Discrete vs. continuum-scale simulation of radiative transfer in semitransparent two-phase media

The mathematical formulation of the continuum approach to radiative transfer modeling in two-phase semi-transparent media is numerically validated by comparing radiative fluxes computed by (i) direct, discrete-scale and (ii) continuum-scale approaches. The analysis is based on geometrical optics. The discrete-scale approach uses the Monte Carlo ray-tracing applied directly to real 3D geometry measured by computed tomography. The continuum-scale approach is based on a set of continuum-scale radiative transfer equations and associated radiative properties, and employs the Monte Carlo ray-tracing for computations of radiative fluxes and for computations of the radiative properties. The model two-phase media are reticulate porous ceramics and a particle packed bed, each composed of semitransparent solid and fluid phases. The results obtained by the two approaches are in good agreement within the limits of statistical uncertainty. The continuum-scale approach leads to a reduction in computational time by approximately one order of magnitude, and is therefore suited to treat radiative transfer problems in two-phase media in a wide range of engineering applications.     

Propagation characteristics of annular laser beams passing through the reflection Bragg grating with deformation

When high-power annular laser beams produced by the unstable resonator pass through the volume Bragg grating (VBG), absorption of light in the VBG will induce a temperature increment, resulting in changes in surface distortion. Considering that the surface distortion of the grating induces index and period differences, the scalar wave equations for the annular laser beams propagating in the VBG have been solved numerically and iteratively using finite-difference and sparse matrix methods. The variation in intensity distributions, the total power reflection coefficient, and the power in the bucket (PIB) for the annular laser beams passing through the reflection VBG with deformation have been analyzed quantitatively. It can be shown that the surface distortion of the VBG and the beam orders of the annular beams affect evidently the intensity distributions, the power reflection coefficient, and the PIB of the output beam. The peak intensity decreases as the deformation of the VBG increases. The total power reflection efficiency decreases significantly with the increase in deformations of the VBG. The PIB of the output beam decreases as the obscuration ratio β and the deformation of the VBG increase. For the given obscuration ratio β, the influence of deformation of reflection VBG on the PIB of the annular beams is more sensitive with increase in distortion of the VBG and decrease in beam order.     

Differentiation between intra-axial metastatic tumor progression and radiation injury following fractionated radiation therapy or stereotactic radiosurgery using MR spectroscopy, perfusion MR imaging or volume progression modeling

Objective

To determine the accuracy of magnetic resonance spectroscopy (MRS), perfusion MR imaging (MRP), or volume modeling in distinguishing tumor progression from radiation injury following radiotherapy for brain metastasis.

Methods

Twenty-six patients with 33 intra-axial metastatic lesions who underwent MRS (n=41) with or without MRP (n=32) after cranial irradiation were retrospectively studied. The final diagnosis was based on histopathology (n=4) or magnetic resonance imaging (MRI) follow-up with clinical correlation (n=29). Cho/Cr (choline/creatinine), Cho/NAA (choline/N-acetylaspartate), Cho/nCho (choline/contralateral normal brain choline) ratios were retrospectively calculated for the multi-voxel MRS. Relative cerebral blood volume (rCBV), relative peak height (rPH) and percentage of signal-intensity recovery (PSR) were also retrospectively derived for the MRPs. Tumor volumes were determined using manual segmentation method and analyzed using different volume progression modeling. Different ratios or models were tested and plotted on the receiver operating characteristic curve (ROC), with their performances quantified as area under the ROC curve (AUC). MRI follow-up time was calculated from the date of initial radiotherapy until the last MRI or the last MRI before surgical diagnosis.

Results

Median MRI follow-up was 16 months (range: 2-33). Thirty percent of lesions (n=10) were determined to be radiation injury; 70% (n=23) were determined to be tumor progression. For the MRS, Cho/nCho had the best performance (AUC of 0.612), and Cho/nCho >1.2 had 33% sensitivity and 100% specificity in predicting tumor progression. For the MRP, rCBV had the best performance (AUC of 0.802), and rCBV >2 had 56% sensitivity and 100% specificity. The best volume model was percent increase (AUC of 0.891); 65% tumor volume increase had 100% sensitivity and 80% specificity.

Conclusion

Cho/nCho of MRS, rCBV of MRP, and percent increase of MRI volume modeling provide the best discrimination of intra-axial metastatic tumor progression from radiation injury for their respective modalities. Cho/nCho and rCBV appear to have high specificities but low sensitivities. In contrast, percent volume increase of 65% can be a highly sensitive and moderately specific predictor for tumor progression after radiotherapy. Future incorporation of 65% volume increase as a pretest selection criterion may compensate for the low sensitivities of MRS and MRP.     

Improvement of the dynamic range of a fiber specklegram sensor based on volume speckle recording in photorefractive materials

In this work, the improvement of the dynamic range of a micro displacement sensor based on fiber specklegrams holographically stored in a photorefractive BSO (Bi₁₂SiO₂₀) crystal is reported. In our experimental setup, a plastic optical fiber (POF) was used to generate a subjective speckle pattern that was recorded in the crystal using a two-wave mixing arrangement. The speckle size was controlled by modifying the diameter of a pupil aperture adjacent to a lens producing the image of the speckle. Fringe patterns were obtained at the output of the system by producing micro displacements of the fiber output end. An increase in the visibility of the fringe patterns was appreciated when the pupil aperture diameter decreased even without controlling the average modulation of the intensity of the light pattern, i.e. when the speckle length increased and the average light modulation simultaneously decreased. This behavior allowed recovering the autocorrelation functions of fringe patterns associated with displacements that initially led to decorrelation, and therefore, significantly to improve the dynamic range of the metrological system. To the best of our knowledge this is the first report about the influence of speckle size on the dynamic range of fiber specklegrams sensors recorded on photorefractive materials.     

体积相位全息光栅的设计与制备

本文指出全息干版薄膜在曝光后处理过程中的收缩性和折射率变化对制备全息光栅的周期、倾斜度、布喇格入射角及衍射角的影响问题,并根据实验数据对光栅设计进行修正,再结合Kogelnik衍射方程及折射率调制度和曝光量的线性关系,在实验中基本上能准确设计出指定周期、倾斜度和衍射效率的全息光栅。     

4维完备Einstein流形的一些注释

本文给出了在开的定向的4维流形上存在有界曲率的完备Einstein度量的障碍．     

联系两个n维单形的一类不等式

本文给出了联系两个ｎ维单形的一类不等式，从而推广和改进了文［１］、［２］［３］的结论。     

空腔靶X光发射特性研究

在“神光”装置上对几种类型的空腔靶进行了激光打靶实验,我们利用亚千X光透射光栅谱仪(TGS)、针孔相机(PC)、以及平响应X光二极管(P-XRD)对激光等离子体X光发射特性进行了研究。基本上弄清了空腔靶源区、向爆区X光发射特性。为激光间接驱动内爆的理论数值模拟和靶的优化设计提供了实验依据。     

Modeling of metallic foam morphology using the Representative Volume Element approach: Development and experimental validation

This paper focuses on the development of an algorithm capable of generating morphologically-representative foam structures using the Representative Volume Element (RVE) approach. Stereology, a sampling method based on direct observations of the foam cross-sections, is used to characterize the pore size and shape distributions. Using the morphology generation algorithm, the smallest RVEs corresponding to the numerically-convergent foam morphologies are calculated for different foam porosities. To validate the foam generation algorithm, the pore size and shape distributions of the numerically-generated foams are compared to those of the titanium foams manufactured by the space holder method.