Mechanistic Aspects of a Highly Active Dinuclear Zinc Catalyst for the Co‐polymerization of Epoxides and CO2

The dinuclear zinc complex reported by us is to date the most active zinc catalyst for the co‐polymerization of cyclohexene oxide (CHO) and carbon dioxide. However, co‐polymerization experiments with propylene oxide (PO) and CO₂ revealed surprisingly low conversions. Within this work, we focused on clarification of this behavior through experimental results and quantum chemical studies. The combination of both results indicated the formation of an energetically highly stable intermediate in the presence of propylene oxide and carbon dioxide. A similar species in the case of cyclohexene oxide/CO₂ co‐polymerization was not stable enough to deactivate the catalyst due to steric repulsion.     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

声诱饵仿真试验系统

文章介绍了声诱饵仿真试验系统中的有关问题，包括：系统的组成、工作原理、对接装置结构等。建立了对接装置声耦合状态下的数学模型，对近场声压分布进行了仿真计算，得出了匹配材料厚度、发射和接收换能器的选取原则。     

Characterizations of Tb:Zn2SiO4 films on silicon wafer prepared by sol-gel dip-coating and solid-phase reaction

Terbium-doped Zn_2SiO_4 films were successfully prepared on Si wafers by a simple sol-gel dip-coating and solid-phase reaction method of ZnO and SiO_2. X-ray diffraction (XRD) and UV－Vis absorption results revealed that films processed below 850℃ were ZnO in wurzite structure, and films processed above 850℃ were Zn_2SiO_4 in wellimite structure. Photoluminescence measurements of the Tb-doped Zn_2SiO_4 films showed two strong emission bands at 490 and 545nm. The photoluminescence lifetime was 4.6ms.     

Stress concentration and effective stiffness of aligned fiber reinforced composite with anisotropic constituents

The paper addresses the problem of calculation of the local stress field and effective elastic properties of a unidirectional fiber reinforced composite with anisotropic constituents. For this aim, the representative unit cell approach has been utilized. The micro geometry of the composite is modeled by a periodic structure with a unit cell containing multiple circular fibers. The number of fibers is sufficient to account for the micro structure statistics of composite. A new method based on the multipole expansion technique is developed to obtain the exact series solution for the micro stress field. The method combines the principle of superposition, technique of complex potentials and some new results in the theory of special functions. A proper choice of potentials and new results for their series expansions allow one to reduce the boundary-value problem for the multiple-connected domain to an ordinary, well-posed set of linear algebraic equations. This reduction provides high numerical efficiency of the developed method. Exact expressions for the components of the effective stiffness tensor have been obtained by analytical averaging of the strain and stress fields.     

γ-辐照对纯Y_2SiO_5和Eu~(3+)∶Y_2SiO_5晶体光谱性能的影响

研究了γ-辐照前后纯Y2SiO5和Eu3+掺杂的Y2SiO5晶体吸收光谱的变化,辐照后,未退火和氢气退火的纯Y2SiO5晶体在260~270 nm和320 nm波段产生了附加吸收峰,分别是由F心和O-心的吸收引起的;经过空气退火的纯YSO晶体中,由于消除了氧空位,因此辐照后没有出现色心吸收峰。在Eu3+∶Y2SiO5晶体中,不但有相同的F心和O-心吸收峰,而且还有Eu2+离子在300 nm和390 nm的吸收峰。随着辐照剂量的增加,色心附加吸收峰增强。空气退火能减少Eu3+∶Y2SiO5晶体中的色心,而氢气退火能增加色心。     

Standardization of BSE rapid test performances and experiences gathered during the implementation of large-scale testing

The accumulation of pathological prion protein is used as a diagnostic marker for transmissible spongiform encephalopathies. According to European Union (EU) regulations cattle older than 30 months of age (Germany, France, Italy, and Spain by national law >24 months) and slaughtered for human consumption must be tested by using rapid tests for bovine spongiform encephalopathy (BSE). Likewise fallen stock and clinically affected animals must be tested. This article gives a short overview of the incidence of BSE in Europe. The diagnostic hierarchy, i.e., the officially approved methodology for the confirmation of suspect rapid test cases, and the organization of the numerous laboratories involved in this large-scale testing for BSE are described. Special emphasis is given to necessary quality control measures currently in place for BSE rapid testing laboratories and to measures intended to assure a consistent performance of the commercially available rapid test kits.Presented at BERM-9—Ninth International Symposium on Biological and Environmental Reference Materials, 15–19 June 2003, Berlin, Germany.     

Molecular dynamics simulations on the structures and properties of ε-CL-20-based PBXs ——Primary theoretical studies on HEDM formulation design

Five polymer bonded explosives (PBXs) with the base explosive ε-CL-20 (hexanitrohexaazaisowurtzi- tane), the most important high energy density compound (HEDC), and five polymer binders (Estane 5703, GAP, HTPB, PEG, and F2314) were constructed. Molecular dynamics (MD) method was employed to investigate their binding energies (Ebind), compatibility, safety, mechanical properties, and energetic properties. The information and rules were reported for choosing better binders and guiding formula- tion design of high energy density material (HEDM). According to the calculated binding energies, the ordering of compatibility and stability of the five PBXs was predicted as ε-CL-20/PEG > ε-CL-20/ Estane5703 ≈ε-CL-20/GAP > ε-CL-20/HTPB > ε-CL-20/F2314. By pair correlation function g(r) analyses, hydrogen bonds and vdw are found to be the main interactions between the two components. The elasticity and isotropy of PBXs based ε-CL-20 can be obviously improved more than pure ε-CL-20 crystal. It is not by changing the molecular structures of ε-CL-20 for each binder to affect the sensitivity. The safety and energetic properties of these PBXs are mainly influenced by the thermal capability (C°p) and density (ρ) of binders, respectively.     

Optimization of the locations of the loudspeaker and absorption material in a small room

The sound field both in the loudspeaker box and in the room is calculated by an analytical solution of three-dimensional wave equation. It is shown in theory that the amplitude response in small rooms is affected by the following positions: driver position on the front panel of the box, box position in the room, absorption material position in the box and absorption material position on the interior walls of the room. Both our computer prediction and experiments prove that the optimum positions are beneficial to the amplitude response.