Assessing contaminated hydrogen peroxide for safe storage and transportation using the FTAI

Hydrogen peroxide is a very versatile oxidizing agent, and it is also environmentally compatible considering that the products of its exothermic decomposition are oxygen and water.When kept in a clean temperature-controlled environment, the self-reaction (decomposition) rate is extremely low. However, it is well known that even a small amount of contamination will dramatically increase the reaction rate. This paper describes the use of the fast thermal activity interpreter (FTAI) instrument to examine the chemical reactivity of commercially available 50% hydrogen peroxide at two different temperatures (30 and 40°C) both with and without contamination. The results show that at 30°C a small amount of rust (330 ppm) increases the reaction rate of 50% hydrogen peroxide by a factor of 50. When the temperature is increased to 40°C, the reaction rate is further increased by almost a factor of four. The implication for reactivity management is that at this contamination level most practical vessel sizes would require emergency venting capability. An evaluation was then performed to determine the emergency venting requirement for the safe transportation or storage of the contaminated hydrogen peroxide. It was determined that for quantities of the material less than 5 gallons, conventional breather vents would be sufficient to accommodate the gas evolved. However, for larger quantities, a safety relief device would be needed. For example, for a 400-gallon tote bin at 40°C the required minimum vent area is estimated to be 4.3 in², corresponding to a minimum vent diameter of 2.3 inches.     

Thermal decomposition of a generation 4.5 PAMAM dendrimer platinum drug conjugate

A nanoscale multivalent platinum drug based on a poly(amidoamine) [PAMAM] dendrimer (generation 4.5, carboxylate surface) has been synthesized and fully characterized using a variety of spectroscopic, chromatographic and thermal methods. Treatment of the dendrimer with an aqueous solution containing an excess diaquo(cis-1,2-diaminocyclohexane)platinum(II) produces a conjugate containing approximately forty (diaminocyclohexane)platinum(II) moieties at the surface of the dendrimer. This material undergoes smooth two-stage thermal decomposition to provide residual platinum oxide reflecting the platinum loading in the drug.     

纳米颗粒悬浮液池内泡状沸腾的实验研究

本文对纳米颗粒悬浮液在平壁面上池内沸腾进行了实验研究。实验用的纳米粒子为26 nm的铁粉和13 nm的三氧化二铝纳米粉末,基液为去离子水。分别配成体积浓度为0．1％, 1％和2％的悬浮液。实验结果表明,纳米悬浮颗粒对液体沸腾换热过程的影响会随着纳米颗粒性质,颗粒浓度及热流密度大小的不同而出现不同的效果;加入纳米颗粒后, 对基液沸腾换热的影响存在着两个相反的作用机制,它们分别为:纳米颗粒增强了液体内部的热量迁移能力(热物性的影响)和改变了加热面的表面结构特性(加热面特性的影响)。     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

镍-酸性铬兰K络合物吸附波

用微分脉冲溶出伏安法研究了镍(11)与酸性铬兰K(ACBK)所生成的络合物在悬汞电极上的电化学特性及电化学反应机理，发现电极反应为镍与酸性铬兰K所生成的络合物吸附在电极表面后发生的不可逆还原。在HCl-硼砂介质中(pH8．67)，络合物在-316mV处有一吸附还原峰，其峰电流与镍浓度在0．001～0．010μ/mL范围内呈现良好的线性关系，其最低检出浓度为0．0005μg／mL。     

Effect of Hydrolysis Conditions on the Direct Formation of Nanoparticles of Ceria–Zirconia Solid Solutions from Acidic Aqueous Solutions

