润滑油对基于制冷循环的喷雾冷却系统性能的影响

针对高功率固体激光器的散热需求,设计了一种基于制冷循环的喷雾冷却系统,并对其换热性能进行研究。由于制冷系统的压缩机需要润滑,冷却液中不可避免地会混有润滑油。润滑油会对冷却液的粘度、表面张力产生影响,并可能产生油膜,从而对冷却液的换热过程产生强化或抑制。因此,通过实验研究,分析了润滑油对喷雾冷却换热性能的影响。实验结果表明,冷却液中存在润滑油,会增大冷却液流经喷嘴过程中的阻力,减小流量,但根据本系统的应用情况,可以忽略;在低热流密度时,含有一定量的润滑油更有利于热源表面温度的均匀分布,高热流密度时,2%(质量分数)的含油量对温度分布不均的影响可以忽略;润滑油的存在可以提高临界热流密度,使得系统的散热能力得到提高,更有利于其在高功率固体激光器散热领域的应用。     

A comparative study on structural and optical properties of ZnO and Al-doped ZnO thin films obtained by ultrasonic spray method using different solvents

Transparent conducting ZnO and Al doped ZnO thin films were deposited on glass substrate by ultrasonic spray method. The thin films with concentration of 0.1 M were deposited at 350 °C with 2 min of deposition time. The effects of ethanol and methanol solution before and after doping on the structural, optical and electrical properties were examined. The DRX analyses indicated that ZnO films have nanocrystalline nature and hexagonal wurtzite structure with (1 0 0) and (0 0 2) preferential orientation corresponding to ZnO films resulting from methanol and ethanol solution, respectively. The crystallinity of the thin films improved with methanol solution after doping to (0 0 2) oriented. All films exhibit an average optical transparency about 90%, in the visible range. The band gaps values of ZnO thin films are increased after doping from 3.10 to 3.26 eV and 3.27 to 3.30 eV upon Al doping obtained by ethanol and methanol solution, respectively. The electrical conductivity increase from 7.5 to 15.2 (Ω cm)⁻¹ of undoped to Al doped ZnO thin films prepared by using ethanol solution. However, for the methanol solution; the electrical conductivity of the film is stabilized after doping.     

一种生物柴油代用品在HZSM-5分子筛催化剂上的催化热解

为了深入了解生物柴油在ZSM-5沸石上的催化反应机理,在常压的流动反应器中进行了生物柴油代用品丁酸甲酯在氢型ZSM-5(HZSM-5)催化剂上的热解和催化热解. 热解产物使用气相色谱-质谱法定性和定量测量. 动力学模型和实验表明,气相中氢提取反应是热解过程中丁酸甲酯分解的主要途径,但在HZSM-5上,丁酸甲酯则主要通过解离生成烯酮和甲醇消耗;与无催化反应相比,丁酸甲酯在HZSM-5上的初始分解温度降低了约300 K. 并且通过Arrhenius方程获得了在催化热解和均相热解条件下丁酸甲酯消耗的表观活化能. 明显降低的表观活化能证实了HZSM-5对丁酸甲酯热解的催化性能. 此外催化剂的活化温度对HZSM-5的某些催化性能具有一定的影响. 该研究对进一步的实际生物柴油燃料的催化燃烧具有一定的指导意义.     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

Emulsion Combustion and Flame Spray Synthesis of Zinc Oxide/Silica Particles

Two flame spray methods, emulsion combustion method (ECM) and flame spray pyrolysis (FSP), were compared for synthesis of pure and mixed SiO₂ and ZnO nanoparticles. The effect of silicon precursor was investigated using liquid hexamethyldisiloxane (HMDSO) or SiO₂ sol, while for ZnO zinc acetate (ZA) was used. Gas phase reaction took place when using HMDSO as Si precursor, forming nanoparticles, whereas the SiO₂ sol used as Si source was not evaporated in the flame, creating large aggregates of the sol particles (e.g. 1 m). The FSP of ZA produced ZnO homogeneous nanoparticles. Lower flame temperatures in ECM than in FSP resulted in mixed gas and liquid phase reaction, forming ZnO particles with inhomogeneous sizes. The FSP of HMDSO and ZA led to intimate gas-phase mixing of Zn and Si, suppressing each other's particle growth, forming nanoparticles of 19 nm in BET-equivalent average primary particle diameter. Nucleation of ZnO and SiO₂ occurred independently by ECM of HMDSO and ZA as well as by FSP of the SiO₂ sol and ZA, creating a ZnO and SiO₂ mixture. The reaction of ZnO with SiO₂ was likely to be enhanced by ECM of the SiO₂ sol and ZA where both Zn and Si species were not evaporated completely, resulting in ZnO, -willemite and Zn_1.7SiO₄ mixed phase.     

