Measurement and prediction of solubilities and diffusion coefficients of carbon dioxide in starch–water mixtures at elevated pressures

The solubility and diffusion coefficient of carbon dioxide in intermediate‐moisture starch–water mixtures were determined both experimentally and theoretically at elevated pressures up to 16 MPa at 50 °C. A high‐pressure decay sorption system was assembled to measure the equilibrium CO₂ mass uptake by the starch–water system. The experimentally measured solubilities accounted for the estimated swollen volume by Sanchez–Lacombe equation of state (S‐L EOS) were found to increase almost linearly with pressure, yielding 4.0 g CO₂/g starch–water system at 16 MPa. Moreover, CO₂ solubilities above 5 MPa displayed a solubility increase, which was not contributed by the water fraction in the starch–water mixture. The solubilities, however, showed no dependence on the degree of gelatinization (DG) of starch. The diffusion coefficient of CO₂ was found to increase with concentration of dissolved CO₂, which is pressure‐dependent, and decrease with increasing DG in the range of 50–100%. A free‐volume‐based diffusion model proposed by Areerat was employed to predict the CO₂ diffusivity in terms of pressure, temperature, and the concentration of dissolved CO₂. S‐L EOS was once more used to determine the specific free volume of the mixture system. The predicted diffusion coefficients showed to correlate well with the measured values for all starch–water mixtures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 607–621, 2006     

Characterization and electrical properties of polypyrrole/multiwalled carbon nanotube composites synthesized by in situ chemical oxidative polymerization

This study describes the preparation of polypyrrole (PPy)/multiwalled carbon nanotube (MWNT) composites by in situ chemical oxidative polymerization. Various ratios of MWNTs, which served as hard templates, were first dispersed in aqueous solutions with the surfactant cetyltrimethylammonium bromide to form micelle/MWNT templates and overcome the difficulty of MWNTs dispersing into insoluble solutions of pyrrole monomer, and PPy was then synthesized via in situ chemical oxidative polymerization on the surface of the templates. Raman spectroscopy, Fourier transform infrared (FTIR), field‐emission scanning electron microscopy (FESEM), and high‐resolution transmission electron microscopy (HRTEM) were used to characterize the structure and morphology of the fabricated composites. Structural analysis using FESEM and HRTEM showed that the PPy/MWNT composites were core (MWNT)–shell (PPy) tubular structures. Raman and FTIR spectra of the composites were almost identical to those of PPy, supporting the idea that MWNTs served as the core in the formation of a coaxial nanostructure for the composites. The conductivities of these PPy/MWNT composites were about 150% higher than those of PPy without MWNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1413–1418, 2006     

Preparation and characterization of activated carbons from impregnation pitch by ZnCl2

Using an impregnation pitch from bituminous coal tar (OP) supplied by Industrias Químicas del Nalon Company as raw material, two phases (isotropic and anisotropic) have been obtained. The latter was used as precursor for the preparation of activated carbons. First, a chemical activation process was carried out with ZnCl₂ as activating agent. The process was conducted at different concentrations and temperatures and by means of impregnation with solid zinc chloride. Optimal values were obtained for samples prepared by using a ZnCl₂:pitch ratio equal to 3:1 (sample AZn3). Next, this sample was thermally treated at two different temperatures, i.e., 700 and 800 °C. A lose of specific surface area, microporosity and mesoporosity was observed with respect to sample AZn3, such a lose being more remarkable as temperature increased. Moreover, impregnation of the anisotropic phase of the original pitch with an aqueous solution of ZnCl₂ followed by thermal treatment resulted in a poorly developed surface area and porous texture, probably due to the presence of Zn complexes, which interfere with the activation process.     

Differential Pulse Polarographic Determination of Nitrate in AUT Solution

A differential pulse polarographic method for the determination of nitrate ion has been developed. With 0.5 M CaCl₂ as supporting electrolyte, NO^?₃ is reduced to give a peak with E_1/2=–1.836 Volt vs. the Ag/AgCl electrode. The differential pulse polarographic peak height is proportional to the nitrate concentration from 20 to 60 ppm. The detection limit for nitrate is 2 ppm in pure aqueous solution. In the determination of 40 ppm nitrate a relative precision (relative standard deviation) of less than 2% was achieved. Nitrite interferes seriously and should be absent if accurate results are required. The method has been applied to the determination of nitrate in Ammonium Uranyl Tricarbonate (AUT) Solution, results obtained by this method are compared to those obtained by ion chromatography. The agreement between the two sets of results suggests that the DPP method can be used with a fair degree of confidence.     

气密性碳涂覆光纤筛选强度与电阻关系研究

通过实验分析确立了把光纤电阻作为衡量气密性碳涂覆光纤通过２％应变筛选的过渡标准。要拉制２％应变筛选的碳涂覆光纤，其电阻值应小于３０ｋΩ／ｃｍ。     

Gas transport through homogeneous and asymmetric polyethersulfone membranes

Both homogeneous and asymmetric polyethersulfone (PES) membranes were prepared by solvent casting. The sorption and permeation behavior of CO₂, O₂, and N₂ using these two kinds of cast PES membranes and commercially available homogeneous PES film was investigated to extract the pressure dependence of gas permeability and the permselectivity for CO₂ relative to N₂, and to confirm the validity of the working assumption that a skin layer in an asymmetric membrane can be essentially replaced by a thick homogeneous dense membrane. The pressure dependence of the mean permeability coefficient to CO₂ in homogeneous membranes obeys the dual-mode mobility model. The ideal separation factor for CO₂ relative to N₂ at an upstream pressure of 0.5 MPa attains ca. 40, while the permeability to CO₂ is about 2.7 Barrer at the same upstream pressure. The same separation factor in asymmetric membranes amounts to 35. The diffusion behavior for the skin layer in an asymmetric membrane with a thin skin layer can be simulated approximately by that in a homogeneous dense membrane. © 1993 John Wiley & Sons, Inc.     

活性炭酸处理对CuO／C催化剂上NO还原反应的影响

４种国产活性炭被用于ＮＯ还原反应，其中，山楂核炭和山桃核炭具有较高的ＮＯ还原转化率。实验发现，表面含氧基团－ＣＯＯ－对活性炭自身的还原性和对ＮＯ的还原活性有很重要的影响。对表面富－ＣＯＯ－基团的活性炭，稀盐酸处理使表面－ＣＯＯ－显著分解。     

助剂改性活性炭担载Pt催化剂催化硝基苯加氢制对氨基苯酚

以改性活性炭担载的Pt为催化剂催化硝基苯经加氢重排一步合成对氨基苯酚，收率54．70％，选择性可达91.40%。     

Carbon deposition on a Ni/α-Al2O3 catalyst

The kinetics of carbon deposition over a Ni/α-Al₂O₃ commercial catalyst, has been studied using CH₄−H₂ gas mixtures in the range of 748–873 K. A Hougen-Watson type model gives good agreement with the experimental rates.