the presence of glucose plays a significant effect on the fabrication of the porous FeNi@C/NG with a high content of doped N and large specific surface area. The optimized FeNi@C/NG catalyst displays not only a superior catalytic performance for the oxygen reduction reaction (ORR, with an onset potential of 1.0 V and half-wave potential of 0.84 V) and oxygen evolution reaction (OER, the potential at 10 mA cm⁻² is 1.66 V) simultaneously in alkaline, but also outstanding long-term cycling durability. The excellent bifunctional ORR/OER electrocatalytic performance is ascribed to the synergism of the carbon shell and FeNi alloy core together with the high-content of nitrogen doped on the large specific surface area graphene-like carbon.     

Electrolytic PdMo deposits with high corrosion resistance in relation to palladium

1. Download : Download high-res image (72KB)
2. Download : Download full-size image

     

Highly selective hydrogenation of acetophenone over supported amorphous alloy catalyst

Alpha-phenylethanol (PE) is an essential chemical in the field of medicine and synthetic perfumery. Therefore, in this work, we used a supported Ni–B–P amorphous alloy catalyst (Ni–B–P/SiO₂) in the hydrogenation of acetophenone (AP) to α-PE, which demonstrated excellent catalytic activity and selectivity, compared with Ni–B/SiO₂ (KBH₄ reduction of nickel salt). Ni–B–P/SiO₂ exhibited a high AP hydrogenation conversion of approximately 99%, whereas the PE selectivity reached up to 94%, which is approximately 1.4-fold higher than that of Ni–B/SiO₂ (about 69%), thereby directly proving the unique inhibition of AP hydrogenation over hydrogenation of P in the Ni–B catalytic system. The doped P in Ni–B–P/SiO₂ enhances the oxidation resistance and maintains the valence stability of Ni and B. Furthermore, sufficient experimental data were collected to determine the kinetic parameters. Based on the Langmuir–Hinshelwood model, we assumed that (i) AP and H₂ compete for adsorption on Ni–B–P/SiO₂; (ii) AP has strong adsorptive capacity on Ni–B–P/SiO₂; and (iii) PE coverage on the catalyst was negligible. Then, the dynamic equation was derived, which indicated that experimental data agree well with the dynamic model. Finally, the activation energy was confirmed to be 50.73 KJ/mol. This report will open up an avenue for the industrialization of amorphous alloy catalysts.     

形状记忆合金椭圆孔口问题的有限单元法

基于Lagoudas形状记忆合金(SMA)三维本构模型,假设材料为各向同性,推导了SMA平面应力状态的增量型本构方程,继而编写了ABAQUS用户自定义材料(UMAT)子程序,研究了在双向拉伸情况下,外载荷、温度、椭圆孔口长短轴之比对超弹性SMA椭圆孔口板中应力诱发马氏体相变区的影响。数值结果表明:应力诱发马氏体相变首先发生在椭圆孔口长轴端点部位,在外加载荷作用下逐渐扩展到板内,并由内向外形成马氏体相区、相变混合区和奥氏体相区;SMA板内应力诱发马氏体完全相变区面积与施加外载荷成正相关,与温度成负相关;随着椭圆孔口长短轴之比增大,SMA板内应力诱发马氏体完全相变区面积呈现出先减小后增大的趋势;拉应力差值相同时,相较于拉应力沿椭圆孔口长轴方向较大的情况,当拉应力沿椭圆孔口短轴方向较大时,SMA板内完全相变区面积较大,椭圆孔口周边应力集中现象更明显。     

Preparation and performance of (Co,Mn)3O4 spinel coating on Crofer alloy by composite electrodeposition and step-heating thermal conversion

The preparation and performance improvement of the spinel coating on the surface of ferritic alloy is of wide interest for its application in the metallic interconnects of the solid oxide fuel cells (SOFCs). The Co Mn₂O₃ composite coating is prepared on the surface of the Crofer alloy by the composite electrodeposition method. A step-heating thermal conversion process is subsequently used to convert the composite coating into a spinel coating, while a direct-heating process is implemented as the control experiment. Isothermal oxidation tests are then carried out for the prepared samples in order to present the high temperature performance. Scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and area-specific resistance (ASR) are used to analyze the properties of the matrix and coatings. The experimental results reveal that the coatings by step-heating thermal conversion exhibit better performance of electrical conductivity and oxidation resistance than the coatings by direct-heating process. Furthermore, with the increase of oxidation time, the atomic proportion of Cr element diffusing to the surface of the matrix is maintained at about 3%–4% for the samples with spinel coatings by step heating, which effectively prevent the Cr volatilization in the matrix. The preparation of spinel coatings on the ferritic alloy by composite electrodeposition and step-heating thermal conversion is helpful to stimulate new ideas for the development of reliable and cost-effective metallic interconnect.     

Effect of transition elements on dispersoid formation and elevated-temperature mechanical properties in 6082 aluminum alloy

ABSTRACT

The effect of transition elements, specifically Mn, Cr, V, and Mo, on dispersoid formation and mechanical properties in 6082 aluminum alloy was studied. The elevated-temperature mechanical properties were evaluated based on the compressive yield strength and creep resistance. The results indicated that the addition of Mn to the 6082 alloy resulted in the formation of a large number of the thermally stable α-Al(MnFe)Si dispersoids, thereby significantly improving the elevated-temperature mechanical properties of the alloy. Subsequent additions of Cr, V, and Mo increased the amount of Mn-bearing intermetallic phases, which decreased the supersaturation levels of Mn and Si in the α-Al, and consequently decreased the volume fraction of the dispersoids. The alloys containing Cr, V, and Mo exhibited similar yield strengths at 300°C and higher yield strengths at room temperature compared to the alloy containing only Mn. The size effect of the smaller dispersoids containing Cr, V, and Mo together with the solid-solution hardening of these elements could balance out the strength decrease resulting from the decreased volume fraction of the dispersoids. The additions of Cr, V, and Mo significantly increased the creep resistance of the Mn-containing 6082 alloy. Vanadium induced the highest creep resistance followed by Cr and Mo. Solute atoms of these elements with low diffusivity in the aluminum matrix contributed significantly to increasing the creep resistance at 300°C.