三元素氢氧化物中镍钴锰含量的测定

采用仪器分析方法和化学分析方法相结合测定三元前驱体Ni0.33Co0.33Mn0.33(OH)2中镍、钴、锰主含量,分别采用电感耦合等离子体原子发射光谱(ICP-AES)内标法测定镍、钴、锰的摩尔比例,EDTA滴定法测定镍、钴、锰的摩尔总量,计算得到各元素的含量。通过优化实验条件,进行了准确度和精密度实验,加标回收率为99.2%~101%,相对标准偏差小于0.65%。方法准确、快速,已用于实际的检测工作中。     

锌粉-硼砂-硼酸熔融-碘酸钾滴定法测定高硅锡精矿中的锡

针对高硅锡精矿中锡的测定时通常用锌粉-氢氧化钠熔融,精密度差,不能满足分析要求的问题,建立了锌粉-硼砂-硼酸熔融,盐酸浸取,铝粒将锡还原,碘酸钾滴定法测定高硅锡精矿中锡的分析方法。方法结果稳定,精密度好,相对标准偏差在0.19%~0.55%,加标回收率在96.9%~105%。分析结果能够满足高硅锡精矿中锡的测定要求。     

Comparison of a single-use pH test strip and a glass electrode for potentiometric titration

The potentiometric titration of a carbonate mixture or an acetate solution is a common experiment in analytical laboratories. Typically, a glass electrode combined with a calomel or Ag/AgCl reference electrode is used to locate the equivalence points in neutralization titrations. The dissociation constants of weak acids and bases can be calculated from the pH at the half-neutralization point. Recently, a new commercial product for measuring pH has been developed. This novel acid–base detection strip is a single-use sensor that requires neither storage in a preservation liquid nor calibration prior to use. This study examined its suitability for the continuous monitoring of pH changes in potentiometric titrations of carbonate mixtures, acetate solutions, or ammonia solutions. There were no significant differences in the concentrations of solutions tested using a glass electrode and a pH test strip. The pK_a, pK_b, and pH values determined using the two systems differed by less than 5%. The results confirmed that the pH strips are suitable for continuously monitoring pH changes during neutralization titrations. However, the strips can only be used once.     

全自动电位滴定法测定锂电池原料碳酸锂中主成分的含量

采用全自动电位滴定法测定锂电池原料碳酸锂中主成分的含量,用盐酸标准溶液进行滴定,考虑自动电位滴定仪的灵敏性和准确度,通过多次对比实验,确定了仪器的最佳工作参数、滴定剂浓度和样品称样量等滴定条件;对两个不同品位试样分别进行了11次平行测定,相对标准偏差(RSD)均小于1%。在碳酸锂试样中加入基准物质无水碳酸钠进行碳酸根的加标回收实验,碳酸根的加标回收率在99.4%~100%。与传统的酸碱滴定法相比,全自动电位滴定法方便、快捷,同时方法测定结果准确、可靠、精密度高,适合大批量样品快速分析。     

Na2EDTA返滴定法测定铜镍合金中的镍含量

采用Na₂EDTA返滴定法测定铜镍合金中的镍含量,用柠檬酸钠、硫代硫酸钠和酒石酸作掩蔽剂,丁二酮肟沉淀分离,以二甲酚橙为指示剂,加入过量的Na2EDTA,用氯化锌标准溶液返滴定,能很好地分离铜及其他杂质的干扰。方法用于测定铜镍合金中的镍含量,测定结果的相对标准偏差(RSD,n=9)为0.046%~0.24%,加标回收率为99.3%~101%。能够满足日常样品的检测要求。     

Quantitative determination of fucoidan using polyion-sensitive membrane electrodes

The use of polyanion and polycation-sensitive membrane electrodes to detect five different preparations of fucoidan is described. Unlike linear polyanionic molecules previously measured with polymer membrane-based electrochemical sensors, fucoidans from marine brown algae are all highly branched, sulfated polysaccharides with varying charge densities and structures, depending on the species of seaweed, method of extraction used and extent of purification. When tridodecylmethylammonium (TDMA) was used as the ion-exchanger, a large, non-equilibrium EMF response was observed over a concentration range of 0.5–50 μg mL⁻¹ fucoidan. Fucoidan was also measured by titration with polycationic protamine, using a dinonylnaphthalene sulfonate (DNNS)-doped membrane electrode as the potentiometric endpoint detector. Potentiometric titration was used to determine the binding ratio between protamine and fucoidan at the neutralization endpoint for each fucoidan preparation. This binding ratio was then used to successfully determine the fucoidan content of commercially available nutritional supplements. Fucoidan was also measured in undiluted blood serum, demonstrating that this method may be applicable for measuring fucoidan for clinical applications.     

