翼型模型振动的实验研究与气动特性分析

通过在NF-3低速风洞专门研制的翼型模型及相应的俯仰和沉浮振动机构,选用NACA0012翼型进行大迎角下不同频率的振动实验,研究了模型振动平均状态下对其气动力特性的影响情况,并在N-S方程基础上对振动流场进行了初步分析。实验与计算研究的结果表明:在临近定常失速迎角的大迎角条件下,翼型的振动可以引起旋涡分离,导致翼型升力减小和失速迎角的提前;就所讨论的两种振动模式而言,俯仰振动的影响大于沉浮振动。所以,为了提高飞机模型,尤其是大展弦比飞机模型的风洞实验精准度,在模型设计和加工时要特别注意加强机翼弦向的扭转刚度。     

Note on the critical variational state in elasticity theory

Recently Prof. Chien Wei-zang pointed out that in certain cases, by means of ordinary Lagrange multiplier method, some of undetermined Lagrange multipliers may turn out to be zero during variation. This is a critical state of variation. In this critical state, the corresponding variational constraint can not be eliminated by means of simple Lagrange multiplier method. This is indeed the case when one tries to eliminate the constraint condition of strain-stress relation in variational principle of minimum complementary energy by the method of Lagrange multiplier.By means of Lagrange multiplier method, one can only derive, from minimum complementary energy principle, the Hellinger-Reissner Principle, in which only two type of in-dependent variables, stresses and displacements, exist in the new functional. Hence Prof. Chien introduced the high-order Lagrang multiplier method bu adding the quadratic terms.to original functions. The purpose of this paper is to show that by adding to original functionals one     

Modeling three-dimensional dynamic stall

The dynamic stall process in three-dimensional (3D) cases on a rectangular wing undergoing a constant rate ramp-up motion is introduced to provide a qualitative analysis about the onset and development of the stall phenomenon. Based on the enhanced understanding of the mechanism of dynamic stalls, a 3D dynamic stall model is constructed with the emphasis of the onset, the growth, and the convection of the dynamic stall vortex on the 3D wing surface. The results show that this engineering dynamic stall model can simulate the 3D unsteady aerodynamic performance appropriately.     

Dynamic stall modelling on airfoils based on strong viscous–inviscid interaction coupling

The prediction of the aerodynamic performance of pitching airfoils in stall conditions is considered in the context of strong viscous–inviscid interaction modelling. The aim of the work is to demonstrate the capabilities of a low‐cost dynamic stall model well suited for engineering applications. The model is formulated on the basis of a standard panel method combined with a vortex blob approximation of the wake. The development of the boundary layer over the airfoil and the evolution of the shear layer in the wake are taken into account by means of strong viscous–inviscid interaction coupling. To this end a transpiration layer is added to the inviscid formulation which represents the displacement effect viscosity results in the flow while the non‐linear coupled equations are solved simultaneously. Separation is modelled by introducing a second wake originating from the separation point (‘double‐wake’ concept) which is provided as part of the boundary layer solution. The theoretical presentation of the model is supported with favourable comparisons to four sets of wind tunnel measurements. Copyright © 2007 John Wiley & Sons, Ltd.     

掠效应对高负荷跨音转子性能的影响

本文对一高负荷跨音转子采用掠技术进行了改型设计,并通过数值模拟对原型以及前、后掠转子分别进行了流场分析。结果发现掠叶片效率和压比与原型叶片相差不大,但是前掠叶型的失速裕度得到了大幅提高。同时前掠叶型的堵塞流量比原始叶型增大,而后掠叶型却明显减小。叶片采用掠之后一方面前缘位置变化所引起的径向压力输运改变了入口来流条件,另一方面气动掠还直接影响到了叶片吸力面附面层内低能流体的径向输运以及在叶尖区域的集聚,从而使流场内部的激波强度及相对位置明显变化,并最终导致叶片不同叶高载荷分布规律的改变。     