硼碳氮纳米管的热解法制备及生长机理研究

以乙二胺、二茂铁和硼氢化钠为原料,以N2和H2为辅气,用钴作催化剂,在不同温度下制备出了具有竹节状结构的硼碳氮(BCN)纳米管.根据透射电子显微镜观察,分析了BCN纳米管的生长机理.B和N的同时掺杂,所形成的五边形结构比单独N掺杂时具有更低的形成能,是竹节状结构形成的主要原因.用Raman光谱可以用来表征BCN纳米管中B和N的掺杂程度及纳米管的质量.分析表明,在860℃下制备的BCN纳米管竹节状结构最密集,质量最好,产率最高.扫描俄歇微探针分析表明,在860℃下制备的BCN纳米管的元素组成比为B∶N∶C= 关键词： BCN纳米管 热解 透射电子显微镜 Raman光谱     

Suspension plasma sprayed composite coating using amorphous powder feedstock

Al₂O₃-ZrO₂ composite coatings were deposited by the suspension plasma spray process using molecularly mixed amorphous powders. X-ray diffraction (XRD) analysis shows that the as-sprayed coating is composed of α-Al₂O₃ and tetragonal ZrO₂ phases with grain sizes of 26 nm and 18 nm, respectively. The as-sprayed coating has 93% density with a hardness of 9.9 GPa. Heat treatment of the as-sprayed coating reveals that the Al₂O₃ and ZrO₂ phases are homogeneously distributed in the composite coating.     

Thermal stability of ester linkage in the presence of 1,2,3‐Triazole moiety generated by click reaction

The copper(I)‐catalyzed alkyne‐azide cycloaddition (CuAAC), so‐called “click” reaction, is one of most useful synthetic strategies to connect two polymer chains. 1,2,3‐Triazole ring (TA) produced by the click reaction has good thermal and chemical stability. However, we observed that block copolymers synthesized by the click reaction showed thermal degradation to give homopolymers when they are thermally annealed at high temperature, which is required for obtaining equilibrium microdomain structure. To investigate the origin of thermal instability of block copolymers, we synthesized model polystyrenes (PSs) using systematically designed bi‐functional atom transfer radical polymerization (ATRP) initiators containing TA. PS including both ester and TA groups showed thermal decomposition at relatively low temperature (e.g., 140 °C). MALDI‐TOF analysis clearly demonstrated that the cleavage site is the ester group adjacent to TA. We also found that the bromine group located at the polymer chain end plays an important role in pyrolysis of ester groups at low temperature. The pyrolysis occurs by syn‐elimination of the ester group. This result implies that the phase behavior of block copolymer synthesized by click reaction should be carefully investigated when high temperature thermal annealing is required. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 427–436     

在轴向气流作用下液体轴对称抛撒二次破碎的实验研究

液体轴对称抛撒的实验研究是以云雾爆轰武器的研制为背景的。为了研究轴向气流作用下液体轴对称抛撒二次破碎所形成的雾化场特性,本文利用两台激波管并对之加以改造,成功地在实验室实现了轴向气流作用下液体的轴对称抛撒。为了研究其雾化场的远场特性,本文利用激光粒子测量仪获得了在不同实验工况和不同位置下的雾化场SMD分布曲线。实验数据表明,由于轴向气流速度的增加,液体破碎的Weber数得到了提高,导致二次破碎初期雾化场的SMD随之减小;随着抛撒驱动压力的提高,二次破碎初期雾化场的SMD也随之减小;在同一工况下,雾化场SMD随着测量位置与喷口距离的增加而变大。     

丙烯酸盐喷膜防水材料在酸碱浸润和冻融循环条件下的耐久性试验分析

丙烯酸盐喷膜防水材料在酸碱溶液浸润和冻融条件下的耐久性能是该类材料在工程应用中较难回避的实际问题,论文采用酸性介质(0.2%的H2SO4溶液)和碱性介质(0.1%NaOH+饱和Ca(OH)2溶液)对该材料进行饱和浸泡并进行冻融循环后,研究了该材料的吸水性、断裂拉伸强度和拉断伸长率的变化规律。试验结果表明:喷膜防水材料在侵蚀-冻融循环作用下,其拉断伸长率和断裂拉伸强度显著降低,且酸性介质对材料拉伸性能的影响较大;材料耐低温冰冻能力较强,耐高温能力较差。反映出丙烯酸盐喷膜防水材料在低温冰冻和碱性介质中耐久性较好,不建议在高温和酸性介质条件下使用。