Thermodynamic characterization of proflavine–DNA binding through microcalorimetric studies

The interaction of an important acridine dye, proflavine hydrochloride, with double stranded DNA was investigated using isothermal titration calorimetry and differential scanning calorimetry. The equilibrium constant for the binding reaction was calculated to be (1.60 ± 0.04) · 10⁵ · M⁻¹ at T = 298.15 K. The binding of proflavine hydrochloride to DNA was favored by both negative enthalpy and positive entropy contributions to the Gibbs energy. The equilibrium constant for the binding reaction decreased with increasing temperature. The standard molar enthalpy change became increasingly negative while the standard molar entropy change became less positive with rise in temperature. However, the standard molar Gibbs free energy change varied marginally suggesting the occurrence of enthalpy–entropy compensation phenomenon. The binding reaction was dominated by non-polyelectrolytic forces which remained virtually unchanged at all the salt concentrations studied. The binding also significantly increased the thermal stability of DNA against thermal denaturation.     

Influence of relative humidity and loading frequency on the PA6.6 thermomechanical cyclic behavior: Part II. Energy aspects

In this study, we investigated the influence of relative humidity (RH) and loading rate on the energy response of PA6.6 matrix specimens. The latter were subjected to oligocyclic tensile-tensile tests at 3 different RH and 2 loading rates. Infrared thermography was used to obtain a direct estimate of heat sources using the heat diffusion equation. Using the mechanical and thermal responses discussed in the first part of this work, complete energy rate balances were drawn up. In particular, the time courses of deformation, and dissipated and stored energy rates are discussed. The strong influence of the loading frequency and RH on the energy storage mechanisms is also highlighted.     

Moisture sorption in polyamide 6.6: Experimental investigation and comparison to four physical-based models

Water sorption in polyamide 6.6 has been characterized for a wide range of temperature (25°C to 80°C) and various water activities using a Dynamic Vapor Sorption testing machine. Complex sorption mechanisms govern the water uptake in the material. The competition between two main temperature dependant mechanisms has been observed: a Henry's sorption mechanism that mainly governs the sorption curve at low water activities, and a second mechanism at high water activities that could be related to the formation of water clusters. It is observed that the temperature dependency can mainly be attributed to the Henry's contribution. Four physically based models are then used and identified thanks to the extended experimental database. It is shown that a simple Flory-Huggins model is not able to capture the experimental observations at very high water activities for all the temperatures tested. The ENSIC model is a better choice, but good prediction for very high water activity cannot be obtained. Both modified Park and GAB models can accurately predict the volume fraction of water for the whole ranges of water activity and temperature, although the modified Park model should be preferred considering the number of parameters and the mathematical simplicity.     

Simultaneous Titration of Ternary Mixtures of Pb(II), Cd(II) and Cu(II) with Potentiometric Electronic Tongue Detection

An automatic titration method is reported to resolve ternary mixtures of transition metals (Pb²⁺, Cd²⁺ and Cu²⁺) employing electronic tongue detection and a reduced number of pre‐defined additions of EDTA titrant. Sensors used were PVC membrane selective electrodes with generic response to heavy‐metals, plus an artificial neural network response model. Detection limits obtained were ca. 1 mg L^?1 for the three target ions and reproducibilities 3.0 % for Pb²⁺, 4.1 % for Cd²⁺ and 5.2 % for Cu²⁺. The system was applied to contaminated soil samples and high accuracy was obtained for the determination of Pb²⁺. In the determination Cd²⁺ and Cu²⁺, sample matrix showed a significant effect.