预制层溅射气压对CIGS薄膜结构及器件的影响

研究了金属预制层制备过程中溅射气压对Cu(In_1-xGa_x)Se₂(CIGS)薄膜及电池器件性能的影响.通过调节溅射气压改变预制层的结晶状态及疏松度与粗糙度,在合适的预制层结构下,活性硒化热处理过程中,可使Ga有效地掺入到薄膜中形成优质的CIGS固溶体.高溅射气压会使预制层过于致密,呈现非晶态趋势.经活性硒化热处理后,CIGS薄膜容易产生CIS与CGS"两相分离"现象,从而导致CIGS薄膜太阳电池的开路电压和填充因子降低,电池转换效率由10.03%降低到5.02%.     

热裂解活化硒对CIGS太阳电池开路电压的影响

考察了通过自主研发的高温热裂解辅助硒化装置所产生的高活性硒对CIGS薄膜结构和器件性能的影响.通过调节高温裂解系统的温度可以有效调节不同的硒活性.研究发现, 第一台阶HC-Se气氛可以提高CIGS薄膜表面的Ga含量, 使得CIGS薄膜内的Ga分布更加平缓, 进而提高CIGS薄膜表面禁带宽度.而且HC-Se气氛可以消除CIGS"两相分离"现象.两种因素的共同作用使得CIGS薄膜太阳电池的开路电压提高了34.6%.电池转换效率从6.02%提升至8.76%, 增长了45.5%.     

基于物理中面FGM板屈曲的有限元分析

基于物理中面的概念，根据最小势能原理推导了功能梯度材料FGM薄板屈曲的有限元控制方程，求得临界荷载的有限元解。利用FGM板的屈曲方程与参考均匀板的屈曲方程之间的相似性，建立了FGM板的临界荷载与参考均匀板的临界荷载之间的相似转换关系式，从而将FGM板临界荷载的计算转变为参考均匀板的临界荷载和材料不均匀系数的计算，极大地提高了计算效率，为FGM的推广起积极的推动作用。通过数值算例，将由有限元法和转换关系式得到的临界荷载进行了比较，并讨论了边界条件、荷载工况、材料组成和几何尺寸等对FGM板临界荷载的影响。     

氦原子高激发态的塞曼效应

利用塞曼哈密顿的球张量形式以及塞曼哈密顿在耦合表象中的矩阵元公式,在考虑磁场二次项作用的基础上,研究了氦原子n3P(n=4,5)高激发态的塞曼效应,给出解析解,并绘出了塞曼能级分裂图.     

稀土改质催化剂对废食用油制备燃料油的影响

利用浸渍法制备稀土改质催化剂,用于废食用油脂催化裂解的裂解气催化改质。考察了催化剂活性组分含量、硅铝比、焙烧温度、改质反应温度对产物组成、烯烃含量及收率的影响。得最佳条件:ZSM-5作为催化剂载体,催化剂活性组分镧稀土含量为6%,催化剂焙烧温度为550℃,改质反应温度为360℃。在最佳条件下催化改质,燃料油烯烃含量降低了34.3%,汽油含量提高了14.36%,轻柴油含量提高了1.67%,重柴油含量下降了6.72%,重油含量下降了2.2%,燃料油总收率提高了7.12%,油品质显著提高。     

Raman scattering of polycrystalline GaSb thin films grownby co-evapouration process

<正>This paper reports that GaSb thin films have been co-deposited on soda-lime glass substrates.The GaSb thin film structural properties are characterized by Raman spectroscopy.The Sb-A_1g/GaSb-TO ratio decreases rapidly with the increase of substrate temperature,which suggests a small amount of crystalline Sb in the GaSb thin film and suggests that Sb atoms in the thin film decrease.In Raman spectra,the transverse optical（TO） mode intensity is stronger than that of the longitudinal optical（LO） mode,which indicates that all the samples are disordered.The LO/TO intensity ratio increases with increasing substrate temperature which suggests the improved polycrystalline quality of the GaSb thin film.A downshift of the TO and LO frequencies of the polycrystalline GaSb thin film to single crystalline bulk GaSb Raman spectra is also observed.The uniaxial stress in GaSb thin film is calculated and the value is around 1.0 GPa.The uniaxial stress decreases with increasing substrate temperature.These results suggest that a higher substrate temperature is beneficial in relaxing the stress in GaSb thin film.     

