高取代度羧甲基瓜尔胶溶液的微观结构及流变性能

利用环境扫描电子显微镜(ESEM)对粘度在5000mpa.s的高取代度羧甲基瓜尔胶及其降解产物的胶液微观结构进行了表征,并且与海藻酸钠胶液的微观结构相比,显示出不同程度的结构差异。这种结构差异导致其流变行为的差异。结果显示降解高取代度羧甲基瓜尔胶与海藻酸钠胶液的微观结构及流变性能接近,在物理性能和化学性能上较为符合活性染料印花糊料的要求。     

Na、Lu掺杂Mg2Si的电子结构及光学性质的第一性原理计算

采用基于密度泛函理论的第一性原理赝势平面波方法,研究了未掺杂Mg2Si以及Na、Lu掺杂Mg2Si的电子结构和光学性质.计算结果表明:Na掺杂Mg2Si后,费米能级进入价带,呈p型导电;Lu掺杂Mg2Si后,费米能级进入导带,呈n型导电.未掺杂Mg2Si对于能量低于0.5eV的光子几乎不吸收,但Na、Lu掺杂的Mg2Si对于能量低于0.5eV的光子还存在较大的吸收,即Na、Lu掺杂改善了Mg2Si对红外光子的吸收.掺杂后,可见光区的吸收系数与反射率明显减小,这说明掺杂的Mg2Si在可见光区的透过率增大.计算结果为Mg2Si 基光电器件的设计与应用提供了理论依据.     

High-Pressure Phase Transitions of Cubic Y_2O_3 under High Pressures by In-situ Synchrotron X-Ray Diffraction

High-pressure phase transitions of cubic Y_2O_3 are investigated using in situ synchrotron x-ray diffraction in a diamond anvil cell up to 36.3 GPa. The pressure-induced phase transitions of cubic Y_2O_3, which display apparent inconsistencies in previous studies, are verified to be from a cubic phase to a monoclinic phase and further to a hexagonal phase at 11.7 and 21.6 GPa, respectively. The hexagonal Y_2O_3 displays noticeable anisotropic compressibility due to its layered structure and it is stable up to the highest pressure in the present study. A third-order Birch–Murnaghan fit based on the observed pressure-volume data yields zero pressure bulk moduli of180(3), 196(7) and 177(7) GPa for cubic, monoclinic and hexagonal phases, respectively.     

12 W high power InGaAsP/AlGaInP 755 nm quantum well laser

High power laser diodes(LDs) with a lasing wavelength between 700 and 780 nm have great potential in various medical uses. Here, we report our recent efforts in developing an InGaAsP/AlGaInP-based commercial high power edge-emitting LD, which has 755 nm emission peak with a world-record continuous wave output power of 12.7 W, the highest reported so far. The lack of Al atoms in the active region significantly lowers the chance of catastrophic optical damage during high power laser operation. Meanwhile, with an accumulated 3800 h running time, our ongoing aging tests reveal excellent reliability of our devices.     

极端工况双矩形腔静压推力轴承动态特性

静压推力轴承动态特性受润滑油黏度、油膜厚度和油腔面积等因素影响,极端工况运行过程中经常承受阶跃载荷或正弦载荷作用,突加载荷将导致静压推力轴承动态特性改变,表现为轴承的抗冲击能力和恢复平衡所需时间的变化.为获得高速重载微间隙极端工况条件下双矩形腔静压推力轴承动态特性,分别在不同油膜厚度、不同润滑油黏度以及不同油腔尺寸条件下对双矩形腔静压推力轴承的动态性能进行理论分析,探讨了阶跃载荷作用下润滑油黏度、油膜厚度和油腔面积对轴承动态性能的影响,揭示了油膜动态变化规律,探究了正弦载荷作用下双矩形腔静压推力轴承的稳定性.结果表明:润滑油黏度、油膜厚度和油腔尺寸变化对其动态性能有很大的影响.润滑油黏度越大、油膜厚度越小、油腔面积越大突加载荷作用下润滑油膜抵抗冲击的能力越强,旋转工作台受到突加外力作用下恢复至平衡状态所用时间越短.双矩形腔静压推力轴承油膜具有较大的阻尼系数,轴承具有极强的抵抗正弦加载作用的能力.     

悬链线竖向集中力作用下的构形分析和张力计算

目前,悬链线在竖向集中力和均布荷载共同作用下的构形分析和受力计算的理论仍不完善。针对这一问题,通过引入悬链线的几何约束方程、力平衡方程和超越方程,建立了竖向集中力与均布荷载共同作用下的非线性方程组。采用牛顿迭代法求解方程组,得到了悬链线的构形和受力情况。为了验证理论计算的正确性,进行了算例和试验验证。结果表明,算例的计算结果与文献结论保持一致,试验测得的构形和水平张力大小与理论计算的构形和水平张力大小吻合较好。本文的理论计算可以更加简单精确地计算出悬链线在竖向集中力和均布荷载共同作用下的构形和受力情况,为实际工程提供重要的理论指导。     

First-principles investigation on ideal strength of B2 NiAl and NiTi alloys

For B2 NiAl and NiTi intermetallic compounds, the ideal stress–strain image is lack from the perspective of elastic constants. We use first-principles calculation to investigate the ideal strength and elastic behavior under the tensile and shear loads. The relation between the ideal strength and elastic constants is found. The uniaxial tension of NiAl and NiTi along <001> crystal direction leads to the change from tetragonal path to orthogonal path, which is driven by the vanishing of the shear constant C(66). The shear failure under {110}{111} shear deformation occurring in process of tension may result in a small ideal tensile strength(~ 2 GPa) for NiTi. The unlikeness in the ideal strength of Ni Al and Ni Ti alloys is discussed based on the charge density difference.     

不确定环境下基于时间、费用及鲁棒性权衡的多目标项目调度优化

项目调度中的时间和费用是两个重要的指标,而在不确定环境下进度计划的鲁棒性则是保证项目平稳实施的关键。本文研究不确定环境下的多目标项目调度优化问题,以优化项目的工期、鲁棒值和成本为目标安排各活动的开始时间。基于此,作者构建多目标项目调度优化模型,将模型分解为三个子模型分析目标间的权衡关系,然后设计非劣排序遗传算法进行求解,应用精英保留策略和基于子模型权衡关系的优化策略优化算法,进行算法测试和算例参数敏感性分析。最后,应用上述方法研究一个项目实例,计算得到非劣解集,实例的敏感性分析结果进一步验证了三个目标间的权衡关系,据此提出资源的有效利用策略。本文的研究可以为多目标项目调度制定进度计划提供定量化决策支持。