Single polymer molecules adsorbed to mica and the oppositely charged polymer/surfactant complexes formed at the air–water interface visualized by atomic force microscopy

In the present study, the structure and morphology of single sodium poly(styrenesulfonate) (PSS) molecules adsorbed to mica surface from the natural aqueous solution is investigated using atomic force microscopy technique. Results show that single PSS molecules are observed which show a morphology of wormlike coils. Meanwhile, single sodium poly(styrenesulfonate) (PSS)/Hexadecyltrimethylammonium bromide (CTAB) complexes deposited on mica from the air–water interface are also observed. However, the PSS/CTA⁺ complexes show different conformations by appearing in the morphology of circular patches. Experimental data are in fair agreement with the theoretical analysis.     

Polymer-silica nanocomposites prepared by sol-gel technique: Nanoindentation and tapping mode AFM studies

Polymer-silica nanocomposites based on poly(2-hydroxyethyl acrylate) (PHEA) have been prepared by the simultaneous polymerization of the organic and the silica phases in a sol-gel process with the silica precursor tetraethyl orthosilicate (TEOS). The structure of this system is investigated using atomic force microscopy (AFM) in the tapping mode and in nanoindentation experiments. The structure of the PHEA/silica hybrids strongly depends on the ratio of both components in the system. For silica weight fractions lower than 0.15, the system consists of aggregated silica particles dispersed in the organic matrix; above that concentration of silica the structure is co-continuous with that of the organic matrix, similarly to two interpenetrated networks.     

Colloidal forces between bitumen surfaces in aqueous solutions measured with atomic force microscope

Colloidal forces between bitumen surfaces in aqueous solutions were measured with an atomic force microscope (AFM). The results showed a significant impact of solution pH, salinity, calcium and montmorillonite clay addition on both long-range (non-contact) and adhesion (pull-off) forces. Weaker long-range repulsive forces were observed under conditions of lower solution pH, higher salinity and higher calcium concentration. Lower solution pH, salinity and calcium concentration resulted in a stronger adhesion forces. The addition of montmorillonite clays increased long-range repulsive forces and decreased adhesion forces, particularly when co-added with calcium ions. The measured force profiles were fitted with extended DLVO theory to show the repulsive electrostatic double layer and attractive hydrophobic forces being the dominant components in the long-range forces between the bitumen surfaces. At a very short separation distance (less than 4–6 nm), a strong repulsion of steric origin was observed. The findings provide a fundamental understanding of bitumen emulsion stability and a mechanism of bitumen “aeration” in bitumen recovery processes from oil sands.     

金纳米粒子在氨基表面上的组装-pH值的影响

用原子力显微镜（AFM）和表面增强喇曼光谱（SERS）研究了pH值对金纳米粒子在Au／巯基苯胺自组装膜表面上组装效果的影响．AFM结果表明，金纳米粒子在表面上的覆盖度随pH值表现出规律性的变化，巯基苯胺自组装膜的SERS强度随pH值的变化也有类似的趋势．在磁性环境下，氨基未质子化，金粒子难以组装上，而在酸性条件下，氨基质子化带正电，金粒子与基底容易结合．我们认为金纳米粒子和氨基之间的作用属于静电力，pH值同时影响膜表面氨基的质子化程度和金纳米粒子表面的带电量．     

Analogy in adsorption behavior of homopolyelectrolyte mixtures as compared to analogous diblock polyampholytes

The adsorption behavior of aqueous mixtures of the homopolyelectrolytes poly(methacrylic acid) (PMAA) and poly[(dimethylamino)ethyl methacrylate] (PDMAEMA) was investigated in comparison with the adsorption of the ampholytic diblock copolymer PMAA‐b‐PDMAEMA on silicon substrates. Ellipsometry was used to determine the amount of adsorbed homopolyelectrolyte and diblock polyampholyte. Furthermore, the topography of the adsorbed polymers was investigated with atomic force microscopy (AFM) and compared with the structures observed in aqueous solutions by dynamic light scattering (DLS). For all types of investigated polyelectrolytic mixtures or the single polyampholyte, the adsorption was strongly influenced by the pH of the polymer solution. Although single homopolyelectrolytes showed only one maximum in adsorption according to their charge, the mixtures made from these homopolyelectrolytes showed two or three maxima. The third maximum near the isoelectric point of the mixture was assigned to a new species formed by aggregation of the two homopolyelectrolytes. Altogether, the adsorption behavior of the polyelectrolytic mixtures was in between the behavior of the pure homopolyelectrolytes and the analogous polyampholytes and therefore understandable from both of these polymer species. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 338–345, 2002; DOI 10.1002/polb.10091     