Mo Back Contact for Flexible Polyimide Substrate Cu（In,Ga）Se2 Thin-Film Solar Cells

A dc magnetic sputtering process is applied to growth of a Mo back. contact layer onto the flexible polyimide （PI） and rigid soda-lime glass （SLC） substrates. The structural and electrical properties of the Mo layer coated on the two kinds of substrates are investigated by x-ray diffraction （XRD） and Hall effect measurements. The results show that the Mo layer on SLG indicate more better crystal quality and lower resistivity than that on the PI sheets. In contrast to the SLG substrate, the resistivity of the Mo layer on PI is increased by the vacuum annealing process at the substrate temperature of 450℃ under Se atmosphere, which is attributed to the cracked Mo layer induced by the mismatch of the coefficient of thermal expansion between PI and Mo material. The Cu（In,Ga）Se2 （CIGS） solar cells based on the PI and SLO substrates show the best conversion efficiencies of 8.16% and 10.98% （active area, 0.2cm^2）, respectively. The cell efficiency of flexible CIGS solar cells on PI is limited by its relatively lower fill factor caused by the Mo back contact.     

多晶Cu(In,Ga)Se_2薄膜太阳电池光强特性的研究

本文系统研究了Cu(In,Ga)Se2(CIGS)薄膜太阳电池在入射光强为10～100 mW/cm2范围内的性能参数.结果表明,随光强的减弱,CIGS电池的转换效率、填充因子、短路电流密度和开路电压等性能参数逐步衰减;电池参数与光强的依赖关系可明显划分为两个阶段:光强高于75 mW/cm2时,电池性能变化不大;当光强低于70 mW/cm2时,电池性能衰减明显.这是由于随着光强的降低,RS(串联电阻)值和RSH(并联电阻)值都在升高.其中,RSH值的增大使得CIGS电池的弱光特性变好,但较小的RSH值并不能弥补RS所导致电池性能的衰退.最后,发现高Ga含量的CIGS薄膜电池(8.7%)比低Ga含量(6.9%)的电池弱光特性好.     

Cu(In,Ga)Se_2薄膜太阳电池二极管特性的研究

本文采用线性拟合光态和暗态J-V(电流-电压)曲线的方法计算了不同效率的Cu(In,Ga)Se2(CIGS)薄膜太阳电池的二极管性能参数.在一定范围内,CIGS薄膜电池的二极管品质因子A和反向饱和电流J0值越小,电池的转换效率越高,这说明CIGS电池的复合主要发生在PN结区内.量子效率分析表明,不同效率的CIGS电池在短波区(λ<520 nm)的光谱响应相差不大,而在长波区(520～1100 nm),低效率电池存在很大的吸收,这是由低质量的CIGS吸收层造成的.这进一步验证了光-暗态J-V曲线的分析结果,即高质量的吸收层是制备CIGS电池的关键.     

Preparation of Cu（In,Ga）Se2 Thin Film Solar Cells by Selenization of Metallic Precursors in an Ar Atmosphere

Cu（In, Ga）Se2 thin films are deposited on Mo-coated glass substrates by Se vapour selenization of sputtered metallic precursors in the atmosphere of Ar gas flow under a pressure of about 10 Pa. The in situ heat treatment of as-grown precursor leads to the formation of a better alloy. During selenization, the growth of CuInSe2 phase preferably proceeds through Se-poor phases as CuSe and InSe at relatively low substrate temperature of 250℃, due to the absence of In2Se3 at intermediate stage at low reactor pressure. Subsequently, the Cu（In,Ga）Se2 phase is produced by the reactive diffusion of CuInSe2 with a Se-poor GaSe phase at high temperature of up to 560℃. The final film exhibits smooth surface and large grain size. The absorber is used to fabricate a glass/Mo/Cu（In, Ga）Se2/CdS/ZnO cell with the total-area efficiency of about 7%. The low open-circuit voltage value of the cell fabricated should result from the nonuniform distribution of In and Ga in the absorber, due to the diffusion-controlled reaction during the phase formation. The films, as well as devices, are characterized.