采用热处理方法提高MEH-PPV单层聚合物有机发光二极管发光性能的研究

对以MEH－PPV为发光层的单层聚合物有机发光二极管（OLED）器件在最佳条件下进行真空热处理，并用金相显微镜观察施加电压后器件的阴极表面形貌。发现处理后的器件阴极表面的气泡及黑斑明显减少。器件的发光性能显著提高。与未经处理的器件相比，最大相对发光强度提高了一个数量级、启亮电压降低了2．0V，半寿命提高了12．7倍。初步分析表明热处理方法提高器件发光性能的主要原因在于有效地减少了器件在工作过程中由于焦耳热产生的某些气体，从而减少阴极表面气泡及黑斑的出现，另一方面，热处理方法也增强了有机发光层与阴极接触界面的结合力，提高电子注入水平。     

一项从CAA到CAD的工作 ～正交优化法与SPICE相结合

电子电路的计算机辅助设计方法是促进电子技术发展的一种有效工具。本文介绍如何将行之有效的正交优化法与国际盛行的模拟电子电路的分析程序ＳＰＩＣＥ相结合，形成了ＡＣＯＤ软件，将ＣＡＡ扩展为ＣＡＤ。     

示差半微分循环伏安法研究琥珀酰胆碱在水/硝基苯界面的传递行为

研究了油/水界面电解的示差半微分循环伏安行为。在0.01mol/L LiCl(w)-0.01mol/L TBATCIPB(nb)体系“电位窗”比TBATPB(nb)向正方向扩展约50mV,残余电流基本消除,使“电位窗”内的平台向左右拓宽约50mV。算得界面电容约为16μF/cm~2。考察了琥珀酰胆碱离子在w/nb界面的传递伏安特性,结果与一般半微分循环伏安法相似。但峰形改善,检测限降低一个数量级(1×10~(-6)mol/L),相对标准偏差在5％以内,可用于定量测定琥珀酰胆碱。     

Analysis of Experiments on Determining the Turbulent Mixing Constant on the Basis of Two-Dimensional Calculations

Based on numerical calculations, the experiments on mixing at the interface of gases are analyzed. Single-mode and random disturbances of the interface and superposition of random disturbances onto long-wave perturbations are considered. Possible reasons for the higher value of the mixing constant obtained in the experiments are discussed.     

Molecular weight dependence of diblock copolymer segregation at a polymer/polymer interface

Utilizing forward recoil spectrometry (FRES), we have determined the segregation isotherm which describes the interfacial excess z_i^* of diblock copolymers of poly (d₈-styrene-b-2-vinylpyridine) (dPS-PVP) at the interface between the homopolymers PS and PVP as a function of ?_∞, the volume fraction of diblock copolymer remaining in the host homopolymer. All the samples were analyzed after annealing at temperatures and times sufficient to achieve equilibrium segregation. The effect of the degree of polymerization of both the diblock copolymers and the host homopolymers on the segregation isotherm is investigated. When the degree of polymerization of the homopolymer is much larger than that of the diblock copolymer, the normalized interfacial excess (z_i^*/R_g), where R_g is the radius of gyration of an isolated block copolymer chain, is a universal function of that portion of the block copolymer chemical potential due to chain stretching. The existence of such a universal function is predicted by theory and its form is in good agreement with self-consistent mean field calculations. Using these results, one can predict important aspects of the block copolymer segregation (e.g., the saturation interfacial excess) without recourse to the time-consuming numerical calculations. © 1994 John Wiley & Sons, Inc.     

等厚双层涂层材料受集中力作用的平面问题理论解

界面应力的正确评价是分析薄膜涂层材料力学特性的难题之一。利用镜像点法和Dirichlet等值性原理，本文推导了等厚双层薄膜涂层材料受表面集中力作用的平面问题理论解。该显式理论解是以固定在各镜像点上的局部坐标系下的Goursat应力函数的形式给出的。对应于高阶镜像点的应力函数，可通过递推的方法，从对应于低阶镜像点的应力函数求得，而且也易于计算机编程。随着镜像点阶数的增大，它与界面的距离也越来越大，因而相对应的应力函数对界面应力的影响越来越小。最后的算例表明，只需考虑前面有限个镜像点，便可获得足够精度的解。该理论解可作为格林函数，以求解复杂问题的理论解，也可用作边界元法的基本解，提高数值计算的精度和效率。     

开关型霍尔传感器的原理与工程实现

介绍了开关型霍尔传感器的工作原理，设计了适用于工程测量的具体线路，并分析了该线路的特点。     

The interlace polynomial of a graph

Motivated by circle graphs, and the enumeration of Euler circuits, we define a one-variable “interlace polynomial” for any graph. The polynomial satisfies a beautiful and unexpected reduction relation, quite different from the cut and fuse reduction characterizing the Tutte polynomial.It emerges that the interlace graph polynomial may be viewed as a special case of the Martin polynomial of an isotropic system, which underlies its connections with the circuit partition polynomial and the Kauffman brackets of a link diagram. The graph polynomial, in addition to being perhaps more broadly accessible than the Martin polynomial for isotropic systems, also has a two-variable generalization that is unknown for the Martin polynomial. We consider extremal properties of the interlace polynomial, its values for various special graphs, and evaluations which relate to basic graph properties such as the component and independence numbers.     

基于FPGA的42英寸全色PDP存贮控制电路的实现

从等离子体平板显示器(PDP)的发光原理出发，分析和研究了存贮控制电路的工作原理，提出基于FPGA的电路设计方案，并给出数据整理电路和驱动信号产生电路的具体电路框图，最后给出部分仿真波形．