Pressure effects on the phase transition of urea adducts withn-paraffins and polyethylene

The decomposition of urea adducts with hydrocarbons is treated as a first-order phase transition and the pressure dependence is studied up to 0.7 GPa for several kinds of adducts. The thermodynamic quantities at the decomposition of the adduct can be analysed as a sum of those quantities of the component materials. The transition from the orthorhombic to the hexagonal form of the adduct with polyethylene is also investigated by X-ray diffraction and the pressure dependence of the lattice parameters is measured for the adducts. The results are compared with the phase transition in the pure paraffin.     

光纤药物原位溶出度/释放度监测仪实时监测复方氯唑沙宗片体外溶出度

研制了光纤-光学传感-药物溶出监测仪并应用于复方氯唑沙宗片的实时-原位体外溶出度.分支光纤的一端与光源相接,另一端与检测器连接,其公共端部探头浸入于盛于溶出杯中的溶解液中.借联机的计算机进行数据记录及处理,对复方氯唑沙宗片的组分对乙酰氨基酚和氯唑沙宗的回收率在低、中、高三个浓度水平进行了试验,结果依次为98.3%,102.3%和103.1%及108.6%,98.7%和97.7%,其相应的RSD值为1.0%,1.4%和0.4%及1.7%,1.6%及1.3%.应用此监测仪对药片的溶出全过程进行了监控,并显示了药物的溶解曲线,相关的溶出参数可随时提取.试验证明,使用该仪器可获得药物溶出全过程的真实情况的信息.     

溅射参数对ZnO薄膜物性的影响

采用磁控溅射方法分别在ITO玻璃和硅片上成功制备了具有良好C轴取向的ZnO薄膜.并研究了溅射气压,基底温度,以及氧偏压对ZnO薄膜物性的影响,从而确定了制备ZnO薄膜的最佳溅射条件.     

低压离子色谱法测定土壤中速效钾

通常对土壤中速效钾的测定方法所用仪器昂贵。而低压离子色谱分析仪结构简单,操作简便,速度快,灵敏度高,价格低[1]。本文通过试验,确立了低压离子色谱法测定土壤速效钾的最佳条件,对实际样品的测定结果与推荐值呈显著相关性。1　实验部分土壤经风干、研磨,过100目土壤筛,测定其水份系数[2],贮存于密闭玻璃瓶内备用。准确称取2 0000g土样于50ml烧杯内,加20ml提取剂(0 05mol/LHCl+0 0125mol/LH2SO4),摇匀,25℃提取25分钟,离心分离。连接色谱仪、记录仪、蠕动泵(图1)。自制2J 3低压离子色谱仪,量程10×10μs,蠕动泵流速10刻度,记录仪量…     

Kinetics of the surface tension of micellar solutions: Comparison of different experimental techniques

The kinetics of the surface tension of micellar solutions of nonionic surfactant Triton X-100 is measured experimentally by means of three different techniques: oscillating jet, maximum bubble pressure and inclined plate. They allow to study the micellization kinetics at various time scales (from a few milliseconds to a few seconds) in fairly large concentration region up to 50 times CMC. The experimental data are satisfactorily explained by a theoretical model accounting for the kinetics of micellization, diffusion of surfactant species and expansion of the bubble interface. By this model are computed the characteristic times of diffusion and micellization, which are of comparable magnitude (about 5 to 200 ms), and the Gibbs' elasticity. The micellization time constant corresponds to the slow relaxation process known to coincide with the disintegration of micelles. Comparing our data with other data from literature one can conclude that more realistic information for the micellization kinetics is obtained by the maximum bubble pressure and the oscillating jet method. The inclined plate seems too slow to measure the relaxation processes in micellar solutions of this surfactant.     

Synthesis of Highly Porous Organic/Inorganic Hybrids by Ambient Pressure Sol-Gel Processing

This paper reports the synthesis of highly porous organic/inorganic hybrids by a two-step acid-base catalyzed sol-gel process and ambient pressure drying. In the method organic and inorganic precursors are copolymerized so as to incorporate organic ligands into the solid network. The two-step acid-base catalyzed process was used to prevent phase segregation during the hydrolysis and co-condensation of organic and inorganic precursors. The organic ligands incorporated into the solid gel network modify the surface chemistry. Thus, the wetting angle is significantly increased so that the collapse of the gel network is greatly reduced upon the removal of pore fluid during drying. Organic/inorganic hybrids with BET surface areas above 1250 m2/g, porosities above 75% and pore sizes of 8 nm have been synthesized.     

Tetraalkylammonium bromides in methanol: Small angle neutron scattering and vapor pressure measurements

Vapor pressure measurements and small angle scattering (SANS) experiments are reported and discussed for bispiperidinium (BP) bromide and n-tetrapentylammonium bromide solutions in methanol at 25°C. The BP⁺ ion which may be considered as a tetraalkylammonium (TAA) ion with pairwise connected alkyl chains, is used for the study of the effects due to flexible TAA alkyl chains. SANS intensities are calibrated with the help of the precise osmotic coefficients from the vapor pressure measurements.     

Thermally Induced Measurement Error by a Water-Cooled Enthalpy Probe

Errors in stagnation-pressure measurement, due to a large temperature gradient at the face of a water-cooled enthalpy probe, were experimentally measured and numerically simulated. Two probes were used to measure the stagnation-pressure in a dc plasma jet; a standard water-cooled enthalpy probe and an uncooled ceramic (Thoria) probe. There was a maximum difference of 10% between the two measurements, with the water-cooled probe measuring lower pressures. Numerical simulations of plasma flow around the probe showed that the magnitude of the error depends on the thickness of the thermal boundary layer. The measurement error causes a maximum of 3% error in velocity measurements, using the Bernoulli equation. This error is no worse than other measurement errors associated with water-cooled enthalpy probe meaurements.