HF激光脉冲与水柱表面相互作用产生电信号(英文)

研究了脉冲HF激光与水柱表面相互作用下电信号的产生过程。电信号显示了与激光能量线性相关的峰值间有时间间隔的两峰结构,且第二个尖峰在水柱底部的蒸汽腔塌缩后出现。实验还显示电信号的幅值和激光脉冲照射过程中是否存在膨胀和挤压的薄水层密切相关。如果在电池上边缘和石英平板(石英板紧邻电池,并与水柱上表面相接)之间存在一薄水层,电信号强度会增加10倍。     

Scheme for implementing quantum dense coding with W-class state in cavity QED

An experimentally feasible protocol for realizing dense coding by using a class of W-state in cavity quantum electrodynamics （QED） is proposed in this paper. The prominent advantage of our scheme is that the successful probability of the dense coding with a W-class state can reach 1. In addition, the scheme can be implemented by the present cavity QED techniques.     

Efficient scheme of quantum SWAP gate and multi-atom cluster state via cavity QED

In this paper, we propose a physical scheme to realize quantum SWAP gate by using a large-detuned single-mode cavity field and two identical Rydberg atoms. It is shown that the scheme can also be used to create multi-atom cluster state. During the interaction between atom and cavity, the cavity is only virtually excited and thus the scheme is insensitive to the cavity field states and cavity decay. With the help of our scheme it is very simple to prepare the N-atom cluster state with perfect fidelity and probability. The practical feasibility of this method is also discussed.     

Short Tm3+-doped fiber lasers with watt-level output near 2 μm

High-power operation of diode-pumped fiber lasers at wavelength near 2μm are demonstrated with short length of heavily Tm3 -doped silica glass fibers. With 7-cm long fiber, a laser at near 2 μm is obtained with the threshold of 135 mW, maximum output power of 1.09 W, and slope efficiency of 9.6% with respect to the launched power from a laser diode at 790 nm. The output stability of this fiber laser is within 5%.The dependence of the performance of fiber lasers on the operation temperature and cavity configuration parameters is also investigated.     

Study on hydrogen sulfide plasma passivation of 790-nm laser diode cavity surface

In order to improve the optical properties of the Ⅲ-Ⅴ laser diodes(LDs) by means of H2S plasma passivation technology,H2S plasma passivation treatment is performed on the GaAs(110) surface.The optimum passivation conditions obtained are 60-W radio frequency(RF)power and 20-min duration.So the laser cavity surfaces axe treated under the optimum passivation conditions.Consequently,compared with unpassivated lasers with only AR/HR-coatings,the catastrophic optical damage (COD) threshold value of the passivated lasers by H2S plasma treatment is increased by 33%,which is almost the same as that of (NH4)2Sx treatment.And the life-test experiment has demonstrated that this passivation method is more stable than(NH4)2Sx solution wet-passivated treatment.     

LOM and HOM damping study in a superconducting deflecting cavity for ALS at LBNL

Superconducting deflecting cavities can be used in synchrotron light source to generate subpicosecond X-ray pulses while the impedance of the lower order modes (LOM) and higher order modes (HOM) in the cavity should be kept below an accepted level to avoid beam instability. These modes can be damped by adding waveguide on beam pipe. Detailed simulation of Q in CST Microwave Studio is introduced and experiment results on an aluminum model cavity with damping waveguide are reported to make a comparison.     

Design of the low energy beam transport line for the China spallation neutron source

The design of the China Spallation Neutron Source (CSNS) low-energy beam transport (LEBT) line, which locates between the ion source and the radio-frequency quadrupole (RFQ), has been completed with the TRACE3D code. The design aims at perfect matching, primary chopping, a small emittance growth and sufficient space for beam diagnostics. The line consists of three solenoids, three vacuum chambers, two steering magnets and a pre-chopper. The total length of LEBT is about 1.74 m. This LEBT is designed to transfer 20 mA of H-pulsed beam from the ion source to the RFQ. An induction cavity is adopted as the pre-chopper.The electrostatic octupole steerer is discussed as a candidate. A four-quadrant aperture for beam scraping and beam position monitoring is designed.     

Novel Design of Laser with SBS Phase Conjugation Mirror

The beam quality of a single-rod Nd: YAG laser with wavelength of 1.06 m was improved almost up to the diffraction limit by using a phase-conjugating mirror (PCM) based on stimulated Brillouin scattering (SBS) with acetone as the SBS medium. The new start cavity, which is the concave-convex cavity operating near the limit of stability in the g diagram, and the phase conjugation cavity of the SBS oscillator were designed. The thermal lens of the material with focal lengths of less than 140 m at pump powers of 60 J was compensated by the PCM. The laser is Q-switched by the nonlinear reflectivity of the PCM and the system works with an average repetition rate of about 5 kHz and single Q-switch pulse showed a width of 10 ns. It is demonstrated that if the start cavity is fit for SBS and the SBS phase conjugation mirror can be optimized, the beam quality of solid laser can be surely enhanced because of this technology of nonlinear optics.