三量子位Heisenberg XX 链中杂质对纠缠的影响

研究了有杂质时三量子位Heisenberg-XX链中正常格点之间的热纠缠情况，给出了Concurrence的解析表达式.进一步的讨论发现，杂质对正常格点的热纠缠有着重要的影响，甚至能够改变纠缠在反铁磁区的特性.理论表明，可以通过调节温度和杂质参数来控制纠缠. 关键词： Heisenberg -XX链 热纠缠 杂质格点     

板状激光振荡介质温度场和应力场的数值模拟

以非均匀内热源模型为基础,并考虑材料的导热系数和热膨胀系数的温度相关性,利用有限元方法,对板状激光振荡介质在不同功率和冷却强度下的温度和热应力分布进行了数值模拟及分析。根据计算结果提出了最大有效换热系数的概念,指出换热系数超过最大有效换热系数后,继续强化传热对减小高功率激光器的热效应已无明显效果。以此得出采用常规冷却技术所允许的最大泵浦加热功率。     

免疫珠技术快速检测腹泻性大肠杆菌

采用表面光滑玻璃珠作为载体材料，用1：40的腹泻性大肠杆菌诊断血清进行包被。可制成免疫珠。这种免疫珠能与腹泻性大肠杆菌发生特异性结合。经乳糖蛋白胨培养液培养，然后根据其产酸产气进行判断。能在18h内完成腹泻性大肠杆菌的检测。其灵敏度为样液中含有腹泻性大肠杆菌数必须大于10CFu／mL．该法简单、快速、易操作、灵敏度高。     

Thermal Equilibrium Between Radiation and Matter

In 1916, Einstein rederived the blackbody radiation law of Planck that originated the idea of quantized energy one hundred years ago. For this purpose, Einstein introduced the concept of transition probability, which had a profound influence on the development of quantum theory. In this article, we adopt Einstein's assumptions with two exceptions and seek the statistical condition for the thermal equilibrium of matter without referring to the inner details of either statistical thermodynamics or quantum theory. It is shown that the conditions of thermodynamic equilibrium of electromagnetic radiation and the energy balance of thermal radiation by the matter, between any of its two energy-states, not only result in Planck's radiation law and the Bohr frequency condition, but they remarkably yield the law of the statistical thermal equilibrium of matter: the Maxwell–Boltzmann distribution. Since the transition probabilities of the modern quantum theory of radiation coincide with their definition in Einstein's theory of blackbody radiation, the presented deduction of the Maxwell–Boltzmann distribution is equally valid within the bounds of modern quantum theory. Consequently, within the framework of the fundamental assumptions, the Maxwell–Boltzmann distribution of energy-states is not only a sufficient, but a necessary condition for thermal equilibrium between the matter and radiation.     

Lanthanum nitrate decomposition by both temperature programmed heating and citrate gel combustion

Thermal decomposition of lanthanum nitrate to lanthanum oxide was carried out by both temperature programmed heating (TPH) and citrate-gel combustion. The temperature programmed heating was carried out under flow of oxidizing (air), neutral (nitrogen) and reducing (25 vol.% hydrogen+argone mixture) gases, and the processes were controlled by simultaneous thermogravimetry and differential thermal analysis. It was shown that hydrogen atmosphere helps to reduce temperatures of all decomposition steps. The results of TPH were utilized to check the nature of residues in the products of lanthanum nitrate-to-oxide conversion performed via citrate-gel combustion technique.     

