Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Optical absorption of lithium metal vapor at high temperatures

Experimental results are reported for a unique spectroscopic device called the Plasma Spectroscopy Cell. Optical absorption of lithium metal vapor was observed at high density and temperature. Absorption spectra are analyzed using theoretical calculations of absorption cross sections for lithium-helium interactions, and singlet and triplet state transitions of diatomic lithium in the visible spectral range. This is believed to be the most complex example yet calculated in which absolute bound-bound, bound-free, free-bound, and free-free contributions for all possible optically allowed transitions are all included, in quite respectable agreement with experiment.     

肿瘤微波热疗的温度场预示及热损伤研究

本文将热损伤的产生和影响引入到肿瘤的微波热疗中。运用微波能量比吸收率SAR的分布分析了微波在组织中的传输和吸收过程,并对微波热疗过程中的温度场、热损伤分布以及血液灌注率的变化进行了数值模拟。     

Hawking Radiation of Dirac Particles in a Nonuniformly Rectilinearly Accelerating Black Hole

The Hawking radiation of Dirac particles on the event horizon of a nonuniformly rectilinearly accelerating black hole is studied in this paper. First, we construct the symmetrized null tetrad from which the spin coefficients and Dirac equation are derived. Next, by proposing generalized tortoise coordinate transformation, the decoupling problem of the Dirac equation with nonzero rest mass is solved. Finally, by analytic continuation, the Hawking thermal spectrum formula of Dirac particle for nonuniformly rectilinearly accelerating black hole is obtained.     

神光Ⅱ上柱形黑腔辐射驱动冲击波

利用神光Ⅱ的八路三倍频激光装置，驱动柱形黑腔产生的x 射线作辐射源驱动台阶铝样品产生冲击波，获得了清晰的冲击波图像，通过冲击波过台阶样 品的时间差获得冲击波速度和压力分别为31.2km/s和17.5×10⁵MPa.采用软x射线能谱 仪通过激光注入孔测量的辐射温度与采用冲击波法测量辐射温度的结果一致. 关键词： 冲击波 辐射驱动 辐射温度     

遥感器CCD驱动器热设计及其在摄像过程中的温度变化

CCD驱动器是航天成像遥感器摄像过程中的主要热源之一。防止CCD驱动器过热是保证其正常工作的重要方面。介绍了遥感器的工作模式和对CCD驱动器采取的热控制措施。通过热平衡试验,利用回归的方法,对CCD驱动器在摄像过程中的温度变化规律进行了分析,同时对热控制效果进行了评估。CCD驱动器工作时升温速率在0.85℃/min左右,整个摄像过程中最高温度约为26℃,所实施的热控制措施效果理想。     

Si微电阻桥温度分布与热传导特性的显微Raman光谱研究

采用显微Raman光谱方法对红外目标模拟器中重掺杂Si微电阻桥单元的热传导特性进行研究，根据Si桥的实际特性建立相应的Raman散射模型，通过测量Raman峰位的移动得到高功率激光辐照下测量点的温度.对Si桥桥面分别进行了沿某些特殊线段的逐点线扫描和覆盖全部桥面的面扫描，得到各点的温升及其分布.用基于有限元分析的软件结合Si桥结构参数对各测量点的温升进行了模拟计算，其结果在热导分布的基本趋势上与实验相一致.实验细致地揭示了热导分布的局域起伏，反映出实际器件的不均匀性，为改进器件设计、优化器件性能提供了实验依据. 关键词： Raman光谱 Si桥 温度分布 热导     

加热炉内板坯粘塑性下桡变形的研究

在加热妒内，由于高温及重力作用，板坯两端的悬臂将产生下桡变形。悬臂越长，下桡将越大，导致悬臂下桡部分与出口端墙相碰，影响出料而造成事故。本文对加热炉内板坯的下桡变形进行了分析计算。首先，建立了板坯的二维非稳态导热模型并用有限差分法计算了炉内板坯随时间的温度变化；然后建立了板坯悬臂粘塑性变形模型，用有限元法计算了高温条件下由重力引起的悬臂的下桡变形。由此理论模型计算出的板坯抽出温度与悬臂端下桡量与实测结果吻合良好，说明该理论模型及模型计算方法是正确的，可用于对装钢生产进行指导。     

Temperature‐modulated differential scanning calorimetry studies on the origin of double melting peaks in isothermally melt‐crystallized poly(L‐lactic acid)

In this work, the melting behaviors of nonisothermally and isothermally melt‐crystallized poly(L ‐lactic acid) (PLLA) from the melt were investigated with differential scanning calorimetry (DSC) and temperature‐modulated differential scanning calorimetry (TMDSC). The isothermal melt crystallizations of PLLA at a temperature in the range of 100–110 °C for 120 min or at 110 °C for a time in the range of 10–180 min appeared to exhibit double melting peaks in the DSC heating curves of 10 °C/min. TMDSC analysis revealed that the melting–recrystallization mechanism dominated the formation of the double melting peaks in PLLA samples following melt crystallizations at 110 °C for a shorter time (≤30 min) or at a lower temperature (100, 103, or 105 °C) for 120 min, whereas the double lamellar thickness model dominated the formation of the double melting peaks in those PLLA samples crystallized at a higher temperature (108 or 110 °C) for 120 min or at 110 °C for a longer time (≥45 min). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 466–474, 2007     

Lanthanum nitrate decomposition by both temperature programmed heating and citrate gel combustion

Thermal decomposition of lanthanum nitrate to lanthanum oxide was carried out by both temperature programmed heating (TPH) and citrate-gel combustion. The temperature programmed heating was carried out under flow of oxidizing (air), neutral (nitrogen) and reducing (25 vol.% hydrogen+argone mixture) gases, and the processes were controlled by simultaneous thermogravimetry and differential thermal analysis. It was shown that hydrogen atmosphere helps to reduce temperatures of all decomposition steps. The results of TPH were utilized to check the nature of residues in the products of lanthanum nitrate-to-oxide conversion performed via citrate-gel combustion technique.