表面电沉积Ni—La2O3复合镀层的Fe26Cr1Mo不锈钢的氧化行为研究

Ｆｅ２６Ｃｒ１Ｍｏ不锈钢在９００℃氧化时，生成的氧化层在冷却过程中大量剥落，经表面共电沉积ＮｉＬａ２Ｏ３复合镀层后，抗热循环能力明显提高。     

Investigation of Glass-Like Sol-Gel Coatings for Corrosion Protection of Stainless Steel Against Liquid and Gaseous Attack

Glass-like sol-gel coatings have been investigated as corrosion protective coatings on stainless steel. Magnesium- and borosilicate coatings with thickness of about 100–700 nm and methyl-modified SiO2 coatings with a thickness of about 2 m were deposited on stainless steel plates by dip-coating. The coatings were densified between 400°C and 500°C in different atmospheres (N2, air) for 1 h. The corrosion protection against gaseous attack was investigated by accelerated corrosion tests, at 800°C in air for 1 h. A corrosion protection factor was calculated from the relation Fe/Fe2O3, determined by XRD on the surface of coated and uncoated samples. Methyl-modified SiO2 coatings showed a protection factor, which was 2 orders of magnitude higher than for the other coatings. Electrochemical investigations were performed on samples submerged in a NaCl solution for 200 h. The corrosion propagation, polarization resistance and impedance vector were measured. For accelerated corrosion tests, polarization intensity curves were determined for high potentials of up to 1 V. Again excellent results were obtained for the methyl-modified SiO2 coatings, which remained passive for 200 h. Results of the salt spray corrosion test, however, showed no corrosion protection by the sol-gel coatings. After 2000 h in the salt spray chamber the steel was corroded and the coatings peeled off. It is concluded that for the further development of these coatings an improved interfacial passivation will be required.     

柱前衍生-高效液相色谱法测定钢及合金中钨和钼

以tiron作为柱前衍生试剂,用含3mmol·L-1pH 3.8的HOAc-NaOAc,40mmol·L-1TBA-Br和2mmol·L-1tiron的甲醇-水溶液(53+47)作流动相,在C18柱上,于15min内实现了WO42-、MoO42-的分离测定。钨和钼的检出限分别为5.98和3.20ng·ml-1。方法快速,选择性好,用于钢及合金中高含量钨和钼的测定,结果与标准值相符。     

恒电量瞬态扰动测量Tafel斜率及数据积分处理

提出了一个三参数积分法拟合恒电量强极化数据以测定Tafel斜率的新方法.实验证明,恒电量瞬态扰动测量碳钢在酸溶液中的腐蚀,获得的Tafel斜率与消除了溶液电阻影响的Tafel外推结果有很好的一致性,说明恒电量法有效地消除了溶液电阻对该体系测量结果的影响,并且通过电化学和失重实验验证表明,这种快速测量可以获得准确的腐蚀速率.这种新的恒电量强极化积分算法相对微分法的优势体现在算法简捷和用于数值计算的数据具有较高的信噪比,因此能够提高测量精度.     

Use of kinetic plots for relative assessment of reactor throughput and energy consumption

The progress of high temperature processes is generally described in terms of variation of the degree of conversion () with time (t). The present paper outlines a procedure for making use of-t plots for comparative assessment of productivity and energy requirements for a test system with respect to a reference, on the basis of some simplifying assumptions. It is assumed that the throughput is inversely proportional to reaction time as in the case of batch reactors and plug flow reactors. It is also assumed that the energy requirement is a simple function of process temperature. The principles outlined is illustrated with reference to some laboratory data for reduction of iron oxide by coal.The authors wish to thank Prof. P. R. Rao, Director National Metallurgical Laboratory, Jamshedpur, India, for providing facilities for experimental work and for according permission to publish this work.     

Uranium association with corroding carbon steel surfaces

We investigated the association of uranium with clean and corroded surfaces of 1010 carbon steel. Studying steel contaminated by uranium species will have an important effect on the development of methods used to clean radioactively contaminated metal waste. X‐ray photoelectron spectroscopy, synchrotron infrared microspectroscopy and laboratory‐based Fourier transform infrared analysis of steel surfaces exposed to uranyl nitrate showed the presence of crystallized hydrated uranyl oxides, uranyl hydroxides, iron oxyhydroxides and iron oxides. In general, heavily corroded areas physically shield the uranium species, which tended to associate spatially with hydroxyl groups and lepidocrocite. Lightly corroded areas contained uranium species with stronger axial U–O bonding. Infrared spectroscopy, Rutherford backscattering spectroscopy and energy‐dispersive spectroscopy mapping analysis revealed that the uranium species are well distributed within the upper micron of the thick corrosion layer and associated more with areas of high hydroxide content. Parameters such as the concentration of uranyl nitrate solution used to expose the carbon steel coupons, the method of contamination (dipped or sprayed with dilute uranyl nitrate solution) and the degree of corrosion (accelerated corrosion before and/or after contamination) played significant roles in the distribution and nature of the uranyl hydroxide/iron oxyhydroxide corrosion products found on the surface of all coupons. These factors must be considered in the development and optimization of decontamination processes for metal waste. Copyright © 2003 John Wiley & Sons, Ltd.     

