Thermoresponsive polymersome from a double hydrophilic block copolymer

The article describes synthesis and thermally triggered self‐assembly of a Poly (ethylene oxide)‐block‐poly (N‐insopropylacrylamide) (PEO‐b‐PNIPAm) in aqueous medium. At rt, the polymer remains as unimer, however, at lower critical solution temperature (LCST) of PNIPAm (32 °C), it forms a rather large undefined aggregate which at slightly elevated temperature (～40 °C) converges to well defined polymersome structure (Critical aggregation concentration = 0.45 mg/mL) with hydrodynamic diameter of 40–50 nm. By lowering the temperature, initial swelling of the compact vesicle followed by reversible disassembly to unimer was noticed. The polymersome exhibits encapsulation ability to a hydrophilic dye Calcein which can be spontaneously released by lowering the temperature below cloud point. Likewise a hydrophobic dye namely 8‐Anilino‐1‐naphthalenesulfonic acid (ANS) can also be encapsulated and released by thermal trigger. Detail photoluminescence studies reveal ANS dye can be used as a generalized probe molecule for detecting LCST of a thermoresponsive polymer by “fluorescence on” above LCST even by cursory observation. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2444–2451     

Simultaneous detection of ammonia and humidity using transmission surface plasmon resonance technique

Abstract

Gas sensing by using the transmission surface plasmon resonance (T-SPR) technique was demonstrated. Polyacrylic acid (PAA)/5-nm-thick gold/40-nm-thick silver/polycarbonate grating substrate structure (Sensor A) responded to ammonia; however, it exhibited a strong humidity dependence. Polyvinyl alcohol (PVA)/5-nm-thick gold/40-nm-thick silver/polycarbonate grating substrate structure (Sensor B) as the sensing material was also prepared and it mainly responded to humidity. The T-SPR properties of Sensors A and B were observed simultaneously by a stacking arrangement that enabled us to obtain the responses by using a single spectrophotometer. The ammonia concentration under various humidity conditions could be accurately obtained by simultaneous measurement of Sensors A and B.     

内爆驱动式超高速发射技术的初步研究

为获得10 km/s左右的超高速发射能力,以内爆发射器为研究对象,利用AUTODYN 2D软件对口径为8 mm的内爆发射器进行有限元仿真分析,获得了典型状态下的弹丸发射速度。研制了口径为8 mm的内爆发射器,并在压缩管中填充5 MPa氦气进行实验,分别获得了0.55 g铝合金弹丸7.95 km/s和0.37 g镁合金弹丸10.28 km/s的发射速度,与有限元仿真计算结果的速度偏差分别为15.3%和3.7%。结果表明,设计的内爆发射器具备10 km/s发射能力,满足空间碎片撞击和防护研究的超高速发射需求。     

An experimental investigation on heat transfer enhancement in circular jet impingement on hot surfaces by using Al2O3/water nano-fluids and aqueous high-alcohol surfactant solution

The present article reports the heat transfer characteristics of a vertical stainless steel foil of 0.15 mm thickness (SS304) by circular impinging jets of various fluids such as pure water, nano-fluids (Al₂O₃-water, ф = 0.15%, 0.6%), and aqueous high-alcohol surfactant (HAS, i.e., 2-ethyl-hexanol, 100–400 ppm) studied using an infrared thermal imaging camera (A655sc, FLIR System). The enhancement in the heat transfer rates for Al₂O₃-water nano-fluids with ф = 0.15%, ф = 0.60%, and aqueous surfactant solution (150ppm) is found to be 140%, 207%, and 117% higher compared to pure water results, respectively. The surface characteristics of the foil after jet impingement by various fluids are also studied using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), and surface wettability.     

地下水脆弱性风险预警和评估的区间三角模糊多属性决策模型

应用基于逼近理想解排序法的区间三角模糊多属性决策模型,对三江平原六大分区地下水脆弱性进行了风险预警和评估.评估结果与前人吻合,可为有关决策部门采取相应降低环境风险的措施提供参考.实例验证表明,模型具有更高的计算精度和更好的评价效果,为有关环境风险决策部门对地下水风险预警和评估提供了新的思路和方法.     

The local ultraconvergence of high‐order finite element method for second‐order elliptic problems with constant coefficients over a rectangular partition

In this article, we will discuss the local ultraconvergence of high‐degree finite element method based on a rectangular partition for the second‐degree elliptic problem with constant coefficients in Ω ? ?² , u( y ) = 0 on ?Ω . Based on suitable regularity, ultraconvergence of the displacement of the extrapolated kth (k ≥ 3) degree finite element solution has been obtained by an extrapolation technique. Finally, numerical experiments are applied to demonstrate our theoretical findings.     

Dynamic response of a growing inclusion in a discrete system

The propagation of a semi-infinite line defect, contained in an infinite square-cell lattice is considered. The defect is composed of particles lighter than those in the ambient lattice and it is assumed this defect propagates with constant speed. Dispersion properties of the lattice are related to waves generated by the propagating defect. In order to determine these properties, the Wiener–Hopf technique is applied. Additional features, related to localisation along the defect are also identified. Analysis of the dispersion relations for this lattice, from the kernel function inside the Wiener–Hopf equation, is carried out. The solution of the Wiener–Hopf equation is presented for the case when an external load is applied corresponding to an energy flux at infinity.     

Generation of linear and nonlinear waves in numerical wave tank using clustering technique-volume of fluid method

A two-dimensional (2D) numerical model is developed for the wave simulation and propagation in a wave flume.The fluid flow is assumed to be viscous and incompressible,and the Navier-Stokes and continui...