空间望远镜主镜的热光学特性分析

主镜是空间望远镜光学系统的重要组成元件,其热光学特性将为光学系统的热控设计提供依据。利用建立在集成分析基础上的热光学分析方法,分析了某空间望远镜主镜在三种不同的温度分布形式,即在径向温度、轴向温度、周向温度梯度的作用下对光学系统成像质量的影响,结合设计的要求,根据计算结果给出了许用温度梯度的范围。     

差分吸收光谱法测量大气污染的测量误差分析

差分吸收光谱技术被广泛地应用于测量大气中微量元素的浓度，尽管该技术利用最小二乘法来反演待测气体的浓度，能够得到很高的测量精度。但是，由于仪器本身的噪声以及测量波段其它气体的干扰等，使得仪器的测量有一定的误差，而且上述因素还决定着仪器的测量下限。对差分吸收光谱方法的测量误差以及引起误差的原因作了详细的分析。     

宽带膜厚实时监控过程中膜层折射率的确定方法

为了准确计算出镀膜过程中每层膜的折射率，介绍了实时监控过程中确定膜层折射率的2种方法：一种是由实测的透射比光谱直接反算出膜层的折射率；另一种是用最小二乘法的优化算法实时拟合折射率。试验结果表明：在线反算适合单点监控，所得折射率误差小于2%。然而在实际镀膜过程中,由于宽带内膜层参数误差较大,一般大于25%。为此，采用最小二乘法拟合，即在整个宽光谱范围内采集每个波长点的信息，所得结果误差很小，一般都在2％～5%之间,有时可达到10%,在很大程度上提高了实际镀膜时膜厚监控的精度。     

用γ计数率的变化定位核元件的技术研究

用标准放射源进行模拟核材料库房监控实验,当放射源被转移出系统的时候,在不同位置探测了γ计数率变化,根据γ计数率变化的距离平方反比规律实现了被转移的放射源的定位,并估算了该放射源的源强.     

关于合理确定集装箱码头装船顺序的算法

如何在给出箱区图和配载图的情况下,根据不同的装船方式,运用计算机程序确定合理的发箱和装箱顺序?本文主要依据实际数据,针对两种在码头实际装船作业中应用性较强的装船方式进行了研究,分别对其做了建立数学矩阵模型,制定合理算法,编写M ATLAB程序等工作,并论证了它们在实际操作中的可行性.本文的研究结果会在集装箱码头的实际装船作业中具有很强的应用性.     

电子束流品质对自由电子激光小信号增益影响的计算

对电子束有一定初始能量分散或角度分散时的自由电子激光小信号增益用较简便的方法进行了分析计算,并给出了一个渐近公式,结果与用计算机模拟解自由电子激光微分方程组得到的结果一致。     

双面加热环形通道内干涸点的确定

根据环形管通道内流体流动和换热的特点,以Kirillov和Smogalev提出的干涸点理论模型假设为基础,从最基本的质量守恒方程出发,并引入临界液膜厚度等相应的辅助模型,得到了双面加热环形通道内流动沸腾干涸点的理论模型。同时针对间隙为1.0mm和1.5mm的环形窄缝进行了低压低质量流速工况下干涸点的实验研究。比较发现理论模型预测值与实验结果基本相符。说明本文提出的理论模型适用于低压低流量条件下的窄环形通道。实验同时发现:环状流临界热流密度在系统压力为2.2MPa达到最大值,临界含汽量随质量流速的增大呈缓慢下降趋势。     

Mathematical Modeling, Control, Computer Simulation and Laboratory Experiments of a Spatial Servopneumatic Parallel Robot

In this paper, the special construction of a parallel robot, called spatial servopneumatic multi-axis test facility, will be discussed. The investigations include the following aspects: (i) the laboratory set-up of the robot, (ii) various results obtained in laboratory experiments, taking into account quite different control algorithms and command-input signals, (iii) a comparison of the laboratory experiments with the computer simulations of Part I of this paper, and ({vi}) a quality check of the results compared with the cost of the different controller realizations. The results of both the computer simulations and the laboratory experiments show: (i) The dynamic behavior of the parallel structure can be tremendously improved by using sophisticated nonlinear control algorithms. (ii) This improvement has to be paid by a drastically increased amount of work for deriving the model equations and control algorithms, and by augmented hardware cost of the sensing elements and controller electronics. (iii) Carefully developed model equations and identified model parameters provide theoretical models of the complex parallel structure that are very close to reality. This enables the design engineer to systematically investigate constructive alternatives of the design parameters, sensor and actuator concepts, and control strategies of the MAP prior to their hardware realization.This work has been supported by the German Science Foundation (DFG) under Contract No. Ha 1666/6-3.     

一种新型波长转换器的模块化设计

对一种新型结构全光波长转换器进行了高精度、高稳定度的模块化设计，并利用该模块实现对波长转换器参数的监控。结果表明这种新型模块对波长转换器的实现提供了可靠的保证，表现出较高的稳定度和实用性。     

Membrane introduction mass spectrometry

An overview of membrane introduction mass spectrometry (MIMS) is presented and comparisons are made with other direct sample introduction techniques. Special attention is given to the unique advantages and the limitations of newer variants on the MIMS technique, including affinity MIMS, reverse-phase and trap MIMS. The salient features of the interfaces used in MIMS are summarized and the various membrane materials commonly used are delineated. The applicability of MIMS is illustrated via discussion of

1. (i) bioreactor monitoring (represented by yeast fermentation),

2. (ii) environmental monitoring (illustrated by analysis of contaminated ground water samples) and

3. (iii) on-line chemical reaction monitoring (exemplified by the photolysis of aryl esters).

The applicability of MIMS to the analysis of environmental samples, including complex mixtures in water, air and soil, is noted.