NANOMECHANICAL MAPPING OF CARBON BLACK REINFORCED NATURAL RUBBER BY ATOMIC FORCE MICROSCOPY

Atomic force microscopy （AFM） has the advantage of obtaining mechanical properties as well as topographic information at the same time. By analyzing force-distance curves measured over two-dimensional area using Hertzian contact mechanics, Young＇s modulus mapping was obtained with nanometer-scale resolution. Furthermore, the sample deformation by the force exerted was also estimated from the force-distance curve analyses. We could thus reconstruct a real topographic image by incorporating apparent topographic image with deformation image. We applied this method to carbon black reinforced natural rubber to obtain Young＇s modulus distribution image together with reconstructed real topographic image. Then we were able to recognize three regions; rubber matrix, carbon black （or bound rubber） and intermediate regions. Though the existence of these regions had been investigated by pulsed nuclear magnetic resonance, this paper would be the first to report on the quantitative evaluation of the interfacial region in real space.     

Combining thermal analysis with other techniques to monitor the decomposition of poly(m-phenylene isophthalamide)

The pyrolysis behaviour of Nomex, poly(m-phenylene isophthalamide) fibres under argon has been investigated up to a temperature of 1173 K with different methods to get direct information on the progressive changes taking place in the solid material and its carbon fibre residues. The main stages of the pyrolytic degradation of the fibres were determined by thermal analysis (TG and DTA) and their chemical and morphological evolution through the different steps was subsequently followed by Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM) measurements, respectively, on samples treated to various temperatures. This revised version was published online in July 2006 with corrections to the Cover Date.     

Surface film formation on a graphite electrode in Li‐ion batteries: AFM and XPS study

The formation of a passivation film (solid electrolyte interphase, SEI) at the surface of the negative electrode of full LiCoO₂/graphite lithium‐ion cells using LiPF₆ (1M ) in carbonate solvents as electrolyte was investigated by means of x‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The analyses were carried out at different potentials of the first and the fifth cycles, showing the potential‐dependent character of the surface‐film species formation. These species were mainly identified as Li₂CO₃ up to 3.8 V and LiF up to 4.2 V. This study shows the formation of the SEI during charging and its partial dissolution during discharge. Copyright © 2005 John Wiley & Sons, Ltd.     

Atomic Force Microscopy Study of TiO2 Films Obtained by the Sol-Gel Method

Atomic Force Microscopy (AFM) was used to study the influence of thermal treatments on the structural and textural properties of the sol-gel TiO2 films obtained from Ti(OC3H7i)4. X-ray diffraction (XRD), ellipsometric and porosity measurements have also been made.The TiO2 sol-gel films were homogeneous, transparent and amorphous. Heat treatments in the 400–600°C range indicate that the films have a strong tendency to crystallization. The high initial homogeneity of the TiO2 films was preserved during the crystallization process. AFM shows that the thermally treated films exhibit uniform, monodispersed crystals.     

聚(ε-己内酯)薄膜结晶形貌及分子取向研究

用匀胶机通过溶液铸膜方法在硅片和铝箔基板上分别制备具有不同厚度的聚(ε-己内酯)(PCL)薄膜. 通过原子力显微镜(AFM)和偏光衰减全反射傅里叶红外光谱(ATR-FTIR)对薄膜中PCL的结晶形貌、 片晶生长方式及分子链取向进行了研究. AFM结果表明, 在200 nm或更厚的薄膜中, PCL主要以侧立(edge-on)片晶的方式生长; 对于厚度小于200 nm的薄膜, PCL片晶更倾向于以平躺(flat-on)的方式生长. 这种片晶生长方式的改变在硅片和铝箔基板上都表现出同样的倾向. 此外, 在15 nm或更薄的薄膜中, PCL结晶由通常的球晶结构变为树枝状晶体. 偏光ATR-FTIR结果表明, 当膜厚小于200 nm时, 薄膜结晶中PCL分子链沿垂直于基板表面方向取向, 并且膜越薄, 取向程度越高, 与AFM的观测结果一致.