New perylene polyimides containing p‐n diblocks for sensitization in TiO2 solar cells

Three novel perylene polyimides (PPIs) containing p‐n diblock units were designed and synthesized for use in dye‐sensitized mesoporous TiO₂ solar cells. They all dissolve in m‐cresol and N‐methyl‐2‐pyrrolidone (NMP). Their visible light absorption, electrochemical and photoelectrochemical properties were systematically studied. The polyimides have band gap energies of 2.16, 2.19 and 2.25 eV deduced from ultraviolet–visible absorption spectra, and electron affinity (E_a) and ionization potential (IP) of ?3.93 and 6.10 eV for PPI1, ?3.94 and 6.13 eV for PPI2, ?3.93 and 6.59 eV for PPI3, respectively, deduced from cyclic voltammogram. Experimental data show that introduction of 4,4′‐bisaminetriphenylamine cannot only greatly enhance optic‐electro conversion efficiency, but also enhance the dissolubility which in favorable for making the devices. The relationship of structure and properties of PPI is discussed and the mechanism of photocurrent generation is explained. Copyright © 2004 John Wiley & Sons, Ltd.     

Characterization of non‐Cr‐based deoxidizers on Al alloy 7475‐T7651

The effects of three non‐chromate‐based deoxidizers, namely NaBrO₃/HNO₃, (NH₄)₄Ce(SO₄)₄/H₂SO₄ and Fe(III)/HF/HNO₃, on the Al alloy 7475‐T7651 were investigated. Several analytical methods were employed, including SEM, AES, transmission electron microscopy (TEM), electron energy‐loss spectroscopy (EELS) and glow discharge optical emission spectrometry (GDOES), to study the effects on the surface of this alloy after each treatment compared with the as‐received and alkaline‐cleaned alloy surfaces. The untreated alloy was found to have a thick oxide of 200–320 nm, consisting mainly of MgO. Alkaline cleaning results in an etching effect that thins the oxide and also deposits a thin silicate layer on the surface. In the case of the deoxidizers, there is significant removal of the native oxide of the alloy by the NaBrO₃/HNO₃ deoxidizer. There is also evidence of intermetallic attack on the alloy. The (NH₄)₄Ce(SO₄)₄/H₂SO₄ deoxidizer, which is a low‐etch‐rate deoxidizer, resulted in a slight thinning of the oxide. However, the effect was not significantly greater than with alkaline cleaning alone. The most effective deoxidizer in reducing the oxide thickness of the alloy is Fe(III)/HF/HNO₃, in which the etch rate was sufficiently high to remove completely the native oxide. In this case, equilibrium between oxide removal and the formation of new oxides on the alloy surface was achieved. Copyright © 2004 John Wiley & Sons, Ltd.     

非对称碰撞约束下形状记忆合金梁的随机响应与分岔

形状记忆合金(SMA)是二十一世纪具有形状记忆效应的新型智能材料.针对具有非对称约束的SMA梁,本文构造了碰撞振动系统.在无碰撞和有碰撞两种情况下,利用随机平均法给出了近似解析结果.数值模拟作为验证解析结果的工具.结果表明,系统能量的概率响应曲线具有非光滑特性.当约束位置发生变化时,系统会出现随机P分岔和D分岔.     

稀土元素在LD30铝合金真空钎焊中的作用

研究了添加La和Ce的Al-Si基钎料真空钎焊LD30铝合金接头的力学性能，微观组织形貌和EDS，并与未添加稀土元素的Al-Si基钎料真空钎焊接头进行对比。结果表明，添加稀土元素的LD30铝合金真空钎焊接头抗拉强度为288MPa，达母材抗拉强度的97．6％，明显高于未添加稀土的LD30合金真空钎焊接头。其机制在于La,Ce能够明显提高Al-Si基钎料与LD30铝合金的润湿性能，改善LD30铝合金真空钎焊接头焊缝及其基体中杂质元素的分布，促进钎料和母材中各元素的均匀扩散，从而提高真空钎焊接头的力学性能。     

The Glass Transition of Water and Aqueous Systems

After a brief introduction of the terms supercooling, amorphous solid state, glass transition and devitrification, the known ways of production of amorphous solid water are discussed. DSC experiments with quench cooled aqueous solutions show the phenomenon of glass transition and devitrification.This revised version was published online in November 2005 with corrections to the Cover Date.     

Al3Ti1B1RE细化剂对罐用铝材的细化效果及稀土的作用

采用XRD，OM，SEM，EDAX等探讨了一种新型Al3Ti1B1RE中间合金细化剂对罐用铝材的细化效果及RE的作用。结果表明，该细化剂对罐用铝材的细化效果优于进口和国产Al3Ti1B，且具有长效性，达6h后仍未见明显衰退，明显提高了该材料的强度和塑性；其细化效果及稳定性好的主要原因是：RE可降低铝液的表面能，增加铝液对细化核心(如TiAl3，TiB2)的润湿性，既充分发挥了异质形核作用，又防止了TiB2聚集沉淀倾向；RE也极易在结晶前沿富集造成成分过冷，阻碍了α-Al晶粒生长，并促进其在细化核心上形核；此外RE还兼有一定的净化、细化和变质作用，尤其是净化作用提高了该细化剂的冶金质量。     

锡铅银等低熔点合金中氧的测定方法研究

研究了锡铅银等低熔点合金中杂质氧的测定方法。针对这些金属高温下易挥发、分解的特点，选择适宜的加热温度，使用铜和石墨粉作为浴料，选择标准坩埚，以电流920A加热进行试验。对氧的质量分数为0.017%的试样，分析精密度为5.9%，加标回收率为91％－108％。     

钇对2618合金组织及性能的影响

采用X射线，光学显微镜及扫描电镜等手段研究了2618合金中的组织与相结构，并研究了元素钆在2618合金中的存在形式及其对合金力学性能的影响。结果表明，微量钆元素在铝合金中是以化合物形式存在的；钆对合金中的铸态组织及Al9FeNi仃形态没有影响。由于微量钆的加入，降低了铜与镁在2618合金中的固溶量，减少了时效析出相A2CuMg数量，从而降低2618合金的室温强度帮在250℃的高温瞬时强度；但由于微量钆减少了铜与镁在2618合金中的扩散速度，延缓了时效机的粗化，并由于第二相数量的增多，因此提高了2618合金在250℃经100h高温热暴露后的高温瞬时强度。     

石墨炉原子吸收法直接测定高温合金中硅

研究了混合基体改进剂，灰北、原子化温度以及共存元素的干扰，采用镧和钙作混合基体改进剂后，硅的灵敏度提高，抗干扰能力增强，可以用石墨炉原子吸收直接测定高温合多中硅。方法特征量为０．２ｎｇ，检出限为２．３μｇ／ｇ，对于含硅量为４００μｇ／ｇ左右的合金样品，相对标准偏差为５％左右，回收率在９０％－１１０％之间。     

高岭石无定形化的动力学研究

Amorphous kaolinite derivatives were prepared through mixing kaolinite with HCOOK and KOH solution. Ki-netics of kaolinite being turned into amorphous derivatvies was investigated by XRD. It showed that the transfor-mation included dynamic and diffuse controlling stages. And the active energy E₁=26.8kJ·mol^-1; E₂=12.2 kJ·mol^-1. TEM and SEM images showed that particle size of the amorphous derivatives was about 50nm. And the amorphous derivatives seemed like alumnsilicate gel， accompanied by some aggregates.