基于SWT方法的钢绞线索微动疲劳特性分析

为得到钢绞线索丝间接触区的应力场分布并预测微动疲劳裂纹萌生位置和微动疲劳寿命，本文利用参数化方法建立了精细化的钢绞线拉索有限元模型，包括整索模型和不同层丝间接触区域的局部精细化子模型．分析了钢绞线索在两种交变荷载工况下的应力场变化情况，并基于多轴疲劳SWT(Smith-Watson-Topper)临界平面法进行了疲劳特性分析和疲劳寿命预测．主要结论如下：钢绞线索内接触区边缘处的微动幅值较大，中心处几乎没有相对滑动，微动疲劳的初始裂纹萌生点位于接触区域边缘；经不同区域子模型分析比较，在轴向循环荷载作用下，外层钢丝的接触区域比内层钢丝更易发生微动疲劳损伤；在横向位移循环荷载作用下，同层钢丝因位置角度不同而产生了较大的疲劳特性差异，且相比轴向循环拉伸，该工况下最不利单丝的微动疲劳寿命更低；与非接触区域相比，接触区的疲劳寿命大幅降低，微动现象对钢绞线索的抗疲劳性能有明显降低作用．     

Experimental and computational studies of naphthyridine derivatives as corrosion inhibitor for N80 steel in 15% hydrochloric acid

The inhibition effect of three naphthyridine derivatives namely 2-amino-4-(4-methoxyphenyl)-1,8-naphthyridine-3-carbonitrile (ANC-1), 2-amino-4-(4-methylphenyl)-1,8-naphthyridine-3-carbonitrile (ANC-2) and 2-amino-4-(3-nitrophenyl)-1,8-naphthyridine-3-carbonitrile (ANC-3) as corrosion inhibitors for N80 steel in 15% HCl by using gravimetric, electrochemical techniques (EIS and potentiodynamic polarization), SEM, EDX and quantum chemical calculation. The order of inhibition efficiency is ANC-1>ANC-2>ANC-3. Potentiodynamic polarization reveals that these inhibitors are mixed type with predominant cathodic control. Studied inhibitors obey the Langmuir adsorption isotherm. The quantum calculation is in good agreement with experimental results.     

波形钢板-UHPC组合桥面板结构截面优化

对实腹式波形顶板-UHPC(超高性能混凝土)组合桥面板进行了改进, 采用空腹式结构建立波形钢板-UHPC组合桥面板有限元模型, 研究UHPC层厚度、波形钢板厚度、波形长度、下缘板宽度和波形高度等截面参数变化对组合桥面板受力特性的影响, 并确定其合理取值范围. 在此基础上, 通过理想点法对参数组合进行优化, 得到合理的参数匹配. 研究结果表明 相较于实腹式组合桥面板, 优化后的组合桥面板自重减小35%, 钢板弯折处应力减小16%; 相较于正交异性钢桥面板, 桥面板用钢量减小7%, 顶板与U肋连接位置应力减小47%.     

Modeling and numerical simulation of the resistance spot welding of zinc coated steel sheets using rounded tip electrode: Analysis of required conditions

This paper investigates the essential conditions to improve the accuracy of a resistance spot welding computational study of advanced zinc coated steel sheets using rounded tip electrode. An experimental analysis is performed to highlight the required considerations for a suitable simulation. A sequential Electrical-Thermal-Metallurgical and Mechanical (ETMM) finite element analysis with appropriate precautions of the contact conditions enables to accurately simulate the nugget development during the welding. A critical smooth evolution of the contact radius is required. A fine meshing with an interfacial mesh size of at least 0.05 × 10⁻³ m combined with a coupling time step of 0.0025 s between the electrical-thermal-metallurgical and the mechanical analysis allows a regular incrementation of the contact radius, without burdening the time computing. Accurate values of the contact resistance depending on the interfacial pressure and temperature are essential for a good simulation of the nugget size. The ETMM calculation is successfully extended to the simulation of the welding of a typical two sheets assembly.     

Coating properties of a novel water stationary phase in capillary supercritical fluid chromatography

The coating properties of a novel water stationary phase used in capillary supercritical fluid chromatography were investigated. The findings confirm that increasing the length or internal diameter of the type 316 stainless‐steel column used provides a linear increase in the volume of stationary phase present. Under normal operating conditions, results indicate that about 4.9 ± 0.5 μL/m of water phase is deposited uniformly inside of a typical 250 μm internal diameter 316 stainless‐steel column, which translates to an area coverage of about 6.3 ± 0.5 nL/mm² regardless of dimension. Efforts to increase the stationary phase volume present showed that etching the stainless‐steel capillary wall using hydrofluoric acid was very effective for this. For instance, after five etching cycles, this volume doubled inside of both the type 304 and the type 316 stainless‐steel columns examined. This in turn doubled analyte retention, while maintaining good peak shape and column efficiency. Overall, 316 stainless‐steel columns were more resistant to etching than 304 stainless‐steel columns. Results indicate that this approach could be useful to employ as a means of controlling the volume of water stationary phase that can be established inside of the stainless‐steel columns used with this supercritical fluid chromatography technique.     