Anodic behavior of nickel-based alloys in the electrolytic production of NF3

The Ni-based alloys, such as Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si, prepared by hot isostatic pressing (HIP) at 1000 °C under 2 × 10⁸ Pa for 2 h were employed as the anodes for electrolytic production of NF₃. The current efficiencies for NF₃ formation were 42-38, 52-40, 52-47, 63-62, 50 and 41% for Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloys, respectively. The current efficiencies only on Ni-Cu alloys with Cu concentrations lower than 10 mol% were almost the same as those on Ni sheet and HIPed Ni anodes, whereas those on the other alloys used in this study were smaller compared with those on both Ni anodes. On the other hand, the current losses caused by anodic dissolution of Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloy electrodes were 7.95-4.42, 6.40-7.02, 5.60-6.30, 3.34-6.33, 5.10 and 0.18%, respectively. The anode consumptions of Ni-5 mol% Cu and Ni-5 mol% Si alloys were almost the same or smaller compared with those of Ni sheet and HIPed Ni electrodes, though those of other alloys used were large compared with those of both Ni anodes. Consequently, addition of Cu to the nickel matrix is available for a cheaper cost of anode with keeping a same current efficiency as that on the Ni anode and addition of Si to the nickel matrix is effective for decreasing anode consumption largely. A Ni sheet electrode containing a trace of impurities, such as Co, Mn, Ag and Al, is also favorable as the anode for electrolytic production of NF₃.     

RP-HPLC study of redox equilibria in vanadium-PAR binary and ternary systems: Direct determination of vanadium in steel

The reversed-phase high-performance liquid Chromatographic (RP-HPLC) behaviour of the binary chelates of V(V) and V(IV) with 4-(2-pyridylazo) resorcinol (PAR) and ternary chelates of vanadium with PAR and auxiliary ligands: hydrogen peroxide, hydroxylamine, tartrate and citrate were studied using a C₁₈ column. The complex double-peak chromatograms of V(IV)/V(V)-PAR systems were studied and the origin of each peak was proved. Vanadium in ternary systems with PAR and hydrogen peroxide was found exclusively in V(V)-H₂O₂-PAR complex (single peak on the chromatogram) despite its initial oxidation state. The double role of hydroxylamine (complex agent and reductor) in vanadium systems with PAR was confirmed: in the V(V) system three species were identified (V(V)-PAR, V(V)-NH₂OH-PAR and V(IV)-PAR), but in the V(IV) system only two: V(IV)-PAR and V(V)-NH₂OH-PAR. Citrate and tartrate giving single peak were found as auxiliary ligands in ternary V(V) systems of analytical importance. Due to its masking potential towards iron (III) ions, citrate was chosen as the most suitable third component of a ternary vanadium system with PAR, to form the basis of an RP-HPLC method for direct determination of V in steel.     

混合控制下腐蚀过程的电化学动力学参数测定

通过恒电量脉冲技术测定Q235碳钢在天然海水中腐蚀过程的电化学动力学参数. 分别利用不同极化幅度的恒电量瞬态响应分析获得极化电阻和Tafel斜率, 进而计算腐蚀电流icorr. 并对比了恒电量方法和考虑扩散影响的稳态极化曲线方法的测量结果. 结果表明, 采用恒电量强极化积分算法(CPSI)获得的Tafel斜率与极化曲线方法有很好的相关性. 同时, CPSI测定的阴极Tafel斜率符合氧还原反应的理论Tafel斜率值. 因此, 采用恒电量瞬态响应测量大大减小了浓差极化的影响, 有利于快速测定电荷传递和扩散传质混合控制下腐蚀过程的电化学动力学参数.     

Loss of stability by migration and chemical reaction of Santonox R in branched polyethylene under anaerobic and aerobic conditions

Plaques of branched polyethylene stabilized with 0.1 wt.% 4,4′-thiobis(6-tert-butyl-3-methylphenol) [Santonox^® R] were aged at different temperatures between 75 and 95 °C in anaerobic (nitrogen or water) and aerobic (air or water saturated with air) media. Antioxidant concentration profiles were obtained by oxidation induction time (OIT) measurements using differential scanning calorimetry. Results obtained by high performance liquid chromatography of extracts confirmed that the gradual decrease in OIT with increasing ageing time was due to migration of antioxidant to the surrounding medium. The antioxidant concentration profiles along the plaque thickness direction were flat in the plaques aged in the non-aqueous media indicating that the migration of antioxidant to the surrounding medium was controlled by the low evaporation rate at the material boundary. Crystals of antioxidant were detected by optical microscopy on the samples exposed to nitrogen. The similarity of the antioxidant concentration profiles obtained after ageing in nitrogen and in air suggested that the fraction of the antioxidant oxidized is negligible in comparison with the loss of antioxidant by migration to the surrounding media. The antioxidant concentration profiles along the plaque thickness direction obtained after ageing in water were less flat, suggesting faster dissolution in the water phase than evaporation in the case of non-aqueous ageing. The antioxidant diffusivity could be determined from the aqueous experiments and was in reasonable agreement with data reported by Moisan. For the samples exposed to water, the loss of antioxidant was faster from the samples exposed to water saturated with air. This difference is attributed to a faster degradation of the antioxidant in the oxygen-containing water phase increasing the mass transport from the polymer phase boundary to the water phase.