AGE method simulations of a turbulent far‐wake compared to spectral DNS

Turbulent flow simulation methods based on finite differences are attractive for their simplicity, flexibility and efficiency, but not always for accuracy or stability. This paper demonstrates that a good compromise is possible with the advected grid explicit (AGE) method. Starting from the same initial field as a previous spectral DNS, AGE method simulations of a planar turbulent wake were carried out as DNS, and then at three levels of reduced resolution. The latter cases were in a sense large‐eddy simulations (LES), although no specific sub‐grid‐scale model was used. Results for the two DNS methods, including variances and power spectra, were very similar, but the AGE simulation required much less computational effort. Small‐scale information was lost in the reduced resolution runs, but large‐scale mean and instantaneous properties were reproduced quite well, with further large reductions in computational effort. Quality of results becomes more sensitive to the value chosen for one of the AGE method parameters as resolution is reduced, from which it is inferred that the numerical stability procedure controlled by the parameter is acting in part as a sub‐grid‐scale model. Copyright © 2002 John Wiley & Sons, Ltd.     

10,12—双炔廿三酸盐的LB膜特性研究

本文合成了10,12-双炔廿三酸,并用其在Si、SiO_2、CaF_2等基片上沉积了LB膜,结果表明,10,12-双炔廿三酸的镉盐成膜更稳定。这种LB膜在紫外光辐照下很快聚合,聚合前后的紫外-可见吸收光谱发生规律性的变化,并保持层状结构,等同周期稍变。通过红外吸收的二向色性分析,确定了该分子的取向。     

Toward low‐noise synthetic turbulent inflow conditions for aeroacoustic calculations

The accuracy of boundary conditions for computational aeroacoustics is a well‐known challenge, due in part to the necessity of truncating the flow domain and replacing the analytical boundary conditions at infinity with numerical boundary conditions. In particular, the inflow boundary condition involving turbulent velocity or scalar fields is likely to introduce spurious waves into the domain, therefore degrading the flow behavior and deteriorating the physical acoustic waves. In this work, a method to generate low‐noise, divergence‐free, synthetic turbulence for inflow boundary conditions is proposed. It relies on the classical view of turbulence as a superposition of random eddies convected with the mean flow. Within the proposed model, the vector potential and the requirement that the individual eddies must satisfy the linearized momentum equations about the mean flow are used. The model is tested using isolated eddies convected through the inflow boundary and an experimental benchmark data for spatially decaying isotropic turbulence. Copyright © 2013 John Wiley & Sons, Ltd.     

Discrete filter operators for large‐eddy simulation using high‐order spectral difference methods

The combination of a high‐order unstructured spectral difference (SD) spatial discretization scheme with sub‐grid scale (SGS) modeling for large‐eddy simulation is investigated with particular focus on the consistent implementation of a structural mixed model based on the scale similarity hypothesis. The difficult task of deriving a consistent formulation for the discrete filter within the SD element of arbitrary order led to the development of a new class of three‐dimensional constrained discrete filters. The discrete filters satisfy a set of selected criteria and are completely local within the SD element. Their weights can be automatically computed at run time from the number of solution points within each element and the expected filter cutoff length scale. The novel discrete filters can be applied to any SGS model involving explicit filtering and to a broad class of high‐order discontinuous finite element numerical schemes. The code is applied to the computation of turbulent channel flows at three Reynolds numbers, namely Re_τ = 180, 395, and 590 (based on the friction velocity u_τ and channel half‐width δ). Results from computations with and without the SGS model are compared against results from direct numerical simulation. The numerical experiments suggest that the results are sensitive to the use of the SGS model, even when a high‐order numerical scheme is used, especially when the grid resolution is kept relatively low and mostly in terms of resolved Reynolds stresses. Results obtained using existing filters based on the projection of the solution over lower‐order polynomial bases are also shown and demonstrate that these filters are inadequate for SGS modeling purposes, mostly because of their inability to enforce the selected cutoff length scale with sufficient accuracy. The use of the similarity mixed formulation proved to be particularly accurate in reproducing SGS interactions, confirming that its well‐known potential can be realized in conjunction with state‐of‐the‐art high‐order numerical schemes.Copyright © 2012 John Wiley & Sons, Ltd.     