环形腔处理机匣对低速风扇性能和失速裕度的影响

本文从实验角度探讨一种新型带有环形腔的槽式处理机匣对风扇性能和失速裕度的影响。结果表明:处理机匣的槽向和槽与转子轴向重合度是影响风扇性能的两个主要参数,应用于本实验的低速风扇中,圆弧槽槽向与转子叶型方向相错,槽与转子轴向重合度为1/3的环形腔处理机匣对风扇失速裕度有明显提高,但效率略有下降。同时随环形腔腔体体积增大风扇裕度有明显振荡变化,进一步的规律值得深入探讨。     

Active feedback control of stall in an axial flow fan under dynamic inflow distortion

This work proposes an active feedback control strategy using cross-correlation technique in a single stage axial flow fan operating under dynamic inflow distortion. Experiments were carried out under dynamic inflow distortion at the design speed with only three sensors and actuators, each. The stall inception mechanism studies under dynamic inflow distortion were carried out using 1-D continuous Morlet wavelet transform. It was observed that stall inception under co- (in the same direction of rotor rotation) and counter-rotating (in the opposite direction of rotor rotation) inflow distortion occurred through long and short length-scale disturbances, respectively. The knowledge of the nature of instabilities under dynamic inflow distortion was used to set the threshold of the correlation coefficient. It was observed that the active feedback control strategy resulted in a stall onset delay of 125 (?3.125 s) and 65 (?1.625 s) rotor revolutions under co- and counter-rotating inflow distortions, respectively. The highest delay under co-rotating inflow distortion was attributed to the substantially higher stall warning time as compared to counter-rotating inflow distortion.     

涡轮增压器离心压气机非稳态工况流场分析

利用商用 CFD 软件对一小型车用离心压气机建立了数值模型,并将模拟结果与实验结果进行了对比:稳态的设计转速最高压比相差不超过 0.5%,最高效率相差不超过1.5%;非稳态模拟和实验得到的失速频率均为 3000Hz,模拟结果真实可信.主要利用设计转速下小流量工况时的非稳态数值模拟结果对喘振发生前离心压气机各部件的非稳态流动特点进行了详尽阐述.研究结果表明:小流量工况时离心压气机各部件均出现非稳态流动现象,这种非稳态效应在各部件中表现出不同的特点,且随着流量的减小这种非稳态效应会不断加剧.     

Assessment of 2D/3D numerical modeling for deep dynamic stall experiments

The results of computational fluid dynamics (CFD) simulations in two and three spatial dimensions are compared to pressure measurements and particle image velocimetry (PIV) flow surveys to assess the suitability of numerical models for the simulation of deep dynamic stall experiments carried out on a pitching NACA 23012 airfoil. A sinusoidal pitching motion with a 10° amplitude and a reduced frequency of 0.1 is imposed around two different mean angles of attack of 10° and 15°. The comparison of the airloads curves and of the pressure distribution over the airfoil surface shows that a three-dimensional numerical model can better reproduce the flow structures and the airfoil performance for the deep dynamic stall regime. Also, the vortical structures observed by PIV in the flow field are better captured by the three-dimensional model. This feature highlighted the relevance of three-dimensional effects on the flow field in deep dynamic stall.     

Aerodynamic and energy-efficiency-based assessment of plasma actuator's position on a NACA0015 airfoil

In recent years, there has been an increase in the number of research papers on plasma and its use in active flow control applications. The main objective of this study is to assess the plasma actuator's position on a NACA0015 airfoil in terms of aerodynamic forces. In addition, optimization of the plasma actuator's position and its configuration are studied in order to identify the optimum configuration for improvement in lift coefficient. The experiments are conducted in an open-suction-type wind tunnel at Reynolds numbers of 48,000, 75,000, and 100,000. The plasma actuators are mounted on various positions (x/C) starting from the leading edge to trailing edge of the airfoil. The experimental results on aerodynamic force measurement are presented to illustrate the increasing lift effect of the generated plasma. It is also shown that the plasma actuators used as an active flow control device appears to shift the stall angle of the airfoil. The results of the experimental study suggest that the energy efficiency of airborne systems can be improved with the use of plasma actuators due to its increasing lift coefficient effect. This result becomes a vital finding considering that the same flight can be achieved with less fuel and less amount of environmental pollution for the same distance of journey. It is also worth mentioning that increasing lift effect would mean taking off from a shorter runway or allowing the airborne vehicle with the ability to fly with additional payload.