Production of carbon soot with a high content of C60 and C70 fullerenes by electric arc

The effect of the parameters of the electric arc (helium pressure, current and voltage, clearance between electrodes) and of the peculiarities of the setup design (arrangement of electrodes, distance between the arc and the cooling surface, temperature of the soot condensation surface) on the yield of fullerenes has been studied. Conditions for producing soot with a C₆₀ and C₇₀ content up to 43% (toluene extract) have been found.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 805–809, May, 1994.The authors are grateful to N. G. Spitsyna and A. V. Dubovitskii for the determination of the content of C₆₀ and C₇₀ fullerenes in the extract.The work was financially supported by the Russian Foundation for Basic Research (Project 93-03-18705).     

变频压缩机空调系统的理论分析及实验研究

变频空调器是由变频压缩机驱动的空调系统,压缩机通过变频调节其转速使压缩机单位时间内的排气量变化,从而达到调节制冷量的目的。本文提出了变频空调器制冷系统的原理和设计方法,具体给出了制冷量和压缩机频率的关系方程,并从理论和实验两方面对变频空调器制冷系统进行了分析,得到了频率曲线图,为变频空调器制冷系统的设计提供了依据。     

Slow quenching for a one-dimensional kinetic Ising model: Residual energy and domain growth

A one-dimensional kinetic Ising model with Glauber dynamics subjected to a slow continuous quench to zero temperature is studied. For a rather general class of cooling schemes, described by a time-dependent temperatureT(t), the mean domain sizeL(t) is calculated along with the residual energye _res (r) as a function of the cooling rater. If the attempt frequency =₀ exp(–/kT), entering into the transition rates, is temperature dependent (i.e., the barrier is non-zero), the asymptotic growth ofL(t) is given byL()–L(t)~exp[–/kT(t)]. For this case the residual energy exhibits a power-law behaviore _res(r) ~r ^{/2(1 + )} forr small, where =4J/ andJ is the nearest neighbor coupling constant. For =0 and for certain cooling schemes the residual energy is zero andL(t)~t1/2, independent ofr.     

Measurement and modeling of the glass transition temperatures of multi-component solutions

Protein crystals are usually grown in multi-component aqueous solutions containing salts, buffers and other additives. To measure the X-ray diffraction data of the crystal, crystals are rapidly lowered to cryogenic temperatures. On flash cooling, ice frequently forms affecting the integrity of the sample. In order to eliminate this effect, substances called cryoprotectants are added to produce a glassy (vitrified) state rather than ice. Heretofore, the quantity of cryoprotectant needed to vitrify the sample has largely been established by trial and error. In this study, differential scanning calorimetry (DSC) was used to measure the melting (T_m), devitrification (T_d) and glass transition (T_g) temperatures of solutions with a range of compositions typical of those used for growing protein crystals, with the addition of glycerol as cryoprotectant. The addition of cryoprotectant raises the T_g and lowers the T_m of bulk solution thereby decreasing the cooling rates required for vitrification of protein crystals. The theoretical T_g value was calculated using the apparent volume fraction using the Miller/Fox equation extended for multi-component systems. The experimental values of T_g were within approximately ±4% of that predicted by the model. Thus, the use of the model holds the promise of a rational method for the theoretical determination of the composition of cryoprotectant requirement of protein crystallization solutions.     

Residual stress and deformation during rapid cooling process in an epoxy plate

Residual stress in the epoxy plate during a rapid cooling process was measured by the layer removal method and calculated by the linear thermoviscoelastic theory considering specific volume relaxation. The relaxations of the tensile modulus and specific volume were measured by an Instron thermomechanical analyzer. When the starting temperature of the cooling process was near the glass transition temperature of the cured epoxy, the residual stress in the epoxy plate was smaller than when the starting temperature was higher than the glass transition temperature. However, the transient stress in the cured epoxy plate was higher when the starting temperature was near the glass transition temperature than when the starting temperature was higher than the glass transition temperature. The quenched epoxy plate was compressed in the direction parallel to the surface and expanded in the thickness direction.     

主动冷却点阵夹层防热结构温度响应计算模型北大核心CSCD

针对点阵夹层结构主动热防护问题,建立了夹层结构面板和芯体导热与冷却剂对流耦合的非稳态传热理论模型,利用有限体积法离散控制方程并在MATLAB中进行了迭代求解.模型首次考虑了面板与夹芯杆之间的收缩热阻,并利用分离变量法得到了收缩热阻的近似解析解.基于单胞模型和周期性边界条件,模拟得到了模型所需的表面对流传热系数h_(b)和h_(fin).最后,选取多单胞计算工况进行数值模拟和理论模型对比,并讨论了收缩热阻对模型预测精度的影响.结果表明:理论模型能够准确预测夹层结构及内部流体的温度变化,理论与仿真之间的最大误差不超过1%;随着外加热流密度不断增大,忽略收缩热阻使得计算结果造成的误差不断增大;与数值模拟相比,理论模型可显著地减少计算时间并节省计算资源,尤其适用于非均匀、非稳态复杂热载荷下点阵夹层结构的温度响应计算.     

Evaluation of the calibration errors on cooling of a differential scanning calorimeter using different sets of standard metals

The temperature calibration on cooling of thermal analysis instruments is important for the accurate study of the non-isothermal crystallization kinetics of semi-crystalline polymers. In previous works, a methodology was proposed for performing the calibration on cooling of differential scanning calorimeters (DSCs) with standard metals, and the calibration errors were checked using transitions of high-purity liquid crystals. In this work, alternative, physically meaningful, procedures for carrying out the calibration on cooling are analyzed and validated. The calibration errors are evaluated also with liquid crystalline transitions, when the calibration is performed with standard metals, in a wide temperature range, and when due account is taken for the need of isothermal corrections to the temperature measurements. It is shown that any pair of standard metals may be used to calibrate on cooling, that the calibration errors increase for wider working temperature ranges and that, providing that certain conditions are fulfilled, both calibration procedures yield similar results.     

Technological quality determination of pharmaceutical disintegrant by DSC cooling and DSC photovisual

A number of disintegrants are available on the market. They improve tablets’ disintegration. The objective of this work is the comparison of the technological quality parameters of disintegrants using different analytical techniques. Three batches of disintegrants and their binary mixtures (water:disintegrants) were investigated. Cooling experiments were used from –30 up to 200°C. The data obtained showed calorimetric differences between the samples. In the binary mixtures water showed different crystallization behaviour from the one found in the literature. According to the results DSC technique helped the quality control of different disintegrants.     

Fouling Mitigation in a Heat Exchanger: High Cycles of Concentration for a Cooling-Tower Application

The purpose of the present study is to investigate the effect of a physical water treatment (PWT) technology on fouling mitigation in a simulated cooling tower operating at high cycles of concentration. Hard water was produced by evaporating pure water in a circulating open cooling tower, where dissolved calcium carbonate ions became concentrated with time. Heat transfer tests were conducted in a rectangular channel by varying the cycle of concentration (COC) from 5 to 10, and fouling resistances were measured over 270 hrs for each case with and without the PWT treatment. Another test was conducted with no blowdown case with and without the PWT treatment. The fouling resistance at 5 cycles with the PWT treatment was about 70% less than that in the case without the PWT treatment at the end of 270-hr tests. Even at 10 cycles, the PWT treatment reduced the fouling resistance by 60% from the value for the no treatment case. Thus, one can conclude that the PWT technology can help circulating cooling-tower water at relatively high COC for significant freshwater conservation, while keeping fouling resistances below industry standards.