Quantitative evaluation of stress distribution in bulk polymer samples through the comparison of mechanical behaviors between giant single‐crystal and semicrystalline samples of poly(trans‐1,4‐diethyl muconate)

The Raman shift and crystallite modulus were measured under the application of tensile force for a giant single crystal and a series of uniaxially oriented semicrystalline samples of poly(trans‐1,4‐diethyl muconate) (polyEMU). The apparent Raman shift factor α^app or a vibrational frequency shift per 1 GPa tensile stress was higher for the semicrystalline samples with lower crystallinity or lower bulk modulus. The apparent crystallite modulus E or Young's modulus along the chain axis in the crystalline region was not constant but varied remarkably between the giant single crystal and semicrystalline samples. A systematic change in α^app and E among the polyEMU samples with different preparation history could be interpreted quantitatively on the basis of a mechanical series parallel model consisting of crystalline and amorphous phases. The origin of different E and α^app was speculated to be a stress concentration on the taut‐tie chain contained as a parallel crystalline component in the mechanical model. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 444–453, 2003     

In situ real-time study buckling behavior of boron nitride nanotubes with axial compression by TEM

The real time analysis structure evolution of BNNT with compression showed that the formation of V-shape in the post-buckling before BNNT fracture was reversible.     

STUDY ON THE PROPERTIES OF BLEND OF NATURAL RUBBER LATEX/METHYL METHACRYLATE GRAFTED RUBBER LATEX BY GAMMA RADIATION

Natural rubber latex(NRL)and methyl methacrylate(MMA)grafted rubber latex were blended in different ratios and irradiated at various absorbed doses by gamma rays from Co-60 source at room temperature.The tensile properties, swelling ratio and permanent set were measured.The maximum tensile strength and modulus at 500% elongation were obtained at an absorbed dose of 8 kGy.Modulus increases from 6.99 MPa to 9.87 MPa for an increase in proportion of MMA grafted rubber from 40% to 60% in the blend at similar absorbed dose.Elongation at break and swelling ratio decrease with increasing absorbed dose as well as the MMA grafted rubber content in the blends.The decreasing trend of permanent set is high up to 5 kGy absorbed dose,and beyond that dose,it becomes almost flat.     

General analysis of the measurements of the lateral crystal lattice moduli of semicrystalline polymers by x-ray diffraction and the application to nylon 6

A mathematical representation based on a linear elastic theory is proposed by which one may investigate the dependences of molecular orientation and crystallinity on the crystal lattice moduli and linear thermal expansion coefficients in the direction perpendicular to the chain axis as commonly measured by x-ray diffraction. In the theoretical calculation, a previously introduced model was employed in which oriented crystalline phase is surrounded by oriented amorphous phase and the strains of the two phases at the boundary are identical. The mathematical analysis indicated that the lateral crystal lattice moduli and linear thermal coefficients as measured by x-ray diffraction may be different from the intrinsic crystal moduli and linear thermal coefficients of a crystal unit cell, depending on the structure of the polymer solid. The numerical calculation was applied to nylon 6. As a result, it may be confirmed that the lateral crystal lattice moduli measured by x-ray diffraction are sensitive to the morphology of the bulk speciments and close to the intrinsic crystal moduli if the morphology of the test specimen can be represented by a parallel model with respect to the original stretching longitudinal direction.     

Swelling behavior and mechanical properties of endlinked poly (dimethylsiloxane) networks and randomly crosslinked polyisoprene networks

Measurements of the equilibrium degree of swelling and of the equilibrium modulus were performed on poly(dimethylsiloxane) networks (PDMS) and on polyisoprene vulcanizates. The results support the concept that topological interactions between network chains, e.g. entanglements or the like, have a large influence on the rubber elastic behavior, at least within a certain range of network densities.PDMS networks having network chains of different lengths and varying functionlities of the crosslinks were prepared in bulk by endlinking fractionated ,-divinyl PDMS via multifunctional hydrogen-siloxanes (f=3 to 22). Natural rubber (NR) and synthetic liquid polyisoprene (IR) were cured in bulk with various amounts of dicumyl peroxide to give randomly crosslinked samples.The experimentally determined moduli and degrees of swelling were compared with theoretical predictions based on the phantom network theory and affine network theory, taking into account only chemical crosslinks. The observed discrepancies can be traced back to a contribution of topological interactions (trapped entanglements) to the total effective network density. The modulus and swelling data are consistent, thus ruling out non-equilibrium effects.     

Influence of high pressure treatment on rheological and other properties of egg white

Abstract

The paper deals with the influence of high pressure treatment of fresh egg white on its properties and protein composition (individual amino-acids predicted as a function of pressure and time levels). The rheological properties are changed by high pressure from Newtonian to non-Newtonian behaviour, with increasing apparent viscosity as the pressure and time increased. The pH, whipping ability, foam stability, gel strength of heat induced gels after treatment and the whole protein content, were also predicted.