Investigating laser rapid manufacturing for Inconel-625 components

This paper presents an investigation of laser rapid manufacturing (LRM) for Inconel-625 components. LRM is an upcoming rapid manufacturing technology, it is similar to laser cladding at process level with different end applications. In general, laser-cladding technique is used to deposit materials on the substrate either to improve the surface properties or to refurbish the worn out parts, while LRM is capable of near-net shaping the components by layer-by-layer deposition of the material directly from CAD model. In the present study, a high-power continuous wave (CW) CO₂ laser system, integrated with a co-axial powder-feeding system and a three-axis workstation were used. The effect of processing parameters during LRM of Inconel-625 was studied and the optimum set of parameters for the maximum deposition rate was established employing Orthogonal L9 array of Taguchi technique. Results indicated that the powder feed rate and the scan speed contributed about 56% and 26%, respectively to the deposition rate, while the influence of laser power was limited to 10% only. Fabricated components were subjected to non-destructive testing (like—ultrasonic testing, dye-penetrant testing), tensile testing, impact testing, metallographic examinations and micro-hardness measurement. The test results revealed defect-free material deposition with improved mechanical strength without sacrificing the ductility.     

Specific heat and related thermophysical properties of liquid Fe-Cu-Mo alloy

The specific heat and related thermophysical properties of liquid Fe77.5Cu13Mo9.5 monotectic alloy were investigated by an electromagnetic levitation drop calorimeter over a wide temperature range from 1482 to 1818 K. A maximum undercooling of 221 K (0.13 Tm) was achieved and the specific heat was determined as 44.71 J·mol-1·K-1. The excess specific heat, enthalpy change, entropy change and Gibbs free energy difference of this alloy were calculated on the basis of experimental results. It was found that the calculated results by traditional estimating methods can only describe the solidification process under low undercooling conditions. Only the experimental results can reflect the reality under high undercooling conditions. Meanwhile, the thermal diffusivity, thermal conductivity, and sound speed were derived from the present experimental results. Furthermore, the solidified microstructural morphology was examined, which consists of (Fe) and (Cu) phases. The calculated interface energy was applied to exploring the correlation between competitive nucleation and solidification microstructure within monotectic alloy.     

Molecular flow and wall collision age distributions

The use of storage cells has become a standard technique for internal gas targets in conjunction with high energy storage rings. In case of spin-polarized hydrogen and deuterium gas targets the interaction of the injected atoms with the walls of the storage cell can lead to depolarization and recombination. Thus the number of wall collisions of the atoms in the target gas is important for modeling the processes of spin relaxation and recombination. It is shown in this article that the diffusion process of rarefied gases in long tubes or storage cells can be described with the help of the one-dimensional diffusion equation. Mathematical methods are presented that allow one to calculate collision age distributions (CAD) and their moments analytically. These methods provide a better understanding of the different aspects of diffusion than Monte Carlo calculations. Additionally it is shown that measurements of the atomic density or polarization of a gas sample taken from the center of the tube allow one to determine the possible range of the corresponding density weighted average values along the tube. The calculations are applied to the storage cell geometry of the HERMES internal polarized hydrogen and deuterium gas target. Received 9 July 2001 and Received in final form 18 September 2001     

复合多层介质在可变温度和集中荷载作用下的位移和应力

研究了多层介质中的热弹性位移和应力.多层介质具有不同厚度,各层又具有不同的弹性性质,最上层表面上作用热荷载和集中荷载.假设各层分别是均匀、各向同性弹性材料,各层相关的位移分量是轴对称的,对称轴为各层表面的垂线.因此,各层应力函数满足无体力的单一方程.利用积分变换法求解了该方程,对由任意多个层数构造的多层介质,给出了其相应层数基础热弹性位移和应力的解析表达式.并对3层介质和4层介质时的数值结果进行了比较.     

热动力学问题的数值计算

 对含热传导的流体动力学方程组，用有限元方法进行数值求解。采用傅里叶热传导计算热流、用热流连续条件计算单元间接触面的温度、用三角形传热法计算体单元表面的热流，考虑各向同性弹塑性流体材料模型、三项式物态方程和导热系数与状态的相关性，给出了傅里叶热传导、接触传热、热应力应变效应、以及混合物冲击压缩特性等算例。对混合物冲击温度的数值模拟表明，小颗粒混合物在冲击压缩过程中，颗粒间的温度有差别、稍有波动，并随时间趋向于一致，以至热平衡。