Back propagation modeling of shear stress and viscosity of aqueous Ionic-MXene nanofluids

Journal of Thermal Analysis and Calorimetry - Back-propagation modeling of viscosity and shear stress of Ionic-MXene nanofluid is carried out in this work. The data for Ionic-MXene nanofluid of...     

Box–Behnken Design (BBD)-Based Optimization of Microwave-Assisted Extraction of Parthenolide from the Stems of Tarconanthus camphoratus and Cytotoxic Analysis

Parthenolide, a strong cytotoxic compound found in different parts of Tarchonanthus camphoratus which motivated the authors to develop an optimized microwave-assisted extraction (MEA) method using Box–Behnken design (BBD) for efficient extraction of parthenolide from the stem of T. camphoratus and its validation by high-performance thin-layer chromatography (HPTLC) and cytotoxic analysis. The optimized parameters for microwave extraction were determined as: 51.5 °C extraction temperature, 50.8 min extraction time, and 211 W microwave power. A quadratic polynomial model was found the most suitable model with R² of 0.9989 and coefficient of variation (CV) of 0.2898%. The high values of adjusted R² (0.9974), predicted R² (0.9945), and signal-to-noise ratio (74.23) indicated a good correlation and adequate signal, respectively. HPTLC analyzed the parthenolide (R_f = 0.16) content in T. camphoratus methanol extract (TCME) at λ_max = 575 nm and found it as 0.9273% ± 0.0487% w/w, which was a higher than expected yield (0.9157% w/w). The TCME exhibited good cytotoxicity against HepG2 and MCF-7 cell lines (IC₅₀ = 30.87 and 35.41 µg/mL, respectively), which further supported our findings of high parthenolide content in TCME. This optimized MAE method can be further applied to efficiently extract parthenolide from marketed herbal supplements containing different Tarconanthus species.     

Kinetics of pyrolysis of sugarcane bagasse: effect of catalyst on activation energy and yield of pyrolysis products

Cellulose - In this work we have attempted to use biomass as energy source which is abundantly available throughout the world. The work is focused on pyrolysis of sugarcane bagasse in a...     

A general strategy for selective detection of hypochlorous acid based on triazolopyridine formation

Triazolopyridines are an important kind of fused-ring compounds. A HOCl-promoted triazolopyridine formation strategy is reported here for the first time in which hypochlorous acid (HOCl) mildly and efficiently promotes the formation of 1,2,4-triazolo[4,3-a]pyridines NT1-NT6 from various 2-pyridylhydrazones N1-N6. N6, a rhodol-pyridylhydrazone hybrid, was developed into a fluorescent probe for the selective detection of HOCl, and successfully applied to probe endogenous HOCl in living cells and zebrafish in situ and in real time. The present intramolecular cyclization reaction is selective and atom-economical, thereby not only providing an important approach for the convenient synthesis of triazolopyridines, but also offering a general strategy for sensitive, selective and biocompatible detection of endogenous HOCl in complex biosystems.     

Developing imprinted polymer nanoparticles for the selective separation of antidiabetic drugs

In this study, new molecularly imprinted polymer (MIP) nanoparticles are designed for selective recognition of different drugs used for the treatment of type 2 diabetes mellitus, i.e. sitagliptin (SG) and metformin (MF). The SG‐ and MF‐imprinted polymer nanoparticles are synthesized by free‐radical initiated polymerization of the functional monomers: methacrylic acid and methyl methacrylate; and the crosslinker: ethylene glycol dimethacrylate. The surface morphology of resultant MIP nanoparticles is studied by atomic force microscopy. Fourier transform infrared spectra of MIP nanoparticles suggest the presence of reversible, non‐covalent interactions between the template and the polymer. The effect of pH on the rebinding of antidiabetic drugs with SG‐ and MF‐imprinted polymers is investigated to determine the optimal experimental conditions. The molecular recognition characteristics of SG‐ and MF‐imprinted polymers for the respective drug targets are determined at low concentrations of SG (50–150 ppm) and MF (5–100 ppm). In both cases, the MIP nanoparticles exhibit higher binding response compared to non‐imprinted polymers. Furthermore, the MIPs demonstrate high selectivity with four fold higher responses toward imprinted drugs targets, respectively. Recycled MIP nanoparticles retain 90% of their drug‐binding efficiency, which makes them suitable for successive analyses with significantly preserved recognition features.     