The effect of the cation concentration, hydrolysis temperature, and composition in the CeO₂–ZrO₂ system on the direct precipitation of ceria–zirconia solid solutions and the structure of the precipitates from acidic aqueous solutions of (NH₄)₂Ce(NO₃)₆ and ZrOCl₂ by hydrolysis under hydrothermal conditions were investigated. Nanometer-sized (8–10 nm) ceria–zirconia solid solution particles in a composition range of 0 to 60 mol% ZrO₂ were directly precipitated from the solutions with total metal cation concentration less than 0.2 mol/dm³ by simultaneous thermal hydrolysis at 150–240°C. The crystalline phase of the precipitates gradually changed from cubic and/or tetragonal to monoclinic with increasing the cation concentration of the solution from 0.2 to 0.8 mol/dm³ at the starting composition of 50 mol% ZrO₂ under hydrolysis condition of 150°C for 48 h, which was attributed to decrease in the supply of hydrolyzed Ce component caused by decrease in the hydrolysis ratio of (NH₄)₂Ce(NO₃)₆. Ceria–zirconia solid solutions containing large amount of ZrO₂ maintained high specific surface area and small-sized crystallite after heat-treatment at 900–1000°C for 1 h.     

稀薄气体二维外部柱体绕流特性研究

本文采用直接模拟蒙特卡罗方法对稀薄气体二维外部柱体绕流问题进行了数值模拟。结果表明:外部绕流问题,在特定情况下会产生激波,激波的产生,不仅与气体的稀薄程度有关,还与来流马赫数有关。而气流与壁面之间的换热,随来流马赫数增加而增加,随气体稀薄程度增加而减小。     

Finite-Dimensional Approximations for Scattering Theory Operators in the Wave-Packet Representation

We consider some types of packet discretization for continuous spectra in quantum scattering problems. As we previously showed, this discretization leads to a convenient finite-dimensional (i.e., matrix) approximation for integral operators in the scattering theory and allows reducing the solution of singular integral equations connected with the scattering theory to some suitable purely algebraic equations on an analytic basis. All singularities are explicitly singled out. Our primary emphasis is on realizing the method practically.     

Dynamic mechanical thermal analysis transitions of partially and fully substituted cellulose fatty esters

The main transitions of cellulose fatty esters with different degrees of substitution (DSs) were investigated with dynamic mechanical thermal analysis. Two distinct main relaxations were observed in partially substituted cellulose esters (PSCEs). They were attributed to the glass‐transition temperature and to the chain local motion of the aliphatic substituents. The temperatures of both transitions decreased when DS or the number of carbon atoms (n) of the acyl substituent increased. Conversely, all the transitions of fully substituted cellulose esters occurred within a narrow temperature range, and they did not vary significantly with n. This phenomenon was explained by the formation of a crystalline phase of the fatty substituents. The presence of few residual OH groups in PSCEs was responsible for a large increase in the storage bending modulus, and it eliminated the effect of n on damping. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 281–288, 2003     

Laser spectroscopic investigation of a new precursor-type polyparaphenylenevinylene

Optical, structural and morphological properties of thin films of polyparaphenylenevinylene (PPV) formed by an alkyl sulfinyl precursor route have been studied. Thin films were fabricated on an optical glass and on quartz glass either by spin-coating of the precursor solution or by layer-by-layer deposition using Langmuir–Blodgett technique. PPV precursor films were also spin-coated on gold-coated glass in order to study thin-film optical parameters by surface plasmon spectroscopy. We have been successful in forming about 40 precursor mono layers on quartz glass by Langmuir–Blodgett technique using optimized surface pressure and dipping conditions. After thermal conversion of the precursor layers good quality fluorescent PPV films of yellow colour have been obtained. Optical characterization of the films was carried out by linear absorption and emission spectroscopy, ellipsometry, and surface plasmon spectroscopy. Structural and morphological studies on the thin films were carried out by using X-ray scattering and atomic force microscopy. Wave-guided travelling-wave laser action has been achieved in a PPV film on quartz glass. The sample was transversally pumped with picosecond laser pulses (wavelength 347.15 nm, duration 35 ps). Laser emission occurred at 550 nm for pump pulse energy densities above .