排序方式: 共有41条查询结果,搜索用时 15 毫秒
1.
为探究水牛角的结构性能关系,基于上海同步辐射光源搭建了高分辨原位CT系统,对水牛角角鞘进行初始表征和准静态压缩下的实时表征,并通过Top-Hat方法提取了角鞘内孔洞三维形貌。结果显示,水牛角角鞘孔隙率在1%左右,椭圆柱状孔洞沿牛角生长方向排列成线,首尾相连却并未连通,均匀分布在波浪状片层之间。孔洞特征椭球的轴长分布满足对数正态分布,长轴和短轴的长度均值分别为7μm和3μm。原位CT结果表明,角鞘在屈服之后,初始孔洞首先扩张而形成微裂纹,随后微裂纹沿着片层界面由外向内发生桥接,片层发生局部屈曲和层间开裂,形成宏观裂纹,导致角鞘内裂纹密度急剧上升。片层之间不仅存在大量纤维黏接(提高了层间拉伸/剪切强度),而且孔洞互不连通,这些因素抑制了层间裂纹的快速传播,使得各处裂纹只能独立缓慢发展而无法贯通样品。波浪状片层使裂纹传播路径更加曲折,层间屈曲增加了片层摩擦耗能。这些机制使得牛角表现出加工硬化,也是牛角在纵向方向呈现优良韧性的主要原因。 相似文献
2.
We report a design for one nanometer X-ray focusing by a complex refractive lens, which is capable of focusing 20 keV X-rays down to a lateral size of 0.92 nm (full-width at half-maximum (FWHM)) and an axial size of 98 nm (FWHM) with intensity gain of 49050. This complex refractive lens is comprised of a series of kinoform lenses, whose aperture is gradually matched to the converging trace of the X-ray beam so as to increase the numerical aperture (NA). The theoretical principle of the proposed complex refractive lens is presented. The NAs of these lenses are calculated. The numerical simulation results demonstrate that the proposed design can focus the X-ray beam into sub-nanometer while remaining high gain. 相似文献
3.
4.
5.
6.
在所有的相衬成像方法中,X射线同轴轮廓成像由于光路简单、不需要任何光学元件而备受关注.其缺点是无法直接消除散射的影响,从而限制了它在生物医学等领域中的应用.利用数字模拟方法研究了引入散射前后轮廓像的质量随样品到探测器距离的变化情况.模拟结果表明直接轮廓成像存在一个最佳成像距离,因而无法通过改变样品到探测器距离来减小散射的影响.利用定量相衬成像不受成像距离限制的特点,研究了远距离成像时散射的影响.结果表明,样品到探测器的距离增大到一个临界值时,散射对重构像的影响可降到一个极值,此时成像质量得到了明显改善.
关键词:
散射
X射线同轴轮廓成像
定量相衬成像 相似文献
7.
上海光源X射线成像光束线采用多极扭摆器(wiggler)作为辐射光源, 提出一种劳厄双弯晶单色器的设计方案. 计算结果显示, 可获得固定出口的平行单色光束, 能量调谐范围覆盖19—120keV, 在33keV时, 输出光子通量及通量密度分别为1.9×1013phs/s和3.8×1010phs/s/mm2. 分析了劳厄晶体的聚焦及单色化性能, 计算了输出光子通量及单色器的热负载情况. 与传统的双平晶方案相比, 本设计在获得高通量和解决热负载等方面有明显的优越性, 并能有效控制热形变. 相似文献
9.
10.
X-ray tomography of samples containing both weakly and strongly absorbing materials are necessary in material and biomedical imaging. Extending the validity of the phase-attenuation duality (PAD) method, the propagation-based phase-contrast computed tomography (PPCT) of a sample with hybrid compositions of both the light and dense components with 60 keV of synchrotron radiation is investigated. The experimental results show that the PAD-based PPCT is effective in imaging both the weakly and strongly absorbing components simultaneously. Compared with the direct PPCT technique, the PAD-based PPCT technique demonstrates its excellent capability in material discrimination and characterization. In addition, the PAD-based PPCT exhibits a striking performance on the image contrast enhancement and noise suppression. Therefore, this technique is useful for material and biomedical imaging applications, especially when the radiation dose involved imposes a serious constraint. 相似文献