MCNOs/CdS双效光催化剂的制备及其性能研究

水热合成法制备了不同磁性纳米洋葱碳(MCNOs)负载量(0%、1%、3%、5%)的MCNOs/CdS光催化剂。并通过X射线衍射分析(XRD)、扫描电子显微镜(SEM)、傅里叶红外光谱(FT-IR)、X射线光电子能谱(XPS)、紫外可见光光谱(UV-Vis)、磁滞回线测定仪(VSM)对其进行表征,探究了MCNOs负载比例对催化剂在可见光下降解RhB性能及机理的影响。结果表明,MCNOs能有效提高CdS的光催化效果,复合3%MCNOs后降解率为96%,与纯CdS相比降解率提高了30%,磁性分析表明,其具有良好的顺磁性并能实现催化剂的有效回收。MCNOs/CdS在可见光下催化降解RhB的一级反应动力学直线有较好的拟合度,表明制备的催化剂有较好的催化活性。     

Sonochemical conversion of CO2 into hydrocarbons: The Sabatier reaction at ambient conditions

In this study, we investigated an alternative method for the chemical CO₂ reduction reaction in which power ultrasound (488 kHz ultrasonic plate transducer) was applied to CO₂-saturated (up to 3%) pure water, NaCl and synthetic seawater solutions. Under ultrasonic conditions, the converted CO₂ products were found to be mainly CH₄, C₂H₄ and C₂H₆ including large amount of CO which was subsequently converted into CH₄. We have found that introducing molecular H₂ plays a crucial role in the CO₂ conversion process and that increasing hydrogen concentration increased the yields of hydrocarbons. However, it was observed that at higher hydrogen concentrations, the overall conversion decreased since hydrogen, a diatomic gas, is known to decrease cavitational activity in liquids. It was also found that 1.0 M NaCl solutions saturated with 2% CO₂ + 98% H₂ led to maximum hydrocarbon yields (close to 5%) and increasing the salt concentrations further decreased the yield of hydrocarbons due to the combined physical and chemical effects of ultrasound. It was shown that CO₂ present in a synthetic industrial flue gas (86.74% N₂, 13% CO₂, 0.2% O₂ and 600 ppm of CO) could be converted into hydrocarbons through this method by diluting the flue gas with hydrogen. Moreover, it was observed that in addition to pure water, synthetic seawater can also be used as an ultrasonicating media for the sonochemical process where the presence of NaCl improves the yields of hydrocarbons by ca. 40%. We have also shown that by using low frequency high-power ultrasound in the absence of catalysts, it is possible to carry out the conversion process at ambient conditions i.e., at room temperature and pressure. We are postulating that each cavitation bubble formed during ultrasonication act as a “micro-reactor” where the so-called Sabatier reaction -$C{O}_2+4H_2\stackrel{\mathit{Ultrasonication}}{\to }C{H}_4+2H_{2}O$ - takes place upon collapse of the bubble. We are naming this novel approach as the “Islam-Pollet-Hihn process”.     

Distribution dependent stochastic differential equations

Due to their intrinsic link with nonlinear Fokker-Planck equations and many other applications, distribution dependent stochastic differential equations (DDSDEs) have been intensively investigated. In this paper, we summarize some recent progresses in the study of DDSDEs, which include the correspondence of weak solutions and nonlinear Fokker-Planck equations, the well-posedness, regularity estimates, exponential ergodicity, long time large deviations, and comparison theorems.     

基于XPS对硫铁矿去除SeO2-3的机理研究

硒是动植物及人体生长必需的十五种微量元素之一，具有清除体内自由基、抗氧化、增强免疫力等功能，但其安全剂量的范围却很窄。利用扫描电子显微镜（SEM）和X射线衍射仪（XRD）对湿法球磨制备的硫铁矿形貌进行了表征。SEM观测发现加乙醇助磨后的硫铁矿为粒径大小较均匀的球形颗粒团聚体，粒径范围在17～200 nm之间，平均粒径138 nm。XRD衍射图谱中的特征峰与FeS₂衍射图谱中各峰位置基本一致，因此判定硫铁矿中主要化学组分为FeS₂，且图谱中基本没有杂峰，表明制备过程中并未混入杂质，样品纯度较高。实验结果表明，该法制备的硫铁矿具有颗粒粒径小、比表面积大、反应活性高等优点。研究中利用X射线光电子能谱仪（XPS）对硫铁矿去除水体中SeO2-₃的机理进行了研究。研究结果表明, （1）在较为广泛的实验pH范围（pH 2.2～11.5），硫铁矿均能有效去除水体中SeO2-₃，去除效率（除pH值7.8以外）均达到90%以上；（2）硫铁矿与SeO2-₃发生反应后，其主要组成元素的XPS特征峰结合能有所减小，表明硫铁矿表面发生了一定化学变化；（3）酸碱环境下硫铁矿去除SeO2-₃的机理不完全相同，酸性环境下，硫铁矿对SeO2-₃的去除是单纯的氧化还原过程，即硫铁矿中被酸活化的S2-₂将SeO2-₃还原为单质Se(0)，并且酸性越强，SeO2-₃去除效果越好；碱性环境下，SeO2-₃的去除过程中氧化还原与络合反应并存，硫铁矿表面有络合态Fe(OH)SeO₃和单质Se(0)两种存在形态，且碱性越强，络合态Fe(OH)SeO₃含量越高。以上研究结果为硫铁矿去除固定水体和土壤中以SeO2-₃为代表的可变价金属阴离子提供重要理论依据和应用基础。     

移动加热器法生长碲锌镉晶体的组分输运与界面形貌研究

移动加热器法(THM)生长碲锌镉晶体时,界面稳定性对晶体生长的质量有很大影响。本文基于多物理场有限元仿真软件Comsol建立了THM生长碲锌镉晶体的数值模拟模型,讨论了Te边界层与组分过冷区之间的关系,对不同生长阶段的物理场、Te边界层与组分过冷区进行仿真研究,最后讨论了微重力对物理场分布的影响,并对比了微重力与正常重力下的生长界面形貌。模拟结果表明,Te边界层与组分过冷区的分布趋势是一致的,在不同生长阶段,流场中次生涡旋的位置会发生移动,从而导致生长界面的形貌随着生长的进行发生变化,同时微重力条件下形成的生长界面形貌最有利于单晶生长。因此,在晶体生长的中前期,对次生涡旋位置的控制和对组分过冷的削弱,是THM生长高质量晶体的有效方案。     

Synthesis of 29H,31H-phthalocyanine and chloro (29H,31H-phthalocyaninato) aluminum derivatives showed anti-cancer and anti-bacterial actions

Continuous administration of most chemotherapeutic drugs can induce different types of side effects. There has been growing interest in exploring an alternative approach to synthesizing compounds that are most effective and have fewer side effects. We synthesized 29H,31H-Phthalocyanine, and Chloro (29H,31H- phthalocyaninato) aluminum at low temperatures using lithium in the present study with diisopropylamide as the nucleophile. The physical characteristics of 29H,31H-Phthalocyanine, and Chloro (29H,31H- phthalocyaninato) aluminum were confirmed by FT-IR method, XRD, SEM, and the impact of these compounds on human colorectal carcinoma (HCT-116) and human cervical cells (HeLa) was examined. Treatment with 29H,31H-Phthalocyanine significantly decreased cancer cell growth and proliferation, as determined by MTT and DAPI staining analysis. In contrast, Chloro (29H,31H- phthalocyaninato) aluminum treatment did not show any inhibitory action on colon or cervical cancer cells. We also calculated the inhibitory concentration (IC50) of 29H,31H-Phthalocyanine, which was 30 µg/ml (HCT-116) and 33 µg/ml (HeLa cells). The antibacterial effectiveness of 29H,31H-Phthalocyanine, and chloro (29H,31H- phthalocyaninato) aluminum was studied using Enterococcus faecalis (E. faecalis). The CFU (colony frequency unit) assay confirmed significant activity against the test bacterium after treatment with 29H,31H-Phthalocyanine. However, no activity was seen upon treatment with chloro (29H,31H- phthalocyaninato) aluminum against E. faecalis.     

非富勒烯受体DA'D型稠环单元的结构修饰及电池性能研究

近年来,设计和合成高性能非富勒烯受体(NFAs)材料已经成为太阳能电池研究领域的前沿课题。基于DA'D型稠环结构的NFAs由于具有吸光系数高、能级和带隙可调、结构易于修饰、分子可高效合成、光电学性能优异等优点而受到了越来越广泛的关注。在短短7年的时间里,能量转换效率(PCE)从3%~4%提高到18%。2019年初邹应萍等报道了一个优秀的受体分子Y6,与PM6共混制备单结电池,获得了15.7%的能量转换效率。Y6类受体材料的中心给电子单元为DA'D型稠环结构,缺电子单元(A')通过氮原子与两个给电子单元(D)并联形成稠环结构,这有助于降低前线分子轨道能级并增强吸收,同时与氮相连的两个烷基链和位于噻吩并噻吩β位的两个侧链则有助于提高溶解度及调节结晶性。自Y6问世以来,人们对分子的结构剪裁进行了深入的研究,并报道了数十种新的结构。在这些新的受体中,DA'D部分的结构裁剪对提高器件效率和太阳能电池的性能起着至关重要的作用。本文对A'、D单元和侧链结构修饰的研究进展进行了综述。通过选择几组受体,对最近报道的分子进行分类,并将它们的光学、电化学、电学和光电性质与精确的结构修饰相关联,从而对结构-性能关系进行全面概述。     

Enhanced Power Density of Alcohol Biofuel Cell by Polymer-assisted Crosslinks of 3D Graphene on Carbon Paper as the Bioanode

Herein, we successfully construct the 3D biocompatible graphene through crosslinking 2D graphene nanosheet onto carbon fiber paper with poly(diallyldimethylammonium chloride) (PDDA) as anode of the alcohol biofuel cell. Compared with the bioanode without 3D graphene, the current density and output power of PDDA-graphene-ADH bioanode is increased by 23 % and 41 % at a high concentration of ethanol at pH 8.9, suggesting the stabilization role of graphene in enzyme loading. The study provides us a deep analysis on structures and performances of the bioanode incl. electrochemistry, X-ray photoelectron spectra, and atomic force microscopy images, which is significant to develop the new methods to construct 3D porous electrodes in energy conversion device.     

One-pot,one-step,and selective terpolymerization of ethylene oxide,propylene oxide,and COS to copoly(thioether)s with tunable thermal properties

Facile construction of sulfur-rich polymers using readily available raw chemicals is an area aggressively pursued but challenging. Herein we use common feedstocks of ethylene oxide (EO), propylene oxide (PO), and carbonyl sulfide (COS) to synthesize copoly(thioether)s which are traditionally produced from unpleasant and difficult to store episulfides. In this protocol, the EO/COS coupling selectively generates a pure poly(ethylene sulfide) (PES) with melting temperature (T_m) values up to 172°C and high yields up to 98%. The EO/PO/COS terpolymerization leads to the incorporation of soft poly(propylene sulfide) (PPS) and hard PES segments together, affording a random PES-co-PPS copoly(thioether) with the complete consumption of EO and PO. Additionally, by simply varying the EO/PO feeding ratio, the obtained copoly(thioether)s possess tunable thermal properties, T_m values in the range of 76–144°C, and excellent solubility. These copolymerizations are conducted in one-pot/one-step at industrially favored reaction temperatures of 100–120°C using catalysts of common organic bases, suggesting a facile and practical manner. Especially, the copoly(thioether) exhibits high refractive indices up to 1.68 owing to its high sulfur content, suggesting a broad application prospect in optical materials.