Amorphous Fe–Mg alloy thin films: magnetic properties and atomic vibrational dynamics

Amorphous (a-) Fe _x Mg_1?x alloys are interesting materials for the investigation of non-Debye-like low-energy vibrational excitations. We have prepared a-Fe _x Mg_1?x alloy thin films (0.3 ≤ × ≤0.7) by vapour quenching. The amorphous state was confirmed by conversion electron Mössbauer spectroscopy between 4.2–300 K, and the x- and temperature-dependence of the isomer shift and hyperfine magnetic field was measured. For x= 0.6 and 0.7, magnetic ordering occurs below ~150 K. The atomic vibrational density of states, g(E), was determined by nuclear resonant inelastic scattering, providing clear evidence for the non-Debye-like low-energy vibrational excitations.     

Determination of the boiling point distribution of sulfur compounds in light cycle oil using GC with a flame photometric detector and pyrolyzer

A method has been developed to determine the boiling point distribution of sulfur compounds in light cycle oils (LCO'S). The method chosen for this analysis was GC with a flame photometric detector (FPD) and pyrolyzer. Tests were carried out to evaluate the recovery efficiency, repeatability, and accuracy of the method. Repeatabilities within 2% were obtained. The recovery of benzothiophenes and dibenzothiophenes was close to 100%; this was important because these are the major sulfur components in LCO's. No hydrocarbon or solvent interferences were observed with the use of the pyrolyzer, even for a 95% solvent level. Comparison with results from other techniques showed that the method accurately determined the levels of sulfur compounds in the LCO boiling point range.     

Nitro musks in cosmetic products—determination by headspace solid-phase microextraction and gas chromatography with atomic-emission detection

Summary The combination of headspace solid-phase microextraction with atomic-emission detection enables highly selective and sensitive determination of itro musk compounds in cosmetic products. Sample preparation is considerably simplified; there is no solvent extraction step. Enrichment is influenced by the type and amount of cosmetic product investigated. The lowest amount giving well detectable peaks is 1 mg musk compound per kg sample. Calibration curves obtained from spiked solutions of selected reference cosmetics in water show very good linearity. Relative standard deviations of peak areas from repeated measurements are usually <10%. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

硅一体化薄膜微电极器件及其应用

提出用发展中的硅微机械加工技术设计制作硅一体化薄膜微电极器件．这类微电化学器件具有微电极所特有的全部优点，而且由于结构上的一体化，便于器件整体的微型化和集成化．试用薄膜微电极器件电流法常温直接检测ＣＯ２气体，取得了满意的结果。设想通过器件三维构型设计的改进和完善，器件工作的长期稳定性可望进一步提高．     

Flame Temperature Effect on the Structure of SiC Nanoparticles Grown by Laser Pyrolysis

Small SiC nanoparticles (10 nm diameter) have been grown in a flow reactor by CO₂ laser pyrolysis from a C₂H₂ and SiH₄ mixture. The laser radiation is strongly absorbed by SiH₄ vibration. The energy is transferred to the reactive medium and leads to the dissociation of molecules and the subsequent growth of the nanoparticles. The reaction happens with a flame. The purpose of the experiments reported in this paper is to limit the size of the growing particles to the nanometric scale for which specific properties are expected to appear. Therefore the effects of experimental parameters on the structure and chemical composition of nanoparticles have been investigated. For a given reactive mixture and gas velocity, the flame temperature is governed by the laser power. In this study, the temperature was varied from 875°C to 1100°C. The chemical analysis of the products indicate that their composition is a function of the temperature. For the same C/Si atomic ratio in the gaseous phase, the C/Si ratio in the powder increases from 0.7 at 875°C up to 1.02 at 1100°C, indicating a growth mechanism limited by C₂H₂ dissociation. As expected, X-ray diffraction has shown an improved crystallisation with increasing temperature. Transmission electron microscopy observations have revealed the formation of 10 nm grains for all values of laser power (or flame temperature). These grains appear amorphous at low temperature, whereas they contain an increasing number of nanocrystals (2 nm diameter) when the temperature increases. These results pave the way to a better control of the structure and chemical composition of laser synthesised SiC nanoparticles in the 10 nm range.     

高剂量率单次快脉冲辐射参量测量

记述了“强光一号”高剂量率脉冲辐射装置在状态调试过程中对其出射波形和辐射剂量进行监测的基本情况，实际监测的结果与设计方监测的结果进行了比对，双方的剂量监测值基本一致，偏差在20％以内；双方的波形形状十分相似，但测量得到的波形半宽度却相差10～20ns，最后对双方束流监测产生的差异进行了定性分析。     

Basic principles of technological shaping of optical properties and radiation hardness of PWO crystals

Technological conditions ensuring growth of optically homogeneous lead tungstate (PWO) crystals are reported. It is shown that the basic scintillator characteristics of PWO grown from highly purified raw material and properly doped with lanthanides are mainly determined by inclusions of oxides W_1−yL_yO_3−x (L=Y, La, Gd; 0<x<0.3). Moreover, surface-located inclusions with structure close to tungstenite may also be of importance. It is demonstrated that the scintillation properties can be intentionally designed by varying the oxygen content in the inclusions x and the surface structure. The optimal value for x and the most favorable surface structure are achieved by proper thermal regimes and environment content during the crystal annealing. The results enabled low-cost fabrication of PWO scintillators with steady and reproducible characteristics acceptable for the CERN project ALICE and ensured production of PWO on an industrial scale by “North Crystals” company at a rate of 125–135 crystals per year from every growth apparatus.     

Strong visible PL from the nc-Si thin film by Ni silicide mediated crystallization

We studied the growth of nanocrystalline silicon (nc-Si) thin film exhibiting a strong room temperature photoluminescence (PL) at 1.81–2.003 eV. The amorphous silicon was crystallized by Ni silicide mediated crystallization (Ni SMC) and then Secco-etched to exhibit the PL. The PL peak energy and intensity increase with increasing the metal density on the a-Si because of the reduction in the grain size down to 2 nm. The photoluminescence energy and peak intensity depend strongly on the Secco etch time because the grain size is reduced by etching the grain boundaries.     

Growth process of TiC clusters from Ti nanoparticles with evaporated carbon layer

Titanium carbide formation by the solid–solid reaction on the surface of Ti nanoparticles was studied in situ using a high-resolution transmission electron microscope with a heating stage. The cross-sectional image of the Ti surface was clearly observed. Vacuum-deposited carbon covered the whole the surface of Ti nanoparticles in spite of the partly evaporation on the nanoparticle surface. The diffusion of the carbon atoms inside the Ti nanoparticles depended on the size of the nanoparticles. When the Ti nanoparticle diameter was less than 30 nm, carbon atoms diffused into the Ti nanoparticle and formed TiC. The superstructure of the Ti nanoparticles was observed, which revealed the growth process of TiC to be the diffusion of carbon atoms. For Ti nanoparticles with diameter larger than 30 nm it was observed that diffusion of Ti atoms into the carbon layer was dominant, which resulted in formation of TiC in the carbon layer at the surface of Ti nanoparticles.