The results showed that the foam stability is increased with increasing pressure and time of processing. The foam volume is also increased with pressure. The pH did not change with pressure or time of processing. Composition of proteins as indicated by individual amino-acids did not exhibit statistically important changes. Gel strength of heat induced gels prepared from previously pressured liquid whites showed no important change of values with pressure or time of treatment. The modulus of elasticity showed a decrease for samples pressured to 400 MPa for 5 up to 15 minutes.     

Study of Temperature and UV Wavelength Range Effects on Degradation of Photo-Irradiated Polyethylene Films Using DMA

Plastic bags mostly made of polyethylene (PE) cause pollution as solid waste due to their non-degradability nature. Initiation of a degradative process by enhanced photo-oxidation is a possible method for an accelerated degradation. This paper presents temperature treatment effects on PE films where photodegradation was initiated using ultraviolet (UV) irradiation in the ranges of 200–300 nm and 300–400 nm for 2 hr. Effects of temperature of 40°C and 55°C on non-UV-irradiated and UV-irradiated PE films processed by conventional methods were investigated and evaluated after 50 hr, 150 hr, and 350 hr of temperature exposure. The effects of UV wavelength range irradiation on the degradation were deduced. Measuring the dynamic moduli using a dynamic mechanical analyzer monitored the degradation. The decrease in average storage modulus was 62% with treatment at 55°C, higher than the 16% drop at 40°C for unirradiated samples after 350-hr exposure. Cross-linking in UV-exposed samples, characterized by an increase in dynamic modulus (stiffening), was observed followed by a reduction of storage modulus. Temperature treatment at 55°C together with 300–400-nm UV range irradiation resulted in the largest increase, i.e., 22% after 150 hr, followed by the largest reduction of storage modulus, i.e., 74.6% for a cumulative 350-hr exposure.     

Wrinkle morphologies with two distinct wavelengths

Wrinkles with two distinct wavelengths formed sequentially on the same surface are investigated. A series of aligned wrinkles are formed through local strain application on a partially crosslinked elastomer. After the formation of these primary wrinkles, the elastomer is fully crosslinked, and a mechanical compressive strain is applied to the sample orthogonal to the primary wrinkles. This mechanical strain results in smaller secondary wrinkles superimposed on the larger primary aligned wrinkles. Resulting biaxial morphologies suggest that the primary pattern directs the formation of the smaller wrinkles. The modulus mismatch of the substrate on primary and secondary wrinkle formation dictates the ratio between the two resulting wavelengths, as well as the specific biaxial morphologies, ranging from zigzag ridges to ellipsoidal bumps or corn‐on‐the‐cob structures to the classic herringbone. The sequential strain wrinkling process has the potential to be used on an industrial scale for the facile formation of surface topography with two discrete, tunable lateral dimensions over large surface areas. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Preparation and Characterization of Isotactic Polypropylene Reinforced with Hydroxyapatite Nanorods

Isotactic polypropylene (PP) composites filled with hydroxyapatite nanorods (nHAs) were fabricated using a melt compounding process. The effects of nHA additions on the structure, thermal, and mechanical properties as well as bioactivity of PP were investigated. Wide-angle X-ray diffraction and differential scanning calorimetry results showed that PP crystallized exclusively in the α-form when adding nHAs. Dynamic mechanical analysis showed that nHAs enhanced the storage modulus of PP. Mechanical measurements showed that nHAs stiffened and reinforced PP but reduced its tensile ductility and impact strength considerably. Furthermore, the PP/nHA nanocomposites were found to exhibit excellent bioactivity upon immersion in a simulated body fluid solution. This was attributed to the formation of apatite mineral crystals on the nanocomposite surfaces as revealed by scanning electron microscopy and energy dispersive X-ray analysis.     

Electrical Impedance Spectroscopic Study of CNT/Ethylene-alt-CO/Propylene-alt-CO Polyketones Nanocomposite

Impedance spectroscopy was utilized to investigate the dielectric properties, ac conductivity and charge transport mechanisms in propylene-alt-CO/ethylene-alt-CO (EPEC) random terpolymer filled with multi-walled carbon nanotubes (MWCNT) as a function of nanofiller content, frequency, and temperature. Equivalent resistor-capacitor (RC) circuit models were proposed to describe the impedance characteristics of the unfilled terpolymer and the nanocomposite at different temperatures. For the nanocomposites, the ac conductivity tended to be frequency independent at low frequencies. At high frequencies, the ac conductivity increased with frequency. The dc conductivity (i.e., plateau of the ac conductivity at low frequencies) at room temperature increased from 10^?9 (Ω·m)^?1 for the unfilled polymer to l0^?3 (Ω·m)^?1 for the 6 wt% MWCNT/EPEC nanocomposite. At low temperatures, the equivalent RC model for EPEC-0 and EPEC-2 was found to consist of a parallel RC circuit. However, for 6 wt% MWCNT/EPEC nanocomposite, an RC model consisting of an R/constant phase element (CPE) circuit and a resistor in series was required to describe the impedance behavior of the nanocomposite.