Validation of a novel very large eddy simulation method for simulation of turbulent separated flow

The paper describes the validation of a newly developed very LES (VLES) method for the simulation of turbulent separated flow. The new VLES method is a unified simulation approach that can change seamlessly from Reynolds‐averaged Navier–Stokes to DNS depending on the numerical resolution. Four complex test cases are selected to validate the performance of the new method, that is, the flow past a square cylinder at Re = 3000 confined in a channel (with a blockage ratio of 20%), the turbulent flow over a circular cylinder at Re = 3900 as well as Re = 140,000, and a turbulent backward‐facing step flow with a thick incoming boundary layer at Re = 40,000. The simulation results are compared with available experimental, LES, and detached eddy simulation‐type results. The new VLES model performs well overall, and the predictions are satisfactory compared with previous experimental and numerical results. It is observed that the new VLES method is quite efficient for the turbulent flow simulations; that is, good predictions can be obtained using a quite coarse mesh compared with the previous LES method. Discussions of the implementation of the present VLES modeling are also conducted on the basis of the simulations of turbulent channel flow up to high Reynolds number of Re_τ = 4000. The efficiency of the present VLES modeling is also observed in the channel flow simulation. From a practical point of view, this new method has considerable potential for more complex turbulent flow simulations at relative high Reynolds numbers. Copyright © 2013 John Wiley & Sons, Ltd.     

A ghost-cell immersed boundary method for large-eddy simulations of compressible turbulent flows

A methodology to perform a ghost-cell-based immersed boundary method (GCIBM) is presented for simulating compressible turbulent flows around complex geometries. In this method, the boundary condition on the immersed boundary is enforced through the use of ‘ghost cells’ that are located inside the solid body. The computations of variables on these ghost cells are achieved using linear interpolation schemes. The validity and applicability of the proposed method is verified using a three-dimensional (3D) flow over a circular cylinder, and a large-eddy simulation of fully developed 3D turbulent flow in a channel with a wavy surface. The results agree well with the previous numerical and experimental results, given that the grid resolution is reasonably fine. To demonstrate the capability of the method for higher Mach numbers, supersonic turbulent flow over a circular cylinder is presented. While more work still needs to be done to demonstrate higher robustness and accuracy, the present work provides interesting insights using the GCIBM for the compressible flows.     

Experimental and LES investigation of premixed methane/air flame propagating in a tube with a thin obstacle

In this paper, an experimental and numerical investigation of premixed methane/air flame dynamics in a closed combustion vessel with a thin obstacle is described. In the experiment, high-speed video photography and a pressure transducer are used to study the flame shape changes and pressure dynamics. In the numerical simulation, four sub-grid scale viscosity models and three sub-grid scale combustion models are evaluated for their individual prediction compared with the experimental data. High-speed photographs show that the flame propagation process can be divided into five stages: spherical flame, finger-shaped flame, jet flame, mushroom-shaped flame and bidirectional propagation flame. Compared with the other sub-grid scale viscosity models and sub-grid scale combustion models, the dynamic Smagorinsky–Lilly model and the power-law flame wrinkling model are better able to predict the flame behaviour, respectively. Thus, coupling the dynamic Smagorinsky–Lilly model and the power-law flame wrinkling model, the numerical results demonstrate that flame shape change is a purely hydrodynamic phenomenon, and the mushroom-shaped flame and bidirectional propagation flame are the result of flame–vortex interaction. In addition, the transition from “corrugated flamelets” to “thin reaction zones” is observed in the simulation.     

Burst detection in turbulent channel flows based on large eddy simulation databases

As one of the important coherent structures in the near-wall region, turbulent burst is responsible for the production and transport of major turbulent kinetic energy and Rey- nolds stress[1]. Nearly half of turbulent kinetic energy or Reynolds stress is produced in the near-wall region, and 80% flows in outer region only contribute 20% of them. Both ejection and sweeping events contribute 60―70% of the turbulent shear stress respec- tively[2]. Recently, turbulent burst process has been foun…     

Simulation of spray combustion in a lean-direct injection combustor

Large-eddy simulation (LES) of a liquid-fueled lean-direct injection (LDI) combustor is carried out by resolving the entire inlet flow path through the swirl vanes and the combustor. A localized dynamic subgrid closure is combined with a subgrid mixing and combustion model so that no adjustable parameters are required for both non-reacting and reacting LES. Time-averaged velocity predictions compare well with the measured data. The unsteady flow features that play a major role in spray dispersion, fuel–air mixing and flame stabilization are identified from the simulation data. It is shown that the vortex breakdown bubble (VBB) is smaller with more intense reverse flow when there is heat release. The swirling shear layer plays a major role in spray dispersion and the VBB provides an efficient flameholding mechanism to stabilize the flame.