A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

Proteinases from Carica papaya Latex

Data on the proteinase complex from Carica papaya latex were reviewed. The properties and applications of the domestic preparation cucumazyme and known medicinal preparations based on papaya proteinases (caripazyme, lecozyme, lecopain) were compared.     

Adhesion studies of latex film surfaces on the meso- and nanoscale

In this paper the effects of surface roughness and annealing temperature (T) of latex coating films on adhesion are discussed for the different stages of the film formation process. The surface free energy of latex films was assessed in terms of practical work of adhesion (W) (or adherence) using a custom-built adhesion-testing device (ATD), atomic force microscopy (AFM), and contact angle measurements. For preannealed latex films surface roughness averages (R_a) were determined from AFM height images and were related to the values of W obtained from ATD measurements at room temperature. The results obtained using these tests exhibiting surface behavior on different length scales indicate a dependence of the measured adhesion on surface roughness and temperature, as well as on the length scale of the measurements.First preannealed samples were studied, which were obtained by heat treatment above the respective glass transition temperatures (T_g). Increasing the temperature of preannealing resulted in a decrease of the adherence observed in ATD experiments at room temperature. However, on the nanoscale, using AFM, no significant variation of the adherence was observed. This observation can be explained by roughness arguments. Preannealing decreases roughness which results in lower adherence values measured by ATD while for essentially single asperity AFM experiments roughness has an insignificant effect. Specimens were also annealed over a constant period of time (90 min) at different temperatures. At the end of the heat treatment, adhesion was measured at the treatment temperature by ATD. The amplified effect of temperature observed in this case on adherence is attributed to the combination of roughness decrease and increasing test temperature. In a third set of experiments completely annealed samples were studied by ATD as well as by AFM as a function of temperature. With increasing T values ATD showed a decrease in adherence, which is attributed to a decreasing surface free energy of the annealed films at elevated T values. AFM, on the other hand, showed an opposite trend which is assigned to increasing penetration of the tip into the tip/wetting polymer samples versus increasing temperature. Finally, annealing isotherms as a function of time were investigated by ATD in situ at different temperatures. This last set of experiments allowed us to optimize annealing time and temperature to achieve complete curing.     

乳液聚合阶段Ⅱ动力学研究的进展

本文简述了乳浓聚合动力学研究的进展,着重于澳大利亚Sydney大学Gilbert等在乳液聚合阶段Ⅱ动力学方面的研究概况。介绍了不同水溶性单体的小尺寸种子乳液体系的SmithEwart递推方程的求解方法及其解析解形式和乳液聚合动力学数据的处理。同时讨论了该研究的局限性。     

Structural morphology of poly(styrene)-poly(butyl acrylate) polymer-polymer composites studied by dynamic mechanical measurements

The emulsion polymerization process allows production of polymer particles with different structural morphologies. Films obtained after coalescence keep some memory of this morphology, but large modifications can occur during coalescence. In the present case, one of the polymers, polystyrene (PS), exhibits a glass temperature (Tg) much higher than the filmification temperature (close to room temperature), while the other one, poly(butyl acrylate) (PBA), has a much lowerTg. Furthermore, it is well known that dynamic mechanical measurements can be very helpful in providing information on the morphology of polymer materials, i.e., on geometrical and topological arrangement of homopolymer domains. At first, this method was used for comparison of two types of films: i) the first one obtained from structured-core (PS)-shell (PBA) particles, ii) the second one obtained from a blend of homopolymer particles (PS and PBA). It appears that the expected core-shell particles lost their geometric structure in the second film. Second, comparison of the predicted dynamic modulus and experimental data shows that i) strong interactions exist between PS nodules unless their coalescence has occured, leading to an abnormally high modulus at room temperature, ii) after achieving their coalescence, PS forms a more or less continuous phase. Both phenomena strongly depend on the particle size and their respective volume fractions.     

Structural anisotropy in friction‐deposited layers of polystyrene

Friction‐deposited layers of atactic polystyrene (PS) on inert and OH‐grafted gold substrates were the subject of this study to establish a relationship between the friction process and the resulting anisotropy of the transferred polymer chains. We show, by using polarization‐modulation infrared reflection‐absorption spectroscopy that the deposited PS chains involve an anisotropy in which PS main backbone is rather perpendicular to the friction support, fact that is surprising when compared with the majority of polymers where the anisotropy is along the sliding direction. Moreover, our calculation of the orientation angles revealed that PS chains are more perpendicular in the transferred layers than in spin‐coated films. This particular anisotropy is probably due to a parallel reorientation of the phenyl ring on the friction support whatever the surface chemistry is. On the other hand, this study was useful to rectify the assignment of infrared bands unclearly reported in the literature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3272–3281, 2006     

甲基丙烯酸全氟烷基代乙酯对天然橡胶乳液辐射改性研究

天然橡胶的性能与其组成中的C C双键有密切关系,由于C C双键的存在,为天然橡胶的改性提供了便利,大多数天然橡胶的改性方法,如氯化、氢氯化、环化、环氧化、接枝共聚等皆是建立在这一思路基础上的.White等[1]认为接枝天然橡胶的目的是提高天然橡胶的机械强度,赋予特殊的功能.作     

Preparation of HPMC–EA–DMAEMA nanosized latex

Nanosized copolymer latex of hydroxypropylmethylcellulose (HPMC) grafted with ethyl acrylate (EA) and dimethylaminoethyl methacrylate (DMAEMA) has been prepared by acidifying submicron-sized latex particles synthesized by soap-free emulsion graft copolymerization using potassium persulfate (KPS) as initiator. The effects on the diameter of the latex particles of different conditions, for example concentration of DMAEMA, amount of HPMC, and ratio of HCl to DMAEMA for acidification, were investigated. It was found that increasing the mole ratio of HCl to DMAEMA to 1.0 and increasing the DMAEMA content both resulted in a decrease in particle diameter, whereas increasing the amount of HPMC resulted in larger particle sizes. Measurement by dynamic light scattering (DLS) revealed the diameter of the latex particles was >200 nm before acidification and <100 nm after acidification. Evidence of grafting was obtained by use of Fourier transform infrared (FTIR) spectroscopy. Transmission electron microscopy (TEM) was used to characterize the morphology of the copolymer particles before and after acidification.