X射线荧光光谱扩展基本参数法测定不锈钢中的多种成分

针对多种类不锈钢多元素成分解析问题,应用X射线荧光光谱分析软件UniQuant,采用扩展基本参数法对多元不锈钢、双相不锈钢进行光谱干扰校正和基体校正,重新设定和优化多元不锈钢基体元素的测试条件,计算背景因子、杂质因子、谱线灵敏度系数和光谱重叠系数,测定Si、Mn、S、P、Ni、Cr、Cu、Mo、V、Al、Ti、Nb、Co、Ta、Fe的相对标准偏差在0.04%~3.8%,Ca、Zr、W、As、Sb、Sn的相对标准偏差在5.4%~20.3%,未知样品检测值与认定值比对结果相当理想,Ni、Cr的平均偏差小于0.05%,可以用很少标准样品实现各类型不锈钢多元素成分准确检测,检测范围宽,适用性好。     

钢渣与污泥协同资源化研究进展

钢渣和污泥作为传统大宗固体废弃物,始终面临处理成本高、回收利用率低等问题,但其内部含有大量可利用物质,具有较高的资源化利用价值,现已成为国内外的研究热点。为了提高钢渣与污泥绿色、高效、协同资源化利用,综述了近年来国内外钢渣在建筑、道路、水处理、农业等领域资源化利用的研究进展,立足固废无害化、减量化,从钢渣和污泥的资源化进行分析与总结,指出不同研究方法的特点和优劣,为固废资源化利用提供参考。并基于我国发展现状对钢渣与污泥资源化利用的未来发展方向进行了展望,以期为固废处理行业的良性发展提供一定的理论支撑。     

Co3O4 Decorated Ti/TiO2 Nanotubes for Photogenerated Cathodic Protection of 304 Stainless Steel

The Co₃O₄ decorated TiO₂ nanotube arrays(NTAs) coatings are fabricated by the combination of anodization and impregna-ting methods. It is found that the introduction of Co₃O₄ can reduce the diffraction intensity of (101) plane of the TiO₂ and accelerate the separation of photogenerated electron/hole pairs. In addition, the open circuit potential(OCP) and the corrosion potential of 304 stainless steel(304SS) with or without Co₃O₄ decorated TiO₂ NTAs were measured under visible light, which indicated the 304SS coupled with Co₃O₄ decorated TiO₂ NTAs had better anticorrosion performance than that of the 304SS or the 304SS coupled with pure TiO₂ NTAs. The enhancement of the cathodic protection performance of the Co₃O₄ decorated TiO₂ NTAs can be ascribed to the matched energy levels and strong interaction between Co₃O₄ and TiO₂ NTAs, and the improvement of light absorption.     

Growth of cedar-like Au nanoparticles coating on an etched stainless steel wire and its application for selective solid-phase microextraction

A novel cedar-like Au nanoparticles (AuNPs) coating was fabricated on an etched stainless steel (SS) wire by direct chemical deposition and used as an efficient and unbreakable solid phase microextraction (SPME) fiber. The etched SS wire offers a rough surface structure for subsequent growth of AuNPs in chloroauric acid solution. As a result, the uniform cedar-like AuNPs coating with larger surface area was tightly attached to the etched SS wire substrate. The AuNPs coated etched SS fiber (AuNPs/SS) was examined for SPME of ultraviolet (UV) filters, phthalate esters and aromatic hydrocarbons coupled to high-performance liquid chromatography with UV detection. The fabricated fiber exclusively exhibited excellent extraction efficiency and selectivity for some aromatic hydrocarbons. Influential parameters of extraction and desorption time, temperature, stirring rate and ionic strength were investigated and optimized. The limits of detection ranged from 0.008 μg L⁻¹ to 0.037 μg L⁻¹. The single fiber repeatability varied from 3.90% to 4.50% and the fiber-to-fiber reproducibility ranged from 5.15% to 6.87%. The recovery of aromatic hydrocarbons in real water samples spiked at 2.0 μg L⁻¹ and 20 μg L⁻¹ ranged from 94.38% to 106.2% with the relative standard deviations below 6.44%. Furthermore the growth of the cedar-like AuNPs coating can be performed in a highly reproducible manner. This fabricated fiber exhibits good stability and withstands at least 200 extraction and desorption replicates.     

Nitrogen uptake of nickel free austenitic stainless steel powder during heat treatment—an XPS study

In austenitic stainless steel nitrogen stabilizes the austenitic phase, improves the mechanical properties and increases the corrosion resistance. Nitrogen alloying enables to produce austenitic steels without the element nickel which is high priced and classified as allergy inducing. A novel production route is nitrogen alloying of CrMn‐prealloyed steel powder via the gas phase. This is beneficial as the nitrogen content can be adjusted above the amount that is reached during conventional casting. A problem which has to be overcome is the oxide layer present on the powder surface which impedes both the sintering process and the uptake of nitrogen. This study focuses on whether heat treatment under pure nitrogen is an appropriate procedure to enable sintering and nitrogen uptake by reduction of surface oxides. X‐ray photoelectron spectroscopy (XPS) in combination with scanning electron microscopy (SEM) and energy dispersive X‐ray spectrometry (EDS) are used to investigate the surface of powdered FeMn19Cr17C0.4N heat treated under nitrogen atmosphere. The analyses showed reduction of iron oxides already at 500 °C leading to oxide‐free metallic surface zones. Mn and Cr oxides are reduced at higher temperatures. Distinct nitrogen uptake was registered, and successful subsequent sintering was reached. Copyright © 2014 John Wiley & Sons, Ltd.