Modifying the physicochemical properties,solubility and foaming capacity of milk proteins by ultrasound-assisted alkaline pH-shifting treatment

This study investigated the effects of different treatment of alkaline pH-shifting on milk protein concentrate (MPC), micellar casein concentrate (MCC) and whey protein isolate (WPI) assisted by the same ultrasound conditions, including changes in the physicochemical properties, solubility and foaming capacity. The solubility of milk proteins had a significant increase with gradual enhancement of ultrasound-assisted alkaline pH-shifting (p < 0.05), especially for MCC up to 99.50 %. Also, treatment made a significant decline in the particle size of MPC and MCC, as well as the turbidity of the proteins (p < 0.05). The foaming capacity of MPC, MCC, and WPI was all improved, especially at pH 11, and at this pH, the milk protein also showed the highest surface hydrophobicity. The best foaming capacity at pH 11 was the result of the combined effect of particle size, potential, protein conformation, solubility, and surface hydrophobicity. In conclusion, ultrasound-assisted pH-shifting treatment was found to be effective in improving the physicochemical properties and solubility and foaming capacity of milk proteins, especially MCC, with promising application prospect in food industry.     

Cu/CuO-Graphene Foam with Laccase-like Activity for Identification of Phenolic Compounds and Detection of Epinephrine

Although great progress has been made in the advancement of nanozymes, most of the studies focus on mimicking peroxidase, oxidase, and catalase, while relatively few studies are used to mimic laccase. However, the use of nanomaterials to mimic laccase activity will have great potential in environmental and industrial catalysis. Herein, Cu/CuO-graphene foam with laccase-like activity was designed for the identification of phenolic compounds and the detection of epinephrine. In a typical experiment, the formation mechanism of Cu/CuO-graphene foam was investigated during the pyrolysis process by thermogravimetric-mass spectrometry. As a laccase mimic, Cu/CuO-graphene foam exhibited excellent catalytic activity with a Michaelis-Menten constant and a maximum initial velocity of 0.17 mmol/L and 0.012 mmol∙L^-1∙s^-1, respectively. Based on this principle, Cu/CuO-graphene foam nanozyme could differentially catalyze phenolic compounds and 4-aminoantipyrine for simultaneous identification of phenolic compounds. Furthermore, a colorimetric sensing platform was fabricated for the quantitative determination of epinephrine, showing linear responses to epinephrine in the range of 3 mg/mL to 20 mg/mL with the detection limit of 0.2 mg/mL. The proposed Cu/CuO-graphene foam nanozyme could be applied for the identification of phenolic compounds and the detection of epinephrine, showing great potential applications for environmental monitoring, biomedical sensing, and food detection fields.     

A novel foam based separation strategy for extracting minute target impurities

The purpose of this study was to extract impurities from compounds using a simple separatory bottle to purify target compounds with a foam column and allow for the further characterization of impurities. Charged dyes were used as target compounds due to the ease of detection of dyes and isolated impurities. Foaming agents were used in a glass bottle with a modified cap to separate a target impurity using an appropriately charged ligand. By passing N₂ gas through the solution, the surfactants sodium dodecyl sulfate and cetylpyridinium chloride generated foams that separated the dyes, Methylene blue and Orange G, respectively, from a solution containing both dyes. Sodium dodecyl sulfate condensed Methylene blue from the solution with high purity while cetylpyridinium chloride condensed Orange G with less purity. A range of concentrations (0.01–0.5 mmol/L) of dyes were used for separation. The condensability (volume and/or concentration) of the target compound increased as its concentration decreased. This novel separation method is a simple, rapid, inexpensive, and effective way to prepare samples and allows for the characterization of these impurities using sensitive analytical detection techniques.     

Structure and Mechanical Stability of Epoxy Modified Polyurethane Foam Under Heat and Stress

A series of phenolic epoxy resin (PEP) modified polyurethane foams (PUF) were prepared via an in-situ polymerization, one step process. It was found that the epoxy modified PUF foam exhibited a perforated network structure with larger cell size, higher open cell porosity and enhanced ovality compared with pure PUF. With increasing content of PEP, the tensile strength, elongation at break and low temperature modulus of PUF decreased. A single T_g was observed for PEP modified PUF, indicating that the two component phases of the polyurethane-epoxy were miscible. With increasing PEP content, the T_g of PUF shifted slightly to higher temperature, tan δ_max dropped to lower values, and the retention value of the storage modulus at ?20 and ?10?°C increased. For pure PUF, the cell walls degraded and the structure became disordered after aging under heat and stress, while for PUF/20wt%PEP, the degradation degree was obviously reduced, and an orientation of the cells along the stress direction and a density increase was observed. During aging at 200?°C, the retention of the mechanical properties of PUF/20wt% PEP was much higher than that of pure PUF, and it showed superior stability under heat and stress, attributed to incorporation of the thermally resistant oxazolidone rings and benzene rings in the PU backbones, the highly cross-linked networks of the polyurethane-epoxy systems and the obvious orientation of the cells under stress.     

