一类复杂循环排队系统的计算机模拟及其在进程调度中的应用

讨论了顾客到达时间和服务时间与等待队列队长有关的排队系统模拟,顾客服务次数不止1次即出现循环的复杂排队系统,引入到达因子、服务台因子和循环因子,在串并联多服务台情形下建立了4类计算机模拟模型,给出该复杂循环排队系统在进程调度中的应用并进行了计算机模拟.     

基于MATLAB的异步电动机线性化控制系统的仿真

从异步电动机在同步旋转坐标系下的状态方程出发，在一定的条件下，对其系数矩阵简化．推出异步电动机的线性化控制模型．并基于该模型得出异步电动机的线性化控制系统．以给定电机为例，对该模型的有效性、响应用MATLAB进行仿真分析．验证的结果说明上述模型具有实用价值．     

二元液态金属Cu-Ni和Ag-Cu凝固过程的分子动力学模拟研究

用Quantum Sutton-Chen多体势对Ag6Cu4和CuNi液态金属凝固过程进行了分子动力学模拟研究.在冷却速率2×1012到2×1014K/s范围内,CuNi总是形成fcc晶体结构,而Ag6Cu4总是形成非晶态结构.考虑到CuNi及AgCu中原子半径之比分别为1.025和1.13,那么模拟结果证实了原子的尺寸差别是非晶态合金形成的一个主要影响因素.此外采用键对及原子多面体类型指数法对凝固过程中微观结构组态变化的分析,不但能说明二十面体结构在非晶态合金形成和稳定性中所起的关键作用,又有助于对液态金属的凝固过程、非晶态结构特征的深入理解.     

HLS直线加速器调制器系统设计与改造

介绍了合肥同步辐射光源速调管调制器改造项目.在新的设计中采用了开关型恒流PFN充电电源,计算了充电参数,建立了主放电回路的仿真模型,重点分析了电路中反向电压问题,依据仿真结果及分析设计了反向保护电路.给出了运行中的主要波形.最后介绍了新的调制器控制系统.     

机载海洋激光测深系统参量设计与最大探测深度能力分析

详细讨论了机载海洋激光测深系统最大测量深度与相关因子之间的关系，并利用最小可探测信噪比为判据，对机载海洋激光测深系统在白天和晚上工作进行了数值模拟，通过比较最大测量深度与激光脉冲峰值功率、接收视场角、接收口径和光谱接收带宽等关系，确定了系统的主要参量。以确定的参量建立的系统具有白天49m和晚上65m的最大测深能力，可完全满足在沿岸带以及岛礁的测量要求。     

Temperature-Dependent Dynamic Properties of LixMn2O4 in Monte Carlo Simulations

Monte Carlo (MC) simulations are used to simulate the voltage profile and the ionic conductivity s of Li ions in LixMn2O4 and its dependence on the lithium concentration x. The open circuit potential shows clearly the two plateaus in the charge/discharge curve, which agrees well with the experimental results. The two plateaus become more and more steep when the temperature is increased. The simulated ionic conductivity shows an M-shaped curve in the plot of ionic conductivity cr versus x when the simulation temperature is low. Interestingly,the minimum valley, which lies at the middle single-phase area near x=0.5, disappears gradually when the temperature increases to 453K.     

Recombination Efficiency in Double-Layer Organic Light-Emitting Devices

We analyse the influence of properties of organic/organic interface (OOI) on the characteristics of recombination efficiency of organic double-layer light-emitting diodes. Based on the disordered hopping theory model, spatial and energetic disorder of hopping states are also discussed for the case of space charge limited currents in hole transmitting layers but injection-limited currents in electron transporting layers. The results show that the recombination efficiency increases firstly and then decreases for different OOI parameters, and there is a maximum value changed with different spatial disorder parameters and energetic disorder scale. Different spatial disorder parameters make carrier mobilities change greatly, and the energetic disorder scale causes various localized state densities. Our calculated results are qualitatively in agreement with the experimental data.     

FAST ACCURATE PREDICTION OF BLANK SHAPE IN SHEET METAL FORMING

By using the Finite Element Inverse Approach based on the Hill quadratic anisotrop-ically yield criterion and the quadrilateral element, a fast analyzing software-FASTAMP for the sheet metal forming is developed. The blank shapes of three typical stampings are simulated and compared with numerical results given by the AUTOFORM software and experimental results, respectively. The comparison shows that the FASTAMP can predict blank shape and strain distribution of the stamping more precisely and quickly than those given by the traditional methods and the AUTOFORM.     

30J能量驱动类镍银X光激光的理论研究

 在1.2×10¹³W·cm^－2低功率密度下，对基频激光预主短脉冲驱动类镍银X光激光机理进行了数值模拟和理论分析。证实了在靶长23 mm范围内X光激光都能获得有效放大，取得了和实验相符合的结果。考虑了单柱面镜线聚焦沿靶长度方向功率密度的非均匀性对X光激光放大的影响，采用弯曲靶能有效克服折射以及单柱面镜线聚焦功率密度非均匀带来的不利影响。理论模拟给出的类镍银X光激光的出光下限泵浦功率密度也与实验符合得很好。理论模拟还表明，采用1%左右的预脉冲强度并对预主脉冲时间间隔进行优化，X光激光的输出能量和能量转换效率将获得大幅度提高。     

一种微型空调器的优化设计

介绍了一种微型空调器的研制背景及设计方案 ,采用仿真优化的设计手段对空调器的制冷、制热系统进行了优化设计 ,实践证明其设计是成功的。同时说明了该型空调器所具有的特点及应用场合