SIMS of organic layers with unknown matrix parameters: Locating the interface in dual beam argon gas cluster depth profiles

Four simple methods are evaluated to determine their accuracies for establishing the interface location in secondary ion mass spectrometry intensity depth profiles of organic layers where matrix effects have not been measured. Accurate location requires the separate measurement of each ion's matrix factor. This is often not possible, and so estimates using matrix-less methods are required. Six pure organic material interfaces are measured using many secondary ions to compare their locations from the four methods with those from full evaluation with matrix terms. For different secondary ions, matrix effects cause the apparent interface positions to vary over 20 nm. The shifts in the intensity profiles on going from a layer of P into a layer of Q are in the opposite direction to that for going from Q into P, so doubling layer thickness errors. The four methods are as follows: M1, use of the median interface position in the intensity profiles for the five lightest ions for 15 ≤ m/z ≤ 150; M2, extrapolation of the position for each ion to m/z = 0 for ions with m/z ≤ 150; M3, as M2 but for m/z ≤ 300; and M4, the extreme positions for all m/z ≤ 100. Comparison with the location using matrix terms shows their ranking, from best to worst, to be M4, M3, M1, and M2 with average errors of 10%, 12%, 14%, and 17%, respectively, of the profile interface full widths at half maximum. Use of pseudo-molecular ions is very much poorer, exceeding 50%, and should be avoided.     

Stabilization of self‐assembled microdroplets using short chain alcohols

The condensation of water vapor on a volatile polymeric solution leads to a porous surface after evaporation of both solvent and water. However, the stabilization of the water microdroplet is of great importance, which can be achieved using specific polymer or adding a third substance to the polymer solution. Short chain alcohols (methanol, ethanol, and n‐propanol) are utilized to fabricate a self‐assembled porous honeycomb film of linear, low molecular weight polystyrene using the breath figure technique. A combination of breath figure processing and the effect of alcohol on a water droplet can stabilize the pattern and make pores on the surface of the polymer film. The quality of the porous honeycomb film is strongly dependent on the type of alcohols and the concentration of polymer. In a specific range of polymer and alcohol concentration, pores cover all the surface of the polymer film. This method offers the possibility of producing a honeycomb structure with no trace of additive residual after the fabrication process and avoiding polymer modification. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 709–718     

Comparison of monomethoxy‐, dimethoxy‐, and trimethoxysilane anchor groups for surface‐initiated RAFT polymerization from silica surfaces

The immobilization of reversible addition–fragmentation chain transfer (RAFT) agents on silica for surface‐initiated RAFT polymerizations (SI‐RAFT) via the Z‐group approach was studied systematically in dependence of the functionality of the RAFT‐agent anchor group. Monoalkoxy‐, dialkoxy‐, and trialkoxy silyl ether groups were incorporated into trithiocarbonate‐type RAFT agents and bound to planar silica surfaces as well as to silica nanoparticles. The immobilization efficiency and the structure of the bound RAFT‐agent film varied strongly in dependence of the used solvent (toluene vs. 1,2‐dimethoxyethane) and the anchor group functionality, as evidenced by atomic force microscopy, transmission electron microscopy, dynamic light scattering, and UV/Vis spectroscopy. Surface‐initiated RAFT polymerizations using functionalized silica nanoparticles revealed that grafted oligomers, which often occur in SI‐RAFT, are not formed within the crosslinked structures that originate from the immobilization, and that RAFT‐agent films that show less aggregation during the immobilization are more efficient during SI‐RAFT in terms of polymer grafting density. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 103–113     

Generalization of the Kelvin equation for arbitrarily curved surfaces

Capillary condensation, which takes place in confined geometries, is the first-order vapor-to-liquid phase transition and is explained by the Kelvin equation, but the equation's applicability for arbitrarily curved surface has been long debated and is severe problem. Recently, we have proposed generic dynamic equations for moving surfaces. Application of the equations to the vapor/fluid interfaces in chemical equilibrium conditions nearly trivially solves the generalization problem for the Kelvin equation. The equations are universally true for any surfaces: atomic, molecular, micro or macro scale, real or virtual, Riemannian or pseudo-Riemannian, active or passive.     