改性二氧化硅纳米颗粒提高二氧化碳泡沫稳定性的研究

通过纳米二氧化硅的硅烷化改性, 使其在高矿化度盐水中可以稳定存在的前提下, 研究了改性纳米颗粒与阳离子表面活性剂十二烷基三甲基氯化铵混合体系的溶液稳定性及协同稳定CO₂泡沫的效果. 研究结果表明, 无机盐离子对改性纳米颗粒与阳离子表面活性剂间的静电吸引力具有屏蔽作用, 且矿化度越高, 屏蔽效果越明显, 从而混合溶液更易于在高盐水中稳定; 纳米颗粒表面的活性剂吸附层受二者浓度的影响, 进而影响了颗粒的亲/疏水性; 当混合体系中的表面活性剂浓度低于临界胶束浓度(CMC)时, 混合溶液与CO₂的界面张力高于单独活性剂溶液, 而当活性剂浓度高于CMC时, 对CO₂-溶液界面张力几乎无影响, 最低界面张力可降至6 mN/m左右; 改性纳米颗粒的加入可以进一步提高CO₂体相泡沫半衰期一倍以上, 但受二者浓度比例的影响; 纳米颗粒的加入有效提高了多孔介质中泡沫的表观黏度, 最大增幅由20 mPa·s增至55 mPa·s左右, 泡沫黏度增加接近3倍, 增强了CO₂泡沫驱的封堵作用.     

Self‐assembled polyurea macromer nanodispersion and resulting hybrid polyurea‐acrylic emulsions and films

A polyurea macromer (PUM) was synthesized and dispersed in basic conditions to form self‐assembled nanoparticles (<20 nm dispersions, up to 30 wt % aq. soln.). These nanoparticles enabled surfactant‐free emulsion polymerization to form hybrid polyurea‐acrylic particles despite the absence of a measureable water‐soluble fraction. The T_g of the starting PUM material was a strong function of the PUM's extent of neutralization and hydration (varying between 100 °C and >175 °C) due to changes in hydrogen and ionic bonding. Two separate hybrid polyurea‐acrylic emulsion systems were prepared: one by direct polymerization of (meth)acrylic monomers in the presence of the nanodispersion and a second by a physical blend of PUM nanodispersion with an acrylic latex control. The direct polymerization method resulted in a hybrid emulsion particle size that developed by a mechanism resembling conventional emulsion polymerization and was unlike that described for seeded polyurethane dispersion systems. Film hardness was shown to increase with increasing coating thickness for the hybrid film prepared by direct polymerization. The resulting mechanical properties could be explained by applying mechanical models for a composite foam structure. These results were unprecedented for normal elastomer films. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1373–1388     

Sol-Gel Microspheres Doped with Glycerol: A Structural Insight in Light of Forthcoming Applications in the Polyurethane Foam Industry

Porous silica-based microspheres encapsulating aqueous glycerol can be potential curing agents for one-component foams (OCFs). Such agents have the advantage of an enhanced sustainability profile on top of being environmentally friendly materials. A synthetically convenient and scalable sol-gel process was used to make silica and organosilica microspheres doped with aqueous glycerol. These methyl-modified silica microspheres, named “GreenCaps”, exhibit remarkable physical and chemical stability. The microspheres were characterized by scanning electron microscopy, transmission electron microscopy at reduced pressure, and cryogenic nitrogen adsorption—desorption analysis. The structure of the materials was also analyzed at the molecular level by diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy. As expected, the degree of methylation affects the degree of encapsulation and pore structure. Microspheres similarly methylated, however, can differ considerably in surface area and pore size due to the templating effect of glycerol on the organosilica structure. The results of the structure analysis reveal that glycerol is efficiently encapsulated, acts as a template, barely leaches over time, but is released by depressurization. A proper application of these microspheres can later on enhance both the environmental and health profile, as well as the technical performance (curing speed, foam quality, and froth thixotropy) of spray polyurethane foams.     

Effects of Charged Surfactants on Interfacial Water Structure and Macroscopic Properties of the Air-Water Interface

Surfactants are used to control the macroscopic properties of the air-water interface. However, the link between the surfactant molecular structure and the macroscopic properties remains unclear. Using sum-frequency generation spectroscopy and molecular dynamics simulations, two ionic surfactants (dodecyl trimethylammonium bromide, DTAB, and sodium dodecyl sulphate, SDS) with the same carbon chain lengths and charge magnitude (but different signs) of head groups interact and reorient interfacial water molecules differently. DTAB forms a thicker but sparser interfacial layer than SDS. It is due to the deep penetration into the adsorption zone of Br⁻ counterions compared to smaller Na⁺ ones, and also due to the flip-flop orientation of water molecules. SDS alters two distinctive interfacial water layers into a layer where H⁺ points to the air, forming strong hydrogen bonding with the sulphate headgroup. In contrast, only weaker dipole-dipole interactions with the DTAB headgroup are formed as they reorient water molecules with H⁺ point down to the aqueous phase. Hence, with more molecules adsorbed at the interface, SDS builds up a higher interfacial pressure than DTAB, producing lower surface tension and higher foam stability at a similar bulk concentration. Our findings offer improved knowledge for understanding various processes in the industry and nature.