Thermodynamic and kinetic aspects on the selective surface oxidation of binary, ternary and quarternary model alloys

Segregation and selective oxidation phenomena of minor alloying elements during annealing of steel sheets lead to the formation of bare spots after hot dip galvanizing. In order to understand the influence of common alloying elements on the surface chemistry after annealing, model alloys of binary (Fe-2Si, Fe-2Mn and Fe-0.8Cr), ternary (Fe-2Mn-2Si, Fe-2Mn-0.8Cr and Fe-2Si-0.8Cr) and quarternary (Fe-2Mn-2Si-0.8Cr) systems were investigated. The specimens were annealed for 60 s at 820 °C in N₂-5% H₂ gas atmospheres with different dew points −80 and −40 °C, respectively. Surface chemistry of the annealed specimens was obtained by using X-ray photoelectron spectroscopy (XPS). The field emission scanning electron microscopy (FE-SEM) was used to view surface morphology. At low dew point −80 °C, apart from the thermodynamical calculations such as solubility product of oxides and their critical solute concentrations, kinetics play a decisive role on the selective oxidation, i.e. oxygen competition. As expected, the amount of external selective oxidation of alloying elements are well pronounced at higher dew point −40 °C. An attempt has been made to explain the dominant process of Si and Mn on Cr-oxidation and segregation. It is observed that annealing of quarternary system at higher dew point shifts the Cr-oxidation from external to internal.     

Relation of structure to performance characteristics of monolithic and perfusive stationary phases

Commercially available polymer-based monolithic and perfusive stationary phases were evaluated for their applicability in chromatography of biologics. Information on bed geometry, including that from electron microscopy (EM), was used to interpret and predict accessible volumes, binding capacities, and pressure drops. For preparative purification of biologics up to at least 7 nm in diameter, monoliths and perfusive resins are inferior to conventional stationary phases due to their low binding capacities (20–30 g/L for BSA). For larger biologics, up to several hundred nanometers in diameter, calculations from EM images predict a potential increase in binding capacity to nearly 100 g/L. The accessible volume for adenovirus calculated from the EM images matched the experimental value. While the pores of perfusive resins are essentially inaccessible to adenovirus under binding conditions, under non-adsorbing conditions the accessible intrabead porosity is almost as large as the interbead porosity. Modeling of breakthrough curves showed that the experimentally observed slow approach to full saturation can be explained by the distribution of pore sizes.     

Structural and optical properties of GaN thin films grown on Al2O3 substrates by MOCVD at different reactor pressures

GaN thin films grown by MOCVD on (0 0 0 1) Al₂O₃ substrates at different growth pressures were characterized by field-emission scanning electron microscopy, atomic force microscopy, micro-Raman, and photoluminescence at room temperature. It was found that there is an optimum pressure of 76 Torr at which the structural and optical properties of the GaN samples are superior. On the other hand samples grown at higher pressure exhibited hexagonal surface pits and surface spirals. The results showed that the growth pressure strongly influences the morphology, and significantly affects the structural and optical properties of the GaN epilayers.     

Electrospun ceramic fibers: Composition, structure and the fate of precursors

Fibers are electrospun from aluminum acetate/polymer mixtures and characterized by an array of techniques before and after annealing at 1200 °C. We demonstrate that sodium and boron present in the initial starting materials as adducts and stabilizers remain incorporated into the resulting fibers after annealing and pyrolysis of the host polymer. The influence of these minor constituents on the surfaces of the fibers is suggested by infrared and X-ray photoelectron spectroscopic data. The presence of these species may impact potential chemical applications of small diameter ceramic fibers, such as their use as catalytic supports or for chemical decomposition.     

Synthesis of cubic ZrWMoO8 by a melt quenching method

We report a novel approach for fabrication of cubic ZrWMoO₈ applying a melt quenching method. The stoichiometric mixture of ZrO₂, WO₃ and MoO₃ in a 1:1:1 M ratio was melted and quenched at room temperature by pouring the melts between two metal plates. The quenched sample was characterized by X-ray diffraction (XRD), differential thermal analysis (DTA) and scanning electron microscopy (SEM) analysis. As quenched material is polyphase contains above 70% ZrWMoO₈. The obtained composite is thermal stable up to 930 °C. The ZrWMoO₈ was indexed as cubic with a lattice parameter a = 9.1263 (3) Å calculated by the “PowderCell” program. By SEM observation it was established that the microstructure of bulk composite material is built up of one-direction orientated agglomerates with cuboid crystal morphology.     

