High-power diode-pumped mode-locked Yb:YAG ceramic laser

A high-power diode-pumped passively mode-locked Yb:YAG ceramic laser was demonstrated. An average output power of 3.80W with a pulse duration of 433 fs at a repetition rate of 90.9MHz was obtained at a wavelength of 1050 nm using a 2% output coupler. A peak power of 96.5kW was also obtained. To the best of our knowledge, these are the highest reported average power and peak power for a diode-pumped mode-locked Yb:YAG ceramic laser.     

Three-dimensional printing of conducting polymer microstructures into transparent polymer sheet: Relationship between process resolution and illumination conditions

Three-dimensional (3D) polypyrrole microstructures were successfully obtained in a transparent polymer sheet by 3D scanning of the laser focal point. The lateral process resolution of the microstructures was studied under different photofabrication conditions such as the repetition rate of the femtosecond pulse laser and the waiting time of the laser focal point scanning. As a result, a very small line width of the polypyrrole deposition of less than 500 nm was realized with good reproducibility.     

Radical Graft Polymerization of Vinyl Monomers Initiated by A20 Groups Introduced Onto a Carbon Black Surface: Effect of azo Groups on Graft Polymerization

The radical graft polymerization of vinyl monomers from carbon black initiated by azo groups introduced onto the surface was investigated. The introduction of azo groups onto carbon black surface was achieved by three methods: the reaction of 2,2′-azobis[2-(2-imidazolin-2-yl)propane] (AIP) with (1) epoxide groups, which were introduced by the reaction of carbon black with chlorometh-yloxirane; (2) acyl chloride groups, which were introduced by the reaction of carboxyl groups on the surface with thionyl chloride; and (3) 3-chloroformyl-1-cyano-1-methylpropyl groups, which were introduced by the reaction of carbon black with 4,4′-azobis(4-cyanovaleric acid) and then thionyl chloride. The amount of azo groups introduced onto the surface by the above methods was determined to be 0.07-0.19 mmol/g. The graft polymerization of methyl methacrylate was found to be initiated by azo groups introduced onto the carbon black surface. During the polymerization, poly(methyl methacrylate) was effectively grafted onto carbon black through propagation of the polymer from the radical produced on the surface by the decomposition of the azo groups. The percentage of grafting using carbon black having azo groups introduced by method 1 increased to 40%. It was also found that the graft polymerization of several vinyl monomers such as styrene, acrylonitrile, and acrylic acid was initiated by the azo groups introduced onto the surface and the corresponding polymer was effectively grafted onto the surface. Furthermore, the effect of the amount of carbon black having azo groups on the graft polymerization was investigated.     

Heat-Resistant Polymer-Grafted Carbon Black: Grafting of Poly(Amide-Imide) Onto Carbon Black

Aromatic poly(amide-imide) with terminal isocyanate groups (PAINCO) was prepared by the polycondensation of trimellitic anhydride and a slight excess of 4,4′-diphenylmethane diisocyanate in N-methyl-2-pyrrolidone (NMP) at 160°C for 20 h. PAI was effectively grafted onto the surface by the reaction of PAI-NCO with carbon black: the percentage of grafting onto FW 200 and Neospectra II was determined to be 41.2 and 39.5%, respectively. When the carboxyl and phenolic hydroxyl groups on carbon black were blocked by treatment with diazomethane, the grafting of PAI-NCO onto the treated carbon black does not proceed. Therefore, it is concluded that PAI-NCO reacts with the carboxyl and phenolic hydroxyl groups on carbon black and PAI is grafted through amide and urethane bonds, respectively. The reaction of PAI-NCO with carbon black was accelerated by the addition of amines as catalyst and by raising of the reaction temperature. Thermogravimetric analysis indicated that PAI-grafted carbon black was stable in air up to about 300°C. The PAI-grafted carbon black was found to give a stable colloidal dispersion in NMP.     

Grafting of Polymers from Carbon Fiber. Anionic Graft Polymerization of Vinyl Monomers Initiated by Metallized Aromatic Rings on Carbon Fiber

The anionic graft polymerization of vinyl monomers onto carbon fiber initiated by metallized carbon fiber was investigated. The metalation of polycondensed aromatic rings of the carbon fiber surface was achieved by the treatment of carbon fiber with n-butyl-lithium (BuLi) in N, N, N′, N′ -tetramethylethylenediamine (TMEDA) or hexamethylphosphorous triamide (HMPT) at 0°C. The anionic polymerization of methyl methacrylate (MMA) and styrene (St) was initiated by the metallized carbon fiber, and these polymers were grafted onto the surface. The conversion and the percentage of grafting increased with increasing amount of BuLi used for the metalation of carbon fiber. When 0.20 g carbon fiber was treated with 0.3 mmol BuLi in TMEDA, the percentage of grafting of PMMA and PSt reached a maximum value (PMMA, 34.5%; PSt, 37.1 %). Furthermore, the metalation of aromatic rings of carbon fiber also proceeds by the treatment with BuLi in HMPT. On the contrary, no grafting was observed when carbon fiber was treated with BuLi in tetrahydrofuran (THF) or toluene. This may be due to the fact that metalation of carbon fiber does not proceed in THF or toluene.     

Unusually facil cis to trans isomerization of a polypropiolate bearing a long alkyl chain polymerized using a [Rh(norbornadiene)Cl]2 catalyst: An ESR study

Alkylpropiolate having n-hexadecyl moiety in the ester group was stereospecifically polymerized with a [Rh(norbornadiene)Cl]₂ complex catalyst in alcohol to give rise to cis-transoid polyacetylenes in high yields. The unusually facile cis to trans isomerization for the polymer was found to be induced when the polymer was warmed to even less than ca. 57°C. Under these conditions ESR spectra bearing hyperfine structures due to the radicals generated by the rotational scission in the cis–π bond were observed. This isomerization induced a large g value shift in the ESR spectra together with an increase of the radical concentration during the isomerization, indicating formation of planar conjugated trans sequences that stabilize mobile unpaired electrons as solitons. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2457–2461, 1998