Photo-recycling the Sacrificial Electron Donor: Towards Sustainable Hydrogen Evolution in a Biphasic System

H₂ may be evolved biphasically using a polarised liquid|liquid interface, acting as a “proton pump”, in combination with organic soluble metallocenes as electron donors. Sustainable H₂ production requires methodologies to recycle the oxidised donor. Herein, the photo-recycling of decamethylferrocenium cations (DcMFc⁺) using aqueous core-shell semiconductor CdSe@CdS nanoparticles is presented. Negative polarisation of the liquid|liquid interface is required to extract DcMFc⁺ to the aqueous phase. This facilitates the efficient capture of electrons by DcMFc⁺ on the surface of the photo-excited CdSe@CdS nanoparticles, with hydrophobic DcMFc subsequently partitioning back to the organic phase and resetting the system. TiO₂ (P25) and CdSe semiconductor nanoparticles failed to recycle DcMFc⁺ due to their lower conduction band energy levels. During photo-recycling, CdS (on CdSe) may be self-oxidised and photo-corrode, instead of water acting as the hole scavenger.     

Structural and Thermodynamic Peculiarities of Core-Shell Particles at Fluid Interfaces from Triangular Lattice Models

A triangular lattice model for pattern formation by core-shell particles at fluid interfaces is introduced and studied for the particle to core diameter ratio equal to 3. Repulsion for overlapping shells and attraction at larger distances due to capillary forces are assumed. Ground states and thermodynamic properties are determined analytically and by Monte Carlo simulations for soft outer- and stiffer inner shells, with different decay rates of the interparticle repulsion. We find that thermodynamic properties are qualitatively the same for slow and for fast decay of the repulsive potential, but the ordered phases are stable for temperature ranges, depending strongly on the shape of the repulsive potential. More importantly, there are two types of patterns formed for fixed chemical potential—one for a slow and another one for a fast decay of the repulsion at small distances. In the first case, two different patterns—for example clusters or stripes—occur with the same probability for some range of the chemical potential. For a fixed concentration, an interface is formed between two ordered phases with the closest concentration, and the surface tension takes the same value for all stable interfaces. In the case of degeneracy, a stable interface cannot be formed for one out of four combinations of the coexisting phases, because of a larger surface tension. Our results show that by tuning the architecture of a thick polymeric shell, many different patterns can be obtained for a sufficiently low temperature.     

Monitoring real-time curing of epoxies in situ using single-sided NMR

Adhesively bonded joints using epoxy are widely used in aircraft and aerospace structures. Quality control and defect detection during epoxy curing in such applications is critical. We used single-sided nuclear magnetic resonance (NMR) to nondestructively probe and spatially resolve the change in the characteristic NMR relaxation time (T₂) of epoxies during curing on a substrate. Time-dependent T₂ values were fit to a Weibull function to model temporal changes in the NMR measurables. Our results demonstrate that the reduction in molecular mobility of various epoxy/curing agent mixtures occurs more rapidly at the interface than in the bulk. Further use of single-sided NMR to acquire spatially resolved T₂ data will provide a route for elucidatory epoxy curing studies. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 616–623     

Improved Interfacial Bonding Strength and Reliability of Functionalized Graphene Oxide for Cement Reinforcement Applications

Poor bonding strength between nanomaterials and cement composites inevitably lead to the failure of reinforcement. Herein, a novel functionalization method for the fabrication of functionalized graphene oxide (FGO), which is capable of forming highly reliable covalent bonds with cement hydration products, and therefore, suitable for use as an efficient reinforcing agent for cement composites, is discussed. The bonding strength between cement and aggregates was improved more than 21 times with the reinforcement of FGO. The fabricated FGO also demonstrated many important features, including high reliability in cement pastes, good dispersibility, and efficient structural refinement of cement hydration products. With the incorporation of FGO, cement mortar samples demonstrated up to 40 % increased early and ultimate strength. Such results make the fast demolding and manufacture of light constructions become highly possible, and show strong advantages on improving productivity, saving cost, and reducing CO₂ emissions in practical applications.