钙钛矿铁电纳米片诱导的P (VDF-TrFE)取向生长

Ferroelectric polymers are particularly attractive for applications in flexible electronic devices, and controlling its crystalline phase growth is crucial for obtaining optimized ferroelectric properties. Herein we report that a very low introduction (0.2% (w)) of single-domain ferroelectric PbTiO₃ nanoplates can effectively mediate the nucleation and subsequent growth of a crystalline phase within P (VDF-TrFE) (denoted by PVTF), forming highly oriented films and significantly improving the ferroelectric properties due to an alignment of the polarization directions of the polymer and the nanoplates.     

以构象概念为主线的高分子物理教学实践

提出以构象概念作为教学主线,论述了构象概念的意义以及构象概念与力学状态、橡胶弹性、取向态、流变性和凝聚态的内在关系。     

Orientation and structural development of semicrystalline poly(lactic acid) under uniaxial drawing assessed by infrared spectroscopy and X-ray diffraction

The effects of drawing temperature (T_d) and draw strain on the orientation and structure of semicrystalline poly(lactic acid) (PLA) films were investigated by wide angle X-ray diffraction and polarized Fourier transform infrared spectroscopy. Semicrystalline PLA samples with two initial levels of crystallinity, X_c = 1% and 11%, were prepared by cold crystallization at 80 ^°C. Whatever X_c and T_d, the total amount of the ordered phases (i.e. crystalline + mesophase) increased with draw strain, which could be ascribed to the formation of strain-induced mesophase at T_d = 60 or 70 ^°C but crystalline at 80 ^°C. Also, the molecular orientation of both the amorphous and ordered phases increased with draw strain. Whatever X_c, the orientation of the ordered phases was insensitive to T_d, whereas higher orientation in the amorphous phase was achieved at lower T_d, and the trend was more significant for X_c = 1% compared with 11%.     

Spectroscopic analysis of post drawing relaxation in poly(lactic acid) with oriented mesophase

Uniaxial deformation of amorphous poly(lactic acid) (PLA) film was performed at 60 °C (around the glass transition temperature). The deformed samples revealed a strain-induced mesophase, and its fraction and thermal stability increased with draw strain. Further annealing was performed in situ at constant length, at the drawing temperature for the films drawn to strains of 100% and 230%. Interestingly, the orientation of amorphous phase relaxed more rapidly for the 100% sample compared with the 230% one. This could be ascribed to the constraint effect of mesophase on the amorphous chains. In addition, the chains of mesophase relaxed slightly for the 100% sample while it retained high orientation for the 230% sample. Meanwhile, the mesophase fraction decreased, and the trend was more significant for the sample drawn to 100%. These effects can be ascribed to the melting of mesophase and the different thermal stabilities of the mesophases.     

High-velocity stretching of polyolefin tapes

Stretched polyolefin films and tapes are used in many packaging applications, such as BigBags. Stretching is elongation of polymer tapes in one direction, resulting in improved mechanical properties. Both, amorphous and crystalline polymers are in principle stretchable but linear, unbranched macromolecules are highly stretchable. Hence, the stretchability of e.g. branched low density polyethylene (PE-LD) is lower than of high-density polyethylene (PE-HD). Basic requirements for stretching of thermoplastics are known, but correlations between material parameters and stretching behaviour are scarce. Moreover, stretching of polymers is usually studied with tensile tests at stretching velocities much lower (1–500 mm/min) than in industrial processes (400–1000 mm/s), while results from high-velocity stretching tests or on production machines have not been published as of yet. We investigated high-velocity (800 mm/s) stretching of PE-LD, PE-HD and isotactic polypropylene films and tapes and which stretching parameters resulted in maximum mechanical properties. It was found that sample geometry, temperature, and the degree of stretching have a significant influence on the properties of stretched tapes, e.g. higher stretching temperature resulted in higher mechanical properties and orientation of crystallites. Furthermore, about 80% of the maximum stretching degree resulted in maximum mechanical properties.     

Transient shear flow behavior of concentrated long glass fiber suspensions in a sliding plate rheometer