Phase transformation studies in unirradiated and proton beam irradiated Ni–Ti alloy between 25 and 100°C

The stress-induced phase transformation characteristics of unirradiated and proton beam irradiated NiTi alloy were investigated at different tests temperatures. The wire-shaped NiTi specimens were irradiated by 2?MeV proton beam for 30?min at room temperature to a flux of 10¹⁹ protons/m² s. Engineering stress–strain (S-S) curves of both unirradiated and irradiated specimens were obtained using a materials testing machine at 25, 50, 75 and 100°C. The results indicate a single-stage phase transformation from austenite to martensite (B2–B19′) in unirraidated specimens at all the test temperatures. In contrast, in the case of the irradiated specimens, a two-stage austenite–rhombohedral–martensite (B2–R–B19′) phase transformation is observed at 25 and 50°C. The B2–R–B19′ phase transformation, however, is found to change into B2–B19′ transformation at 75 and 100°C. The stress required to initiate the B19′ phase transformation (σ_MS) and the plateau range are found to be lower in irradiated specimens compared with those of the unirradiated specimens. The results obtained are discussed on the basis of the formation of Ni₄Ti₃ precipitates in irradiated specimens and their consequences on the phase transformations.     

New Supramolecular Triorganotin(IV) Dithiocarboxylates as Potential Antibacterial Agents

Four triorganotin derivatives of general formula C₁₀H₁₀NS₂SnR₃,_, where R = CH₃ ( 1 ), C₄H₉ ( 2 ), C₆H₁₁ ( 3 ), and C₆H₅ ( 4 ), have been synthesized by the metathesis reaction of 1,2,3,4‐tetrahydroisoquinolnium salt of ligand with triorganotin(IV) chloride in the 1:1 ratio. These complexes were characterized by elemental analysis, Raman, IR, multinuclear NMR (¹H, ¹³C, and ¹¹⁹Sn), and mass spectrometry. The crystal structure confirmed a supramolecular zig‐zag chain structure mediated by S–H (2.968 Å) for complex 4 with the central Sn atom exists in a distorted trigonal bipyramidal geometry. A subsequent antibacterial study indicates that the compounds are biologically active.     

DNA binding and cleavage studies of new sulfasalazine-derived dipeptide Zn(II) complex: Validation for specific recognition with 5′–TMP

Synthesis, characterization, DNA binding and cleavage studies of [Zn(glygly)(ssz)(H₂O)]·6H₂O (1) containing glycyl glycine and sulfasalazine ligand. Complex 1 recognize minor groove of DNA and show hydrolytic DNA cleavage.

1. Download : Download high-res image (215KB)
2. Download : Download full-size image

Highlights? Novel Zn(II) complex 1 bearing bioactive glycyl glycine and sulfasalazine ligand scaffold. ? Cleavage activity of 1 was enhanced in presence of activators: H₂O₂>MPA>GSH>Asc. ? Complex 1 recognize minor groove as depicted in the cleavage pattern and molecular docking. ? Complex 1 cleaves pBR322 DNA via hydrolytic mechanism and validated by T4 DNA ligase experiments.     

Recognizing triangulated Cartesian graph products

Computational meshes for numerical simulation frequently show—at least locally—a structure resembling a triangulated grid. Our goal is to recognize product-like structures in triangular meshes. We define triangulated Cartesian products of graphs and analyze their structural properties. We show how to recognize and factorize graphs that are triangulated products of two factors, when the factors are triangle-free graphs. We also discuss properties of products with more than two factors.     

A coupled WC-TL SPH method for simulation of hydroelastic problems

A coupled weakly compressible (WC) and total Lagrangian (TL) smoothed particle hydrodynamics (SPH) method is developed for simulating hydroelastic problems. The fluid phase is simulated using WCSPH method, while the structural dynamics are solved using TLSPH method. Fluid and solid components of the method are validated separately. A sloshing water tank problem is solved to test the WCSPH method while oscillation of a thin plate and large deformation of a cantilever beam are simulated to test the TLSPH method. After validating each component, the coupled WC-TL SPH scheme is used to simulate two benchmark hydroelastic problems. The first test case shows the evolution of water column with an elastic boundary gate, and the second one investigates the breaking water column impact on elastic structures. The agreement between WC-TL SPH results and literature data shows the ability of the proposed method in simulating hydroelastic phenomena.