Adsorption of water on JSC‐1A (simulated moon dust samples)—a surface science study

JSC‐1a (a simulated lunar dust sample) supported on a silica wafer (SiO₂/Si(111)) has been characterized by scanning electron microscopy (SEM), energy dispersive x‐ray (EDX) spectroscopy, and Auger electron spectroscopy (AES). The adsorption kinetics of water has been studied primarily by thermal desorption spectroscopy (TDS) and in addition by collecting isothermal adsorption transients. Blind experiments on the silica support have been performed as well. JSC‐1a consists mostly of aluminosilicate glass and other minerals containing Fe, Na, Ca, and Mg, as characterized in detail in prior studies, for example, at NASA. The particle sizes span the range from a few micrometers up to 100 µm. At small exposures, H₂O TDS is characterized by broad (100–450) K structures; at large exposures, distinct TDS peaks emerge, which are assigned to amorphous solid water (ASW) (145 K) and crystalline ice (CI) (165 K). Water dissociates on JSC‐1a at small exposures but not on the bare silica support. Coadsorption TDS data (alkane–water mixtures) indicate that rather porous condensed ice layers form at large exposures, with the mineral particles acting most likely as nucleation sites. At thermal impact energies, the initial adsorption probability amounts to 0.92 ± 0.05. It is evident that the drop‐and‐dry technique, developed in studies about nanoparticles/tubes, can be extended to obtain samples for surface science studies based on powders consisting of particles with rather large diameters. Copyright © 2008 John Wiley & Sons, Ltd.     

Preparation and applications of novel fluoroalkyl end‐capped vinyltrimethoxysilane oligomer/hydroxyapatite nanocomposites

Novel fluoroalkyl end‐capped vinyltrimethoxysilane oligomer/hydroxyapatite (HAp) nanocomposites were prepared by the reaction of calcium nitrate tetrahydrate and phosphoric acid in the presence of the corresponding oligomer. These fluorinated oligomer/HAp composites thus obtained are nanometer size‐controlled fine particles (83–173 nm), and were found to exhibit good dispersibility in methanol, ethanol, and isopropyl alcohol. These fluorinated HAp nanocomposites were applied to the surface modification of glass and poly(methyl methacrylate) (PMMA) to exhibit good hydro‐ and oleophobic characteristics imparted by fluorine on their surface. In addition, the surface structural changes of the modified polyethylene terephtalate and PMMA films treated with these fluorinated nanocomposites before and after soaking in a simulated body fluid (SBF) were analyzed by using SEM, XRD, and EDX to observe the formation of spherical HAp deposits on the surface. Copyright © 2009 John Wiley & Sons, Ltd.     

Archaeometrical study of paleometallurgical materials from the archaeological site “Cerro de las Balsas — Chinchorro” (La Albufereta, Alacant, Spain)

An Iberian archaeological site located in the east of Spain is one of the most important cupellation centers found in the 4th century b.c. Different metallurgical materials were found in the archaeological site as minerals, cast slags, forged slags, metallic lead, cupella fragments and bronzes. Also was found reverbs remains used for cupper-based materials and cupellation procedure, and hearth forge remains for obtained iron material. The recuperated samples were studied by comparing samples of the same type of material by macroanalysis and microanalysis. The microanalysis and quantitation of the different archaeological materials was carried out by SEM/EDX. The information provides about the knowledge of a metallurgic process such as that of silver production by lead cupellation. The microanalysis results reflect the variety of elements that constitute the slags and other materials, and that come from the forge of the worked metallic materials. Also, the process cupellation was confirmed by the identification of lead and silver. The presence of forge slag corroborates the use of the great amount of recovered heart forges in the excavation like metallurgical structures for the iron work.     

Toxic effect of triphenyltin chloride on the alga Spirulina subsalsa

A previous study on the deleterious effect of triphenyltin chloride (TPTCl) on the alga Spirulina subsalsa reported on four physiological and biochemical indices (or parameters): growth rate, chlorophyll content, phycocyanin content and nitrate reductase activity. In the present study, further research was performed to confirm the findings reported in the previous paper, using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The SEM images show significant changes in the screw‐pitch of S. subsalsa, suggesting that TPTCl may damage the inheritance characteristics of S. subsalsa. The TEM images illustrate that the external pectin theca, limiting membrane and inter photosynthetically active lamella in the S. subsalsa cell are those targets that can be easily damaged. Reversible and irreversible cell damage (cell necrosis) are also observed. Copyright © 2002 John Wiley & Sons, Ltd.     

三门峡虢季墓遗址盐害分析与调查

针对三门峡虢季墓遗址部分区域存在起甲、泛白、疱疹等由可溶盐引起的病害,在其遗址不同部位取样进行土遗址本体含盐分析.取样区域包括虢季墓、梁姬墓和近代墓遗址.采用X射线荧光光谱(XRF)和离子色谱(IC)分析所取样品的可溶盐成分、含量及可溶盐成盐元素在土遗址中的成盐规律.采用电子能谱(XPS)和X射线衍射(XRD)分析样品的物相组成及盐分状态,扫描电子显微镜/能谱(SEM/EDS)进一步考察含盐土质的颗粒组成、微观形貌等.结果表明:虢季墓取样区域所含盐分主要为Na_2SO_4、CaCO_3和少量的其他盐分如CaCl_2、KNO_3和NaCl等.靠近地面部位所取样品盐分含量高于其他部位,盐害表现更为明显.梁姬墓取样区域总盐分含量略高于虢季墓与近代墓,硝酸盐含量较高.而近代墓遗址可溶盐盐分含量略低,盐害不明显.在不同取样点可溶盐含量有所差异,但在邻近区域,其成盐具有一定规律性,这一点对于遗址基体中盐害的深入研究与防治具有重要意义.