In order to eventually predict the behavior of long fiber suspensions in complex flows commonly found in processing operations, it is necessary to understand their rheology and its connection to the evolution of fiber orientation and configuration in well defined flows. In this paper we report the transient behavior at the startup of shear flow of a polymer melt containing long glass fibers with a length (L) >1 mm, using a sliding plate rheometer (SPR). The operation of the SPR was confirmed by comparing the transient shear viscosity (η⁺) for a polymer melt and a melt containing short glass fibers (L < 1 mm) with measurements obtained from a cone-and-plate device, using a modified sample geometry that was designed to avoid wall effects. For the long fiber systems, measurements could only be obtained in the SPR because these systems would not stay within the gap of the rotational rheometer. Transient stress growth behavior of the long fiber systems was obtained as a function of shear rate and fiber concentration for samples prepared with three different initial orientations. Results showed that, unlike short fiber systems (with a random planar initial orientation) that usually exhibit a single overshoot peak followed by a steady state, η⁺ of the long fiber suspensions often passed through multiple transient regions, depending on the fiber concentration and applied shear rate. Additionally, η⁺ of the long fiber suspensions was found to be highly dependent on the initial orientation of the sheared samples. Finally, the initial and final fiber orientations of the long glass fiber samples were measured and used to initiate an explanation of the viscosity behavior. The results obtained in this research will be useful for future assessment of a quantitative correlation between transient rheology and the evolution of fiber orientation.     

Orientable edge colorings of graphs

An edge coloring of a graph is orientable if and only if it is possible to orient the edges of the graph so that the color of each edge is determined by the head of its corresponding oriented arc. The goals of this paper include finding a forbidden substructure characterization of orientable colorings and giving a linear time recognition algorithm for orientable colorings.An edge coloring is lexical if and only if it is possible to number the vertices of the graph so that the color of each edge is determined by its lower endpoint. Lexical colorings are, of course, the orientable colorings in which the underlying orientation is acyclic. Lexical colorings play an important role in Canonical Ramsey theory, and it is this standpoint that motivates the current study.     

“Structure and mechanical properties of blown films of ionomer-compatibilized LDPE nanocomposites”

Blown films based on low density polyethylene (LDPE) organoclay nanocomposites (NCs) were obtained by melt extrusion followed by film blowing, using a zinc ionomer of poly(ethylene-co-methacrylic acid) (Pema-Zn) as a compatibilizer. The parameters studied were the compatibilizer and the montmorillonite (MMT) contents that ranged from 0 to 20% and from 0 to 5%, respectively. The presence of clay hindered Pema-Zn crystallization indicating the existence of interaction between the Pema-Zn and the clay. Analysis of the nanostructure showed that the MMT was found inside microscopic domains of Pema-Zn distributed throughout the LDPE matrix. The addition of Pema-Zn improved the dispersion of the clay in LDPE films resulting in synergistic improvements in the mechanical properties. These improvements occur both in the machine and transverse directions. Thus, the presence of Pema-Zn is a determining factor in biaxiality and can clearly be attributed to the bidimensional laminar structure of clays such as MMT.     

高分子量级分含量对熔体挤出拉伸法制备聚丙烯微孔膜的影响

通过熔体挤出拉伸法以两种聚丙烯为原料制备微孔膜.通过考察原料分子量数据发现高分子量聚丙烯(PPH)在高分子量级分(重均分子量>106)含量上大于低分子量聚丙烯(F401).PPH的弛豫时间在相同条件下也远大于F401.红外二向光法结果表明,PPH在相同熔体牵伸比下片晶取向度较F401高.相同加工条件下PPH微孔膜片较F401成孔分布更均匀,孔径尺寸也更均匀.2种微孔膜孔隙率都随熔体牵伸比的增加而提高,微孔分布随着熔体牵伸比的提高和片晶取向度的增加而趋于均匀,孔尺寸也随之区域均匀.研究表明,聚合物树脂中高分子量级分含量是影响预制膜中片晶取向度、冷热拉伸成孔分布和尺寸均匀度的重要影响因素.     

Effect of Draw Ratio on the Morphologies and Properties of BPDA/PMDA/ODA Polyimide Fibers

3,3,4,4-Biphenyltetracarboxylic dianhydride/pyromellitic dianhydride/4,4-oxydianiline（BPDA/PMDA/ODA） polyimide copolymer fibers with different draw ratios were prepared from the imidization of polyacrylic acid（PAA） fibers via a dry-jet wet-spinning process.Their morphologies,microcrystal orientations,thermal stabilities,and mechanical properties were investigated via scanning electron microscopy（SEM）,wide angle X-ray diffraction（WAXD）,thermogravimetric analysis（TGA）,and tensile experiments.In order to acquire fibers with better mechanical performance,we aimed at obtaining the optimal draw ratio.Drawing during thermal imidization resulted in a decreased diameter of fiber from 25.8 μm to 16.9 μm corresponding to draw ratio from 1 to 3.5.WAXD results show that the degree of the orientation of the undrawn sample is 64.1％,whereas that of the drawn sample is up to 82％.The as-spun fiber and those with different draw ratios all exhibit high thermal stabilities,i.e.,the temperature at a mass loss of 5％ can reach as high as 570 ℃.The tensile strengths and tensile modulus of the fibers increase with the draw ratios,and the maximum tensile strength and modulus are 0.90 and 12.61 GPa,respectively.