铁改性的Mo/ZSM-5催化剂上NO的选择性催化还原反应

采用浸渍法制备了Mo/ZSM-5, Fe/ZSM-5和不同Fe和Mo摩尔比的Fe-Mo/ZSM-5样品, 并以氨为还原剂对其NO选择性催化还原活性以及反应条件对催化性能的影响进行了研究. 结果表明, Fe-Mo/ZSM-5样品的NOx转化率明显比单独的Mo/ZSM-5和Fe/ZSM-5的高. 当n(Fe):n(Mo)为1.5时, Fe-Mo/ZSM-5样品具有最佳催化性能, 其NOx转化率在430 ℃时达到了96%, 并且能在高空速和不同O2气浓度的条件下保持高的催化活性. 同时采用XRD和XPS技术分别对催化剂的体相结构和表面性质进行了研究, 结果表明, 当n(Fe):n(Mo)=1.5时, Fe和Mo元素之间以及与载体HZSM-5之间存在较强的相互作用, 并且其表面的Mo3d的含量最高. 这可能与其高的催化活性有关. 另外还发现, 在反应过程中Fe-Mo/ZSM-5催化剂表面的氮氧物种主要是吸附态NO, 因此可以推测NO的催化还原反应机理是, 在催化剂表面上, 吸附态NO与吸附NH3物种直接反应生成氮气, 而非经过氧化为NO2的途径.     

Plasma Thermal Conversion of Methane to Acetylene

This paper describes a re-examination of a known process for the direct plasma thermal conversion of methane to acetylene. Conversion efficiencies (% methane converted) approached 100% and acetylene yields in the 90–95% range with 2–4% solid carbon production were demonstrated. Specificity for acetylene was higher than in prior work. Improvements in conversion efficiency, yield, and specificity were due primarily to improved injector design and reactant mixing, and minimization of temperature gradients and cold boundary layers. At the 60-kilowatt scale cooling by wall heat transfer appears to be sufficient to quench the product stream and prevent further reaction of acetylene resulting in the formation of heavier hydrocarbon products or solid carbon. Significantly increasing the quenching rate by aerodynamic expansion of the products through a converging–diverging nozzle led to a reduction in the yield of ethylene but had little effect on the yield of other hydrocarbon products. While greater product selectivity for acetylene has been demonstrated, the specific energy consumption per unit mass of acetylene produced was not improved upon. A kinetic model that includes the reaction mechanisms resulting in the formation of acetylene and heavier hydrocarbons, through benzene, is described.     

The hydroazocine route to highly functionalized pyrrolizidines

Studies of the preparation of 1,8-dihydroazocines and transannular cyclization of hydroazocines to produce functionalized pyrrolizidines are described. Results are presented which demonstrate that unsymmetrically substituted acetylenes bearing at least one electron withdrawing groups undergo efficient cycloaddition to 1 - β - styryl - 1,2 - dihydropyridine producing in a regio-selective fashion 3,4 - disubstituted - 1,8 - dihydroazocines. The dihydroazocines generated in this manner can be converted to 1 - formyl - Δ^4,5 - epoxyazocines which undergo interesting rearrangement reactions to form pyrrolizidines when subjected to methoxide deformylation followed by acid treatment. In addition, 1,6,7,8 - tetrahydroazocines can be converted to pyrrolizidines under bromination conditions. The intriguing chemical process which occur under the conditions outlined above are described.     

The pyrolysis of trimethylgermane and trimethylsilane

The number of products and the H₂/CH₄ ratio obtained from the flow pyrolyses of (CH₃)₃GeH and (CH₃)₃SiH were very different. The (CH₃)₃GeH decomposition is consistent with the following mechanism:

Full-size image

The pyrolysis of (CH₃)₃SiH was found to be much more complex, presumably due to the formation of silicon-carbon double bonded intermediates and the (CH₃)₂Si(H)CH₂ radical. We also present data which supports the presence of a H atom chain sequence during this pyrolysis.     

Stability of the FID sensitivity during an analysis in capillary GC

The sensitivity of an FID may change when the carrier gas flow rate changes during a chromatographic run. Sample parts which are eluted at reduced FID sensitivity produce a reduced peak area, hence are discriminated as compared to other components. Sensitivity changes were studied for hydrogen as carrier gas. For the detector tested, differences in the carrier gas flow rates of 1 ml/min shifted the FID sensitivity by 1 to 5% (depending on the fuel gas supply). Thus the stability of the sensitivity is no longer ensured as soon as the carrier gas flow rate is changed manually or by an automatic programmer during an analysis. Sensitivity drifts may also occur during temperature programmed runs with a pressure regulated carrier gas supply since the gas flow through the capillary drops with increasing temperature. Such shifts in the response became noticeable as soon as relatively high carrier gas flow rates combined with long range temperature programmes were used. The typical patterns of such discriminations are shown, closing with a discussion on the possibilities for minimizing such undesired effects.     

Synthesis of (+)-goniothalesdiol and (+)-7-epi-goniothalesdiol

A total synthesis of (+)-goniothalesdiol, a 3,4-dihydroxy-2,5-disubstituted tetrahydrofuran isolated from Goniothalamus borneensis (Annonaceae), and its 7-epimer is reported using oxycarbonylation methodology for construction of polyhydroxylated substituted heterocycles. Diastereoselectivity of addition of organometallic reagents to 2,3-O-isopropylidene-d-threose derivatives using theoretical calculations based on the semiempirical PM5 was studied.     

High temperature corrosion behaviour of M(Co,Ni)CrAIY-coatings on high temperature materials-microanalytical investigations

In our former investigations, the phenomenon high temperature corrosion (HTC) was described exemplarily on selected materialcoating combinations for blades of stationary gas turbines, mainly in the temperature region of up to 750° C. To answer the question, in which manner higher gas inlet and/or higher material surface temperature would influence the HTC behaviour, a special analytical technique—the integral layer profile analysis—was introduced to ameliorate concentration profile methods. By examining IN 738 LC specimens with CoCrAlY plasma spray coating, stressed by hot gas at 900° C, the limits of this system are shown by explaining the corrosion mechanism; the method is also used for other systems, e.g. U 520 with NiCrAlY coating at 750° C.     

Image analysis in the electron microscopy of cellulose protofibrils II. Digital correlation methods

Electron micrographs of parallel arrays of negatively stained ramie cellulose protofibrils were analyzed using the two-dimensional digital autocorrelation function (ACF). The method is based upon the statistical analysis of images in real space. The ACF shows strong parallel streaks of high correlation, and the lateral distance between adjacent streaks allows the mean interfibrillar distance to be estimated as 3.7 nm. The intensity profile along the streaks shows a weak modulation with peaks occurring at integral multiples of 3 or 6 nm. These results provide direct evidence that there is a regular axial texture in the protofibrils, and corroborate the conclusions previously drawn from optical diffraction analysis. Using the difference vectors found in the ACF it has been possible to reduce the picture noise level by linear integration, thereby obtaining an enhanced image. A preliminary result obtained in this way suggests that the projected protofibril morphology associated with the observed axial periodicity is a ribbon-like zigzag structure. Possible applications of the method for future work are discussed.     

Anodic hydroxylation of 1-carbomethoxy-1,2,3,4-tetrahydrocarbazoles

1-Carbomethoxy-1,2,3,4-tetrahydrocarbazole (1) and its 7-methoxy derivative (2) were oxidized at carbon felt anodes in acetonitrile containing 0.2 M LiClO₄ and 2-17 M water at potentials on the rising portion of the primary oxidation peak to yield products formed by formal substitution of the C-1 H atom with hydroxide. The resulting 1-hydroxy-l-carbomethoxy-1,2,3,4-tetrahydrocarbazole and its 7-methoxy derivative were isolated in 44 and 22% yields, respectively, when sodium bicarbonate was used to control acidity of the medium. Structures were elucidated by NMR, IR, elemental analysis, and mass spectrometry. Voltammetry at carbon-paste and glassy carbon electrodes showed that the oxidations proceed by an ECE or DISPI pathway. The rate-determining step is the reaction of water with a cation radical electrochemically generated from 1 or 2, involving either proton abstraction or nucleophilic addition.     

Thermodynamics of the conversion of aqueous glucose to fructose

The thermodynamics of the conversion of aqueous glucose to fructose has been investigated using both heat conduction microcalorimetry and high pressure liquid chromatography (HPLC). The reaction was carried out in both aqueous Tris/HCl buffer and in aqueous phosphate buffer in the pH range 7–8 using the enzyme glucose isomerase and the cofactors CoCl₂ and MgSO₄. The temperature range over which this reaction was investigated was 298.15–358.15 K. We have found that the enthalpy of reaction is independent of pH over the range investigated. A combined analysis of both the HPLC and microcalorimetric data leads to the following results at 298 15 K:ΔG° = 349 ± 53 J mol^-1, ΔH° = 2.78 ± 0.20 kJ mol^-1, and ΔC _p ^° = 76 ± 30 J mol^-1 K^-1. The stated uncertainties are based upon an analysis of both the random and systematic errors inherent in the measurements. Comparisons are made with literature data. The percent conversion of glucose to fructose has been calculated for the temperature range 300–373.15 K.