气相-质谱法测定粮谷中恶草酮的残留量

 应用微量化学法和固相萃取技术 ,建立了粮谷中恶草酮残留量的气相 质谱 (GC MS)测定方法。用苯 正己烷 (体积比为 1∶1)萃取 ,中性氧化铝小柱净化。净化液用GC MS测定 ,采用外标法定量。恶草酮在大米中的回收率为 90 4%～ 115 .7% ,RSD为 2 %～ 6 % ,在玉米中的回收率为 81 3%～ 10 9 7% ,RSD为 4%～ 9% ,最低定量检出限为 0 0 0 5mg/kg。该法快速、灵敏、准确 ,各项技术指标均满足农药残留检测的要求。     

Liquid–solid disk extraction followed by supercritical fluid elution and gas chromatography of phenols from water

A method combining the techniques of liquid – solid disk extraction (LSDE) and supercritical fluid elution (SFE) has been developed for the phenols regulated by the Clean Water Act. LSDE uses a disk or membrane made of polytetrafluoroethylene (PTFE) fibrils impregnated with small particles, e.g. styrene divinylbenzene (SDB) resin, to extract phenols from water. After disk extraction the retained analytes are eluted from the disk using SFE. SFE is used as an alternative to liquid solvent elution with an organic solvent. Analytes are separated, identified, and quantified using gas chromatography – ion trap detector mass spectrometry (GC-ITDMS). The method is capable of sub parts per billion detection limits, and precision of 5–28% RSD. Evaluation of various disks or membranes, such as C₁₈-silica disks, SDB disks, and ion exchange membranes, has also been performed for the extraction of phenols from water. The results obtained from the in-situ aqueous acetylation of phenols and extraction of their acetates are quantitative. The utilization of LSDE and SFE techniques has proven to be a more effective approach than liquid – liquid extraction in minimizing air pollution and solvent waste.     

羟基铝溶液及铝交联蒙脱土的研究

本文用(27)~Al NMR法和8-羟基喹啉萃取法分别研究了羟基铝溶液中十三聚铝含量的变化规律,还用X-射线衍射法研究了铝交联蒙脱土d_(001)的变化。研究结果表明,铝离子的聚合情况主要由羟铝比决定,而浓度影响不大。随着羟铝比的增加,溶液中单核铝离子含量减少,十三聚铝离子相对含量增加,所得铝交联蒙脱土的d_(001)也随之增大。参照这些变化规律、控制羟基铝溶液的组成,可以制备各种层柱状铝交联蒙脱土复合物。     

Pressurized hot water extraction of berberine, baicalein and glycyrrhizin in medicinal plants

Pressurized hot water extraction (PHWE) using a laboratory made system was applied for the extraction of thermally labile and reasonably polar components such as berberine in coptidis rhizoma, glycyrrhizin in radix glycyrrhizae/liquorice and baicalein in scutellariae radix. PHWE was carried out dynamically at a flow of 1 ml/min, temperature between 95 and 140 °C, an applied pressure of 10-20 bar and extraction time of 40 min. Extraction by PHWE was found to give efficiencies comparable to Soxhlet extraction for baicalein in scutellariae radix and sonication for berberine in coptidis rhizoma, and glycyrrhizin in radix glycyrrhizae. Effects of ethanol added into the water used in PHWE were explored. Pressurized liquid extraction (PLE) with methanol as solvent was used for extraction of baicalein in scutellariae radix. The marker compounds present in the various medicinal plant extracts were determined by gradient elution HPLC.     

Spectral regions selection to improve prediction ability of PLS models by changeable size moving window partial least squares and searching combination moving window partial least squares

Changeable size moving window partial least squares (CSMWPLS) and searching combination moving window partial least squares (SCMWPLS) are proposed to search for an optimized spectral interval and an optimized combination of spectral regions from informative regions obtained by a previously proposed spectral interval selection method, moving window partial least squares (MWPLSR) [Anal. Chem. 74 (2002) 3555]. The utilization of informative regions aims to construct better PLS models than those based on the whole spectral points. The purpose of CSMWPLS and SCMWPLS is to optimize the informative regions and their combination to further improve the prediction ability of the PLS models. The results of their application to an open-path (OP)/FT-IR spectra data set show that the proposed methods, especially SCMWPLS can find out an optimized combination, with which one can improve, often significantly, the performance of the corresponding PLS model, in terms of low prediction error, root mean square error of prediction (RMSEP) with the reasonable latent variable (LVs) number, comparing with the results obtained using whole spectra or direct combination of informative regions for a compound. Regions consisting of the combinations obtained can easily be explained by the existence of IR absorption bands in those spectral regions.     

High-performance liquid chromatographic determination of Levetiracetam in human plasma: comparison of different sample clean-up procedures

An accurate and precise high-performance liquid chromatographic method using diode array detection for the determination of the novel antiepileptic, Levetiracetam, has been developed. Three clean-up procedures for the analysis of Levetiracetam in human plasma were implemented and evaluated, namely solid-phase extraction, deproteinization by addition of organic solvents and formation of insoluble salts. Adenosine was used as the internal standard for all three sample pretreatment procedures. Among the several cartridges used for solid-phase extraction, the hydrophilic-lypophilic balance (Oasis) HLB) phase provides the best extraction yield of Levetiracetam, together with high precision. With the two other clean-up procedures involving plasma deproteinization by addition of methanol or zinc sulphate, lower sensitivity and precision of the assays were obtained. However, they are cheaper and faster when compared with the solid-phase extraction procedure.     

Analytical procedures for quantification of peptides in pharmaceutical research by liquid chromatography–mass spectrometry

Peptide quantification by liquid chromatography–mass spectrometry (LC–MS) combines the high resolving power of reversed-phase (RP) chromatography with the excellent selectivity and sensitivity of mass spectrometric detection. On the basis of comprehensive practical experience in the analysis of small molecules, pharmaceutical research is developing technologies for analysis of a growing number of peptidic drug candidates. This article is a detailed review of procedures based on LC–MS techniques for quantitative determination of peptides. With the focus on pharmaceutical applications several technologies for sample preparation, various aspects of peptide chromatography, important characteristics of ESI–MS, selectivity of MS-detection modes, the large variability of internal standards, and modern instrumentation are discussed. The demand for reliable, robust, sensitive, and accurate methods is discussed using numerous examples from the literature, complemented by experiments and results from our laboratory.     

Spectrophotometry Determination of Cobalt after Extraction of its Ternary Complex with 3-(4-Phenyl-2-Pyridyl)-5,6-Diphenyl-1,2,4-Triazine and Tetraphenylborate into Molten Naphthalene

The reaction of 3-(4-phenyl-2-pyridyl)-5,6-diphenyl-1,2,4-triazine (PPDT) and tetraphenylborate (TPB) with cobalt (II) has been studied to determine the optimum conditions for the extraction and quantitative spectrophotometry determination of this metal. The ternary complex is extracted into molten naphthalene at pH 3.6–7.4. The solid naphthalene containing the cobalt associated complex is separated by filtration and dissolved in acetonitrile. Beer's law is obeyed in the concentration range 8–140 μg cobalt in 10 ml of acetonitrile solution. The molar absorptivity and sensitivity are 4.2×10³ l·mol^?1·cm^?1 and 0.01408 μg/cm², respectively. The other factors such as pH, amounts of reagents and naphthalene, shaking and standing times, and the effect of diverse ions are studied. The method has been applied to the determination of cobalt in iron steel alloys.     

Comparison of adsorbents for on-line solid-phase extraction of polycyclic aromatic hydrocarbons before liquid chromatography with UV detection

Summary On-line solid-phase extraction (SPE) coupled with reversed-phase liquid chromatography and UV detection at 254 nm has been used for the determination of trace-level polycyclic aromatic hydrocarbons (PAH) in soil extracts. Five commercially available adsorbents (C₈, C₁₈, PLRP-S, PRP-1, and Bond-Elut Env) were evaluated. Results showed that recovery of the PAH decreased with increasing molecular weight, because of their poorer solubility. Recovery of high-molecular-weight PAH was significantly improved by addition of 10% (v/v) acetonitrile to the sample before loading of the SPE adsorbent. PAH recovery ranged from 64.0 to 108% when a 50 mL sample spiked with 1 μg L⁻¹ was applied to these adsorbents. Determination of PAH was possible with detection limits below 0.05 μg L⁻¹, which corresponds to 0.2 μg kg⁻¹ soil. The method was successfully used to determine PAH in soil extracts.