Co-Fe/SBA-15与过一硫酸盐联用非均相催化降解水中染料罗丹明B

由于硫酸根自由基(SO4?-)的强氧化性,基于SO4?-的高级氧化技术受到人们的高度关注.采用过渡金属活化过一硫酸盐(PMS)产生SO4?-用以分解有机物,反应体系简单,反应条件温和,且不需要额外的能量供给,因此,成为人们优先选用的方法,其中,采用高效、环境友好的非均相过渡金属催化剂活化PMS处理难降解有机物成为研究热点.本文研究了非均相CoFe/SBA-15-PMS体系对水中难降解染料罗丹明B(RhB)的降解.以SBA-15为载体, Co(NO3)2·6H2O和Fe(NO3)3·9H2O为前驱物,采用一步等体积浸渍法制备了CoFe/SBA-15,通过X射线衍射(XRD)、N2吸附-脱附、扫描电镜(SEM)、能谱(EDS)、透射电镜(TEM)和振动样品磁强计(VSM)等对其进行了表征.考察了焙烧温度、Co与Fe的负载量对CoFe/SBA-15催化性能的影响和该催化剂的重复使用性能,还考察了RhB降解动力学及催化剂CoFe/SBA-15投加量、氧化剂PMS投加量和反应物(RhB和PMS)初始浓度对其性能的影响,探讨了RhB的降解机理.结果表明：对于催化剂CoFe/SBA-15,合成焙烧后在SBA-15上负载的Fe、Co化合物主要是CoFe2O4复合物,它作为催化剂的活性中心负载在SBA-15的孔道内外.制备的焙烧温度对CoFe/SBA-15催化性能几乎无影响,但对Co浸出影响显著.与SBA-15相比,催化剂10Co9.5Fe/SBA-15-700(Co和Fe负载量分别为10 wt%和9.5 wt%,焙烧温度700 oC)的比表面积、孔体积和孔径均减小,分别为506.1 m2/g,0.669 cm3/g和7.4 nm,但仍然保持SBA-15的有序六方介孔结构.该催化剂以棒状体的聚集态存在,聚集体直径大于0.25μm,其磁化强度为8.3 emu/g,因此,可通过外磁铁容易地从水中分离.相比之下,10Co9.5Fe/SBA-15-700具有最佳的催化性能和稳定性,可使RhB的降解率达到96%以上, Co的浸出量小于32.4μg/L.在CoFe/SBA-15和PMS共存下, RhB的降解符合一级动力学方程, RhB降解速率随CoFe/SBA-15和PMS投加量的增加和初始反应物浓度的减小而提高.淬灭实验结果表明,在CoFe/SBA-15, PMS和RhB水溶液体系中,存在的主要活性自由基为SO4?-,它是由CoFe/SBA-15活化PMS产生的,对RhB的降解起决定性的作用. RhB降解过程的UV-vis结果表明, RhB的降解途径主要是蒽环打开, SO4?-优先攻击RhB的有色芳香烃环,然后RhB进一步分解为小分子有机物. CoFe/SBA-15循环使用10次仍能保持高催化活性和稳定性,在每次反应中RhB的降解率均大于84%, Co和Fe的浸出量均分别小于72.1和35μg/L. CoFe/SBA-15作为高效、环境友好的非均相催化剂可有效地活化PMS产生SO4?-降解水中RhB,具有实际应用的潜力.     

Acetate platinum(II) compound with 5,7-ditertbutyl-1,2,4-triazolo[1,5-a]pyrimidine that overcomes cisplatin resistance: structural characterization,in vitro cytotoxicity,and kinetic studies

The reaction of silver acetate with cis-[PtI₂(dbtp)₂], where dbtp = 5,7-ditertbutyl-1,2,4-triazolo-[1,5-a]pyrimidine, yielded cis-[Pt(OOCCH₃)₂(dbtp)₂]·dmf (1). The complex has been analyzed by multinuclear magnetic resonance (¹H, ¹³C, ¹⁵N), IR, and Raman. The compound formed two rotamers in CDCl₃ and its spatial structures have been optimized using computational calculation. It was found that head-to-tail rotamer (1a) is more stable than its head-to-head counterpart (1b). In vitro antiproliferative activity against four tumor cell lines (A549, T47D, FaDu, and A2780cis) revealed in all cases significant cytotoxicity (IC₅₀ = 0.26–1.80 μM), possessing IC₅₀ values at least fivefold lower than cisplatin, carboplatin, and oxaliplatin (except A2780cis). The remarkable in vitro activity against T47D and A2780cis suggested the ability to overcome cisplatin resistance in these types of tumor cells. In addition, in vitro toxicity was evaluated against BALB/3T3 and has shown that the lipophilic platinum(II) complex (1) inhibits cell proliferation weaker than cisplatin and oxaliplatin. Additionally, cis-[Pt(OOCCH₃)₂(dbtp)₂]·dmf exhibited selective activity, in contrast to cisplatin or oxaliplatin.     

Lipoxygenase inhibitory activity of Cuspidaria pulchra and isolated compounds

This work evaluated the in vitro inhibitory activity of the crude ethanolic extract from the aerial parts of Cuspidaria pulchra (Cham.) L.G. Lohmann against 15-lipoxygenase (15-LOX). The bioassay-guided fractionation of the n-butanol fraction, which displayed the highest activity, led to the isolation of three compounds: caffeoylcalleryanin (1), verbascoside (2) and 6-hydroxyluteolin-7-O-β-glucoside (3). Assessment of the ability of the isolated compounds to inhibit 15-LOX revealed that compounds 1, 2 and 3 exerted strong 15-LOX inhibitory activity; IC₅₀ values were 1.59, 1.76 and 2.35 μM respectively. The XTT assay showed that none of the isolated compounds seemed to be significantly toxic.     

Fast determination of Ziziphora tenuior L. essential oil by inorganic–organic hybrid material based on ZnO nanoparticles anchored to a composite made from polythiophene and hexagonally ordered silica

In this paper, for the first time, an inorganic–organic hybrid material based on ZnO nanoparticles was anchored to a composite made from polythiophene and hexagonally ordered silica (ZnO/PT/SBA-15) for use in solid-phase fibre microextraction (SPME) of medicinal plants. A homemade SPME apparatus was used for the extraction of volatile components of Ziziphora tenuior L. A simplex method was used for optimisation of five different parameters affecting the efficiency of the extraction. The main constituents extracted by ZnO/PT/SBA-15 and PDMS fibres and hydrodistillation (HD) methods, respectively, included pulegone (51.25%, 53.64% and 56.68%), limonene (6.73%, 6.58% and 8.3%), caryophyllene oxide (5.33%, 4.31% and 4.53%) and 1,8-cineole (4.21%, 3.31% and 3.18%). In comparison with the HD method, the proposed technique could equally monitor almost all the components of the sample, in an easier way, in a shorter time and requiring a much lower amount of the sample.     

Effect of the order of Ni and Ce addition in SBA-15 on the activity in dry reforming of methane

Dry reforming of methane has been carried out on SBA-15 catalysts containing 5 wt% Ni and 6 wt% Ce. The effect of the order of Ni and Ce impregnation on the catalytic activity has been studied. Both metals were added using the “two-solvent” method that favors metal dispersion inside the pores. Characterizations by XRD (low and high angles), N₂ sorption, SEM and TEM of the materials after metal addition and calcination indicate good preservation of the porosities and high NiO and CeO₂ dispersion inside the porous channels. Reduction was carried out before the catalytic tests and followed by TPR measurements. The most active reduced catalyst was the Ni–Ce/SBA-15 sample prepared by impregnating cerium first, then nickel. All catalysts were highly active and selective towards H₂ and CO at atmospheric pressure. Full CH₄ conversion was obtained below 650 °C. The higher performances compared to those reported in the literature for mesoporous silica with supported Ni and Ce catalysts are discussed.     

One pot synthesis of chromium incorporated SBA-16 under acid medium-Application in the selective oxidation of benzyl alcohol derivatives

Cr-SBA-16 mesoporous silica heterogeneous catalysts (Si/Cr = 7, 14, and 28) were successfully synthesized by one-pot hydrothermal method at low acidic medium. The catalysts were characterized by means of X-ray diffraction (XRD), N₂ adsorption-desorption at 77 K, Fourier Transform Infrared (FTIR), X-ray photoelectron (XPS) and Diffuse Reflectance UV–Vis (DRS) Spectroscopies, Thermogravimetric analysis (TGA), Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM) techniques. Herein, Cr-SBA-16 catalysts are evaluated in the selective catalytic oxidation of benzyl alcohol derivatives using H₂O₂ as oxidant. From XPS and UV–Vis (DRS) spectroscopies the molar ratios between Cr⁶⁺/Cr³⁺ are found to increase versus chromium loading in the following order: Cr-SBA-16(28) < Cr-SBA-16(14) < Cr-SBA-16(7). Hence the highest Cr⁶⁺ in tetrahedrally environment is observed for Si/Cr = 7. We demonstrated for the first time that the selective catalytic oxidation of benzyl alcohol (BzOH) using H₂O₂ over Cr-SBA-16 occurs through noncompetitive adsorption mechanism and the reaction is pseudo-first order to BzOH. The activity of the reaction depends on the symmetry of chromium species, herein, high activity is observed for tetrahedral chromium species in Cr-SBA-16(7). The absence of any chromium ions in the filtrate shows no chromium leaching from the silica framework.     

Mg/Ce-SBA-15的制备及其苯酚甲醇烷基化性能的研究

以Ce-SBA-15为载体,硝酸镁为活性组分前驱体,通过浸渍法制备了Mg/Ce-SBA-15催化剂。利用XRD、N₂吸附-脱附、SEM、EDS、NH₃-TPD、Py-FTIR和TG-DTA手段对催化剂进行表征。结果表明,Mg掺杂并未破坏载体结构,催化剂表面弱酸含量有所增加,L酸增加明显。在固定床反应器中评价了Mg/Ce-SBA-15分子筛催化苯酚甲醇烷基化的反应性能。结果表明,Mg负载量为7%、焙烧温度为550℃、焙烧时间为4.5 h制备的Mg/Ce-SBA-15催化剂催化效果最佳。在反应温度460℃,n（苯酚）：n（甲醇）为1：4,质量空速为3.0 h^-1,常压的条件下,苯酚转化率为80.1%,邻甲酚选择性为86.4%。     

Hβ/Al-SBA-15介微孔复合分子筛负载Ni-W催化剂对萘加氢裂化制BTX的催化性能

采用后合成法制备Hβ/Al-SBA-15复合分子筛,利用XRD、N_2吸附、Py-IR、NH_3-TPD、SEM和TEM等手段进行表征。用浸渍法将Ni-W活性组分担载在Hβ/Al-SBA-15载体上,制备Ni-W/Hβ/Al-SBA-15催化剂,以萘为模型化合物,考察该催化剂的加氢裂化性能。结果表明,所合成的Hβ/Al-SBA-15复合分子筛既有介孔结构又有微孔结构,并同时具有B酸和L酸中心,酸性强于SBA-15。具有适度酸性位和介微孔结构的Ni-W/Hβ/Al-SBA-15催化剂,对萘加氢裂化具有较高的萘转化率和BTX选择性,分别为96%和61.1%。     

氮化SBA-16负载镍基催化剂的制备及其对甲烷二氧化碳重整反应的催化性能

通过软模板法合成了SBA-16分子筛,采用高温氨气氮化的方法使有序介孔硅材料中的氧原子部分被氮原子取代,得到氮化的SBA-16载体(SBA-16-N)。采用满孔浸渍法制备了镍基催化剂,并将制得的Ni/SBA-16和Ni/SBA-16-N催化剂用于甲烷二氧化碳重整反应。通过透射电镜、氮气物理吸附、X射线衍射、X射线光电子能谱和二氧化碳程序升温脱附等手段研究了载体和催化剂的结构,并利用热重分析对反应之后回收催化剂进行了表征。结果表明,高温氮化后的分子筛中掺入了氮元素,增加了载体的碱性,改善了载体对反应气体的吸附活化能力,增强了载体与金属之间的相互作用,从而提高了催化剂的活性和抗积炭性能。