8 mm回旋行波管和返波管的三折螺旋波纹波导色散分析

 三折螺旋波纹波导使TE11模和TE21模相互耦合，其色散曲线能够在宽频带内与电子回旋共振，因此需要对色散方程进行研究。提出了适合工程实用的行波模式和返波模式的色散方程，并对方程中的耦合系数进行了简化，误差在1%左右。利用CST软件的VBA语言对螺旋波纹波导进行建模和计算，根据模拟得到的传输特性曲线的特点，提出一种模拟方法，将模拟与理论计算得到的色散曲线作对比，误差在5%左右。     

光纤的能量传输特性及应用

着重分析了影响光纤传输能量以及光纤传输中造成能量损耗的因素。这些因素主要包括光纤材料、构造、光纤的折射率分布、光纤的长度和芯径、光纤的数值孔径和热效应以及耦合等。同时 ,结合激光二极管点火的实例 ,分析探讨了其背景和应用价值。结论是 :为了尽可能减少能量损耗、提高光纤输出的激光功率和激光功率密度 ,应当选取合适的激光工作波长、较小的光纤长度、较小的芯径和较小的数值孔径 ,应采用渐变折射率分布光纤 ,应减少弯曲与耦合     

Combined effect of PMD and PDL on four-wave-mixing-induced crosstalk in WDM system

We derive an explicit autocorrelation function (ACF) formula of state of polarization for a fiber transmission system with polarization mode dispersion (PMD) and polarization dependent loss (PDL), which is found to agree well with Monte Carlo simulation. Then we use the new ACF to investigate the combined effect of PMD and PDL on the polarization multiplexed scheme. We find the performance of the polarization multiplexed scheme can be deteriorated more severely than the case without PDL.     

Fiber torsion sensor demodulated by a high-birefringence fiber Bragg grating

A new high-birefringence (Hi-Bi) fiber torsion sensor demodulated by a Hi-Bi fiber Bragg grating (FBG) is proposed in this study. The twisted Hi-Bi fiber sensor characteristics are analyzed using the Jones matrix. The intensity ratio from two reflected Bragg wavelengths is associated with the twist angle of the measured Hi-Bi fiber. It is found that the twist angle resolution is estimated at around 0.3° under ±0.1 dB readout from an optical spectrum analyzer if the polarization state of the light source is stable. The advantages of this new torsion sensor are: (1) insensitivity to intensity variations from the light source, (2) insensitivity to the torsion gauge length, and (3) absolute measurement in the twist angle. However, the polarization state of light in the proposed method needs to be controlled, and any birefringence change in the twisted Hi-Bi fiber needs to be prevented.     

光纤光栅激光器激射波长的研究

一般认为，用光纤光栅作选频元件的光纤激光器，激射波长与光纤光栅中心反射波长一致，本文报道了不同的实验研究结果。通过细致的实验研究，发现光纤光栅激光器激射波长相对于光纤光栅中心反射波长有一定的偏移。激射波长可以出现在光栅中心反射波长的长波端，也可以出现在其短波端。对不同腔结构的掺镱、掺铒光纤光栅激光器的深入研究证明，谐振腔的各向异性对激光器的激射波长偏移起到决定性的作用，波长最大偏移量主要受限于光纤光栅的反射带宽。通过激光腔内的偏振控制器改变谐振腔的各向异性，可以在光纤光栅的反射带宽内控制激射波长的位置。     

用于机械振动实时监测的光纤光栅有源传感装置

把一对中心反射波长分别为1562.11nm和1562.71nm的光纤光栅粘贴在均质、等厚、等腰三角形悬臂梁上下表面作为环形腔光纤激光器端镜，当机械振动激励自由端时，通过观测激光输出脉冲，地施加于自由端的机械振动的频率进行了实时监测；观察两光栅波长漂移量差值的变化，可在0～6.1mm的范围内判断所测振动的振幅。低于100Hz时，实验结果与实际值基本吻合。     

OADM环网的实验研究

研究了光分插复用器(OADM)的关键技术,重点分析了相关的实现技术,完成了利用OADM构建全光环网的实验研究,给出了重要的实验数据,包括眼图、光谱图、光信噪比、保护与恢复等,并对这些实验数据进行了分析,为光传送网的设计与构建提供了重要的参考依据.     

光纤光栅的温度补偿

提出了一种简单、小型的光纤光栅温度补偿器件，将光纤光栅粘贴在具有负热膨胀系数的材料上，实现了光纤光栅的温度补偿。该器件在-20～44℃温度范围内光栅波长变化0.08m，是未补偿光纤光栅的1／8。     

锥形光纤间耦合特性的分析与检测

将通信光纤的末端拉制成锥形，利用光信号在光纤锥形区特有的传输和耦合特性，实现了光纤的耦合、连接和分束。用耦合模理论分析了锥形光纤间的传输和耦合性质，给出了光信号两锥形光纤间的耦合与两锥形光纤的距离和锥形区重叠长度等实验结果。     

Fiber-Optic Chemical Sensor for Detection of NO2 Using Poly (3-Octylthiophene)

A fiber-optic chemical sensor (FOCS) for detection of nitrogen dioxide (NO₂) molecules is reported. The FOCS presents an optropode structure because of the transmission properties of the sensitive material. The NO₂ FOCS is activated by using the semiconductor polymer: regioregular head-to-tail poly(3-octylthiophene-2,5-diyl). The operation wavelength of the sensor is 543.5 nm such that a simple LED and detector can be used for the design of this device. The sensor response decreases after each exposure, demonstrating the reduction in sensitivity as well as irreversibility lower than 5%. However, its properties such as rapid response, high selectivity, high sensitivity (0.43 ± 0.01 muW/ppm), hygroscopic properties, and its operation at room temperature make this kind of FOCS a good alternative for NO₂ toxic gas detection.