气相输运沉积制备c轴择优取向的碘化铋薄膜

铋基卤化物材料因其无毒和优良的光电性能而显示出巨大的应用潜力。BiI₃作为一种层状重金属半导体,已被用于X射线检测、γ射线检测和压力传感器等领域,最近其作为一种薄膜太阳能电池吸收材料备受关注。本文采用简单的气相输运沉积(VTD)法,以BiI₃晶体粉末作为蒸发源,在玻璃基底上得到高质量c轴择优取向的BiI₃薄膜。并通过研究蒸发源温度和沉积距离对薄膜物相和形貌的影响,分析了BiI₃薄膜择优生长的机理。结果表明VTD法制备的BiI₃薄膜属于三斜晶系,其光学带隙为~1.8 eV。沉积温度对薄膜的择优取向有较大影响,在沉积温度低于270 ℃时,沉积的薄膜具有沿c轴择优取向生长的特点,超过此温度,c轴择优取向生长消失。在衬底温度为250 ℃、沉积距离为15 cm时制备的薄膜结晶性能最好,晶体形貌为片状八面体。     

Y掺杂WS2二维材料的第一性原理研究

WS₂由于其优异的物理和光电性质引起了广泛关注。本研究基于第一性原理计算方法,探索了本征单层WS₂及不同浓度W原子替位钇(Y)掺杂WS₂的电子结构和光学特性。结果表明本征单层WS₂为带隙1.814 eV的直接带隙半导体。进行4%浓度(原子数分数)的Y原子掺杂后,带隙减小为1.508 eV,依旧保持着直接带隙的特性,随着Y掺杂浓度的不断增大,掺杂WS₂带隙进一步减小,当浓度达到25%时,能带结构转变为0.658 eV的间接带隙,WS₂表现出磁性。适量浓度的掺杂可以提高材料的导电性能,且掺杂浓度增大时,体系依旧保持着透明性并且在红外光和可见光区对光子的吸收能力、材料的介电性能都有着显著提高。本文为WS₂二维材料相关光电器件的研究提供了理论依据。     

Design of Functional Carbon Composite Materials for Energy Conversion and Storage

The carbon composite materials have been a research hotspot in the fields of catalysis, energy conversion and so on, because of their features of large structure and morphology variety, good chemical and electrochemical stability, and high electronic conductivity, large specific surface area and rich active sites. This paper summarizes some research progress of carbon composite materials, including assembly methodologies, their structure regulation, properties, and related applications. Moreover, the current challenges and the prospects of these materials are also discussed.     

Rice husk silica as a sustainable filler in the tire industry

In this paper, we studied commercially available precipitated rice husk silica (RHS) with conventional precipitated silica, which has nearly the same surface area, and replaced part of the carbon black with RHS and conventional silica in a basic tread formulation. All formulations were mixed with the same amount of filler during the study. Silica was used at 15, 30 and 50 phr loading, and part of the carbon black was replaced by silica. Compound curing characteristics, physical properties, rebound resilience, heat generation, abrasion loss, dynamic properties and morphology were analyzed. The results indicated that RHS demonstrated compound properties comparable to those of conventional silica. As part of the carbon black was replaced with conventional silica, a slower cure rate, higher rebound resilience, lower heat generation, lower abrasion loss, and lower tan delta were observed with no significant change in physical properties, but some changes in physical properties were observed using one way ANOVA analysis. We found the same trend when replacing part of the carbon black with RHS, such as a slower cure rate, higher rebound resilience, lower heat generation, lower abrasion loss, and lower tan delta with no significant change in physical properties, but some changes in physical properties were observed using one way ANOVA. This sustainable material could be used to replace conventional silica in tire compounding, as well as to replace a portion of carbon black with RHS for improved heat build-up, rolling resistance, and abrasion loss.     

水热法制备二氧化锡/钨酸铋复合光催化材料及其催化活性研究

本文用水热法制备了正交晶系的纳米球状结构的二氧化锡和正交晶系的由片状聚集成球状结构的钨酸铋,并且对二者进行了复合,制备出了二氧化锡/钨酸铋复合光催化材料。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、比表面积测试仪(BET)、紫外可见分光光度计等技术对复合样品的结构、形貌、比表面积、孔容孔径和光学性质进行了表征。用碘钨灯模拟太阳光,分别以二氧化锡、钨酸铋和二氧化锡/钨酸铋复合材料为催化剂降解罗丹明B(RhB),研究所制备的二氧化锡/钨酸铋复合材料的光催化活性。光催化90 min时二氧化锡、钨酸铋和二氧化锡/钨酸铋对罗丹明B的降解率分别是9%、22%和30%。实验结果表明,在可见光下,二氧化锡/钨酸铋复合材料的光催化活性要高于单一的二氧化锡和钨酸铋。     

Hybrid cyclotriphosphazene–polysiloxane–nano-SiO2 composites with improved mechanical properties

Starting from the functional cyclotriphosphazene, polysiloxane and nano-SiO₂ precursors, three new hybrid nanocomposites with reinforced mechanical properties were prepared. Young’s modulus values for all the composite samples are similar in the range of 7–11 MPa, stress at fracture increases with the nano-SiO₂ content increase in the material and reaches a maximum value of 36 MPa for the composite with 20% nano-SiO₂. The nanocomposites investigated are elastic and demonstrate the ability to be deformed without failure up to 54% strain.     

新型功能碳材料的高压截获

高性能功能材料在诸多领域具有广泛的应用前景,是人们一直关注的研究热点。高压可以有效地改变物质的原子间距和成键方式,是获得新型功能材料的重要途径。在碳材料的高压研究中,许多有趣的功能碳材料,如光学透明碳、高强度弹性碳和超硬非晶碳等,已经通过不同的碳前驱体合成。本文简要介绍了作者近年来在低维碳基纳米复合材料高压研究中取得的进展,基于设计的不同低维碳前驱体,高压下截获了具有超硬特性、新型压致共价聚合及发光增强的碳材料。     

Performance evaluation of functionalized ordered mesoporous silica for VOCs adsorption by molecular dynamics simulation

Volatile organic compounds (VOCs) are growing pollutants now that cause the serious environmental pollution and threaten human health. The functionalized ordered mesoporous silica (FOMS) has attracted considerable attention in adsorbing VOCs. In this paper, the molecular dynamics simulation was used to simulate the adsorption performance of FOMS on VOCs (acetone, ethyl acetate and toluene). After simulating different pore sizes (2 nm, 3 nm and 4 nm) adsorption performances of ordered mesoporous silica (OMS) on VOCs, OMS with a pore size of 4 nm was selected to further study the influence of functional groups (vinyl, methyl, and phenyl). The following law was obtained: the saturated adsorption capacities of vinyl-functionalized OMS (V-FOMS) to acetone, ethyl acetate and toluene were 3.045 mmol.g^?1, 2.568 mmol.g^?1 and 1.976 mmol.g^?1 respectively; the saturated adsorption capacities of methyl-functionalized OMS (M-FOMS) to acetone, ethyl acetate and toluene were 2.798 mmol.g^?1, 2.312 mmol.g^?1 and 1.698 mmol.g^?1 respectively; the saturated adsorption capacities of phenyl-functionalized OMS (P-FOMS) to acetone, ethyl acetate and toluene were 2.124 mmol.g^?1, 1.941 mmol.g^?1 and 1.539 mmol.g^?1 respectively. These results show that the adsorption ability of FOMS for different adsorbates follows the sequence of acetone > ethyl acetate > toluene. Furthermore, the interaction between functional groups (vinyl, methyl and phenyl) in FOMS and VOCs was explored. It is found that the interaction between different functional groups and adsorbates is different (interaction energy effect). This interaction energy effect promotes FOMS to better adsorb VOCs. This work would provide fundamental understanding and guidance for the development of novel adsorption materials for the adsorption of VOCs.     

A self-powered and sensitive terahertz photodetection based on PdSe2

With the rapid development of terahertz technology, terahertz detectors are expected to play a key role in diverse areas such as homeland security and imaging, materials diagnostics, biology, medical sciences, and communication. Whereas self-powered, rapid response, and room temperature terahertz photodetectors are confronted with huge challenges. Here, we report a novel rapid response and self-powered terahertz photothermoelectronic (PTE) photodetector based on a low-dimensional material: palladium selenide (PdSe₂). An order of magnitude performance enhancement was observed in photodetection based on PdSe₂/graphene heterojunction that resulted from the integration of graphene and enhanced the Seebeck effect. Under 0.1-THz and 0.3-THz irradiations, the device displays a stable and repeatable photoresponse at room temperature without bias. Furthermore, rapid rise (5.0 μs) and decay (5.4 μs) times are recorded under 0.1-THz irradiation. Our results demonstrate the promising prospect of the detector based on PdSe₂ in terms of air-stable, suitable sensitivity and speed, which may have great application in terahertz detection.     

Design of broadband achromatic metasurface device based on phase-change material Ge2Sb2Te5

Based on the phase-change material Ge₂Sb₂Te₅ (GST), achromatic metasurface optical device in the longer-infrared wavelength is designed. With the combination of the linear phase gradient GST nanopillar and the adjustment of the crystalline fraction m value of GST, the polarization insensitive achromic metalenses and beam deflector metasurface within the longer-infrared wavelength 9.5 μm to 13 μm are realized. The design results show that the achromatic metalenses can be focused on the same focal plane within the working waveband. The simulation calculation results show that the full-width at half-maximum (FWHM) of the focusing spot reaches the diffraction limit at each wavelength. In addition, the same method is also used to design a broadband achromatic beam deflector metasurface with the same deflection angle of 19°. The method proposed in this article not only provides new ideas for the design of achromatic metasurfaces, but also provides new possibilities for the integration of optical imaging, optical coding